SPS-93120MG SPS-93120BMG OC-48 STM-16 1000BASE-ZX IEC-60825 1000BASE-LX OC-12

SPS-93120MG 1

Optoway SPS-93120MG SPS-93120MG 1 * SPS-93120MG SPS-93120MG / SPS-93120BMG SPS-93120BMG (RoHS Compliant) 3.3V / 1550 nm / Multirate SFP LC SINGLE-MODE TRANSCEIVER * FEATURES DESCRIPTION l Hot-Pluggable SFP Footprint LC Optical Transceiver l Small Form-Factor Pluggable (SFP) MSA compatible l Compliant with SONET OC-48 OC-48 (LR-2) / SDH STM-16 STM-16 (L-16.2) l Compliant with Fibre Channel 1x/2x SM-LC-L FC-PI l Compliant with IEEE 802.3z 1000BASE-ZX 1000BASE-ZX l 1550 nm DFB LD Transmitter l APD High Sensitivity Receiver l 31 dB Power Budget at Least l Distance up to 120 km l AC/AC Coupling according to MSA l Single +3.3 V Power Supply l RoHS Compliant l 0 to 70oC Operation: SPS-93120MG SPS-93120MG l -10 to 85oC Operation: SPS-93120BMG SPS-93120BMG l Class 1 Laser International Safety Standard IEC-60825 IEC-60825 Compliant The SPS-93120MG SPS-93120MG series single mode transceivers is small form factor pluggable module for bi-directional serial optical data communications such as SONET OC-48 OC-48 / SDH STM-16 STM-16, Gigabit Ethernet 1000BASE-LX 1000BASE-LX and Fibre Channel 1x/2x SM-LC-L FC-PI. It is with the SFP 20-pin connector to allow hot plug capability. This module is designed for single mode fiber and operates at a nominal wavelength of 1550 nm. A guaranteed minimum optical link budget of 31 dB is offered which can correspond to a link distance of over 120 km (assuming worst case fiber loss of 0.22 dB/km). The transmitter section uses a multiple quantum well 1550 nm DFB laser and is a class 1 laser compliant according to International Safety Standard IEC-60825 IEC-60825. The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. APPLICATIONS This single mode transceiver is a Class 1 laser product. It complies with IEC-60825 IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug. l l l l SONET OC-48 OC-48 / SDH STM-16 STM-16 SONET OC-12 OC-12 / SDH STM-4 SONET OC-3 / SDH STM-1 Gigabit Ethernet / 1X/2X Fibre Channel LASER SAFETY ORDER INFORMATION P/No. SPS-93120MG SPS-93120MG SPS-93120BMG SPS-93120BMG Bit Rate (Mb/s) Multirate* Multirate* SONET /SDH Distance (km) 120 120 Wavelength Package (nm) 1550 DFB LC SFP 1550 DFB LC SFP Temp. TX Power RX Sens. RoHS (oC) (dBm) (dBm) Compliant 0 to 70 5 to 1 -30 Yes -10 to 85 5 to 1 -30 Yes Multirate*: 2.67 Gb/s / OC-48 OC-48 / 2X FC / GbE / 1X FC / OC-12 OC-12 / OC-3 Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature Power Supply Voltage Symbol Tstg Topr Vcc Min -40 0 -10 -0.5 Max 85 70 85 3.6 Units o C o C Min 3.13 0 -10 Typ 3.3 Max 3.47 70 85 300 2670 Notes SPS-93120MG SPS-93120MG SPS-93120BMG SPS-93120BMG V Recommended Operating Conditions Parameter Power Supply Voltage Operating Case Temperature Power Supply Current Data Rate Symbol Vcc Topr ICC (TX+RX) 125 230 2488 Units / Notes V o C / SPS-93120MG SPS-93120MG o C / SPS-93120BMG SPS-93120BMG mA Mb/s * OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 1/1/2008 V2.0 Optoway SPS-93120MG SPS-93120MG 2 * Transmitter Specifications (0 oC < Topr < 70 oC, 3.13V < Vcc < 3.47V) Parameter Symbol Min Typ Max Units Notes Optical Optical Transmit Power Po 1 -5 dBm 1 Output Center Wavelength 1500 1570 nm Output Spectrum Width -1 nm -20 dB Width Side Mode Suppression Ratio SMSR 30 dB Extinction Ratio ER 8.2 -dB Output Eye Compliant with Telecordia GR-253-GORE GR-253-GORE and ITU-T Recommendation G.957 Optical Rise Time tr 150 ps 20 % to 80% Values Optical Fall Time tf 150 ps 20 % to 80% Values Relative Intensity Noise RIN -120 dB/Hz Dispersion Penalty 2.5 dB 2 Electrical Data Input Current Low IIL -350 µA Data Input Current High IIH 350 µA Differential Input Voltage VIH - V IL 0.5 2.4 V Peak-to-Peak TX Disable Input Voltage Low TDIS, L 0 0.5 V 3 TX Disable Input Voltage High TDIS, H 2.0 Vcc V 2 TX Disable Assert Time T ASSERT 10 µs TX Disable Deassert Time TDEASSERT 1 ms TX Fault Output Voltage - Low TFaultL 0 0.5 V 4 TX Fault Output Voltage - High TFaultH 2.0 Vcc+0.3 V 4 1. Output power is power coupled into a 9/125 µm single mode fiber. 2. Specified at 2400 ps/nm dispersion over G.652/G 652/G.654 fiber with center wavelength range of 1500 to 1580 nm. 3. There is an internal 4.7K to 10K ohm pull-up resistor to VccTX. 4. Open collector compatible, 4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage). Receiver Specifications (0oC < Topr < 70oC, 3.13V < Vcc < 3.47V) Parameter Symbol Min Typ Max Optical Sensitivity @ OC-48 OC-48 Sens1 -9 -30 Sensitivity @2X Fibre Channal Sens2 -9 -30 Sensitivity @Gigabit Ethernet Sens3 -9 -30 Sensitivity @OC-12 OC-12 Sens4 -9 -30 Sensitivity @OC-3 Sens5 -18 -30 Signal Detect - Asserted Pa -28 Signal Detect - Deasserted Pd -40 -Signal detect - Hysteresis 1.0 -Wavelength of Operation 1100 -1600 Electrical Differential Output Voltage VOH VOL 0.6 2.0 Output LOS Voltage - Low VOL 0 0.5 Output LOS Voltage - High VOH 2.0 Vcc+0.3 5. Measured at 2 23-1 PRBS at BER 1E-10 1E-10. 6. Measured at 2 7-1 PRBS at BER 1E-12 1E-12 . 7. Open collector compatible, 4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage). Units dBm dBm dBm dBm dBm dBm dBm dB nm V V V Notes 5 6 6 5 5 Transition: low to high Transition: high to low 7 7 * OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 1/1/2008 V2.0 Optoway SPS-93120MG SPS-93120MG 3 * CONNECTION DIAGRAM PIN Signal Name 1 2 3 TX GND TX Fault TX Disable 4 MOD-DFE2 5 MOD-DEF1 6 MOD-DEF0 7 8 9 10 N/C LOS RX GND RX GND Description PIN Transmitter Ground Transmitter Fault Indication Transmitter Disable (Module disables on high or open) Modulation Definition 2 Two wires serial ID Interface Modulation Definition 1 Two wires serial ID Interface Modulation Definition 0 Ground in Module Not Connected Loss of Signal Receiver Ground Receiver Ground 11 12 13 RX GND Receiver Ground RX DATA OUT- Inverse Receiver Data Out RX DATA OUT+ Receiver Data Out Signal Name Description 14 RX GND Receiver Ground 15 Vcc RX Receiver Power 3.3V±5% 16 Vcc TX Transmitter Power 3.3V±5% 17 18 19 20 TX GND TX DATA IN+ TX DATA INTX GND Transmitter Ground Transmitter Data In Inverse Transmitter Data In Transmitter Ground Module Definition Module Definition MOD-DEF2 PIN 4 MOD-DEF1 PIN 5 MOD-DEF0 PIN 6 Interpretation by Host 4 SDA SCL LV-TTL Low Serial module definition protocol Module Definition 4 specifies a serial definition protocol. For this definition, upon power up, MOD-DEF(1:2) appear as no connector (NC) and MOD-DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the 2-wire serial CMOS E 2PROM protocol of the ATMEL AT24C01A/02/04 AT24C01A/02/04 family of components. * OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 1/1/2008 V2.0 Optoway SPS-93120MG SPS-93120MG 4 * RECOMMENDED CIRCUIT SCHEMATIC VeeT Tx_DISABLE Tx_FAULT (1,17,20) 3 Tx_DISABLE 2 Tx_FAULT 4.7K to 10K TD + LD Driver 18 TD + Z=50 100 TD - 19 TD Z=50 VccT 1H 16 Vcc 3.3V 10F 10nF 10F 10nF SerDes IC 1H VccR 15 10F 10nF RD - 12 Protocol IC RD Z=50 100 POST Amp RD + 13 RD + Z=50 4.7K to 10K LOS VeeR MOD_DEF(0) EEPROM MOD_DEF(1) MOD_DEF(2) SFP module depending on SERDES 8 LOSS OF SINGAL (9,10,11,14) 6 MODULE DETECT 5 SCL 4 SDA 4.7K to 10K 4.7K to 10K Vcc 3.3V 4.7K to 10K PACKAGE DIAGRAM Units in mm Note: Specifications subject to change without notice. * OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 1/1/2008 V2.0 Optoway SPS-93120MG SPS-93120MG 5 * Revision History Version 1.0 2.0 Subject Initial datasheet Revise package diagram for high port density use Release Date 2005/12/1 2008/1/1 * OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail: sales@optoway.com.tw http: // www.optoway.com.tw 1/1/2008 V2.0