CD00065252 RS-232 - Datasheet Archive

 

Softec's Complete Motor Control Starter Kit for ST7MC DATA BRIEF The Softec Motor Control Starter Kit for ST7MC (ST ordering

 

ST7MC-KIT/BLDC Softec's Complete Motor Control Starter Kit for ST7MC DATA BRIEF The Softec Motor Control Starter Kit for ST7MC (ST ordering code: ST7MC-KIT/BLDC) is an integrated system designed to provide you with a complete, ready-to-use motor control application for the ST7MC family of microcontrollers. It allows real-time control of Three-Phase Brushless DC and AC Motors in all control topologies from a PC-based GUI, or in standalone operation. Figure 1. Motor Control Starter Kit for ST7 The Control Panel software provides an easy-touse interface to configure, start and run the motor, modify parameters and evaluate ST7FMC motor control features, then generate header files for your own motor control application. The kit also comes with the STXF-INDART/USB in-circuit debugger/programmer and STVD7 integrated development environment that allow you to take advantage of the ST7FMC's on-chip resources for in-circuit programming and in-circuit debugging. Starter Kit Architecture Motor Control evaluation board ­ application board with ST7FMC, built-in power stage and optoisolation board, is designed to directly drive AC and DC motors. It also includes USART/LIN, EEPROM, potentiometers, sensor inputs for your application. Brushless DC motor ­ the included 24V DC motor is ready for direct connection to the Motor Control evaluation board. Control Panel ­ graphical user interface on your host PC that allows you start up and run the motor in just minutes, then fine tune parameters and output header files for your own application. STXF-INDART/USB ­ in-circuit debugging and incircuit programming tool that provides the hardware interface with the host PC via USB and with your ST7FMC via 10-pin in-circuit communication (ICC) connection. August 2005 STVD7 for inDART ­ Integrated development environment for writing, building and debugging your application. Optoisolation board ­ board with two 10-pin ICC connectors (In/Out) provides galvanic isolation between the in-circuit debugging/programming tool and any target board supplied by high voltage. It is included with the Motor Control Starter Kit, or can be ordered separately (ST ordering code: ST7-ICC/OPTOISOL). Induction motor ­ 240V/800W Selni three-phase induction motor for use with the Motor Control Starter Kit using induction motor default values (for evaluation purposes). It is not included with the kit, but can be ordered separately (ST ordering code: ST7MC-MOT/IND). CD00065252 CD00065252 For further information contact your local STMicroelectronics sales office. Rev 1 1/3 www.st.com 3 ST7MC-KIT/BLDC Key Features Motor Control board: Motor and board input power stage Auxiliary power supply and voltage rectification Push buttons, trimmers for standalone operation Hall sensor input 10-pin ICC connector for in-circuit programming and in-circuit debugging Prototyping area RS-232 RS-232 connector Optoisolation board Tachometer input for closed-loop controlled AC motors Three-phase outputs to motor Figure 2. Control panel settings interface Control Panel software: Parameter configuration for BLDC and 3-Phase Induction Motors Basic settings interface for configuring motor, start-up and real time parameters Advanced settings interface for configuring frequency, speed range, stop conditions, etc. Outputs header files for your application taking into account modifications to the configuration STXF-INDART/USB: 10-pin ICC connection USB connection to host PC Two breakpoints Advanced breakpoints on data, access type, access range, stack. For more information about inDART in-circuit debuggers/programmers, please refer to the ST7xxxxINDART Data Brief. For further information about the Motor Control Starter Kit, please refer to www.st.com/mcu, or the Softec internet site www.softecmicro.com. Revision history Date 30-Aug-2005 2/3 Revision 1 Changes Initial release. CD00065252 CD00065252 ST7MC-KIT/BLDC Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners © 2005 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com CD00065252 CD00065252 3/3