SPL-53-DR-IR1 OC-12/STM-4 GR-468 SFF-8472 SPL-53-DR-IR1-CDA SPL-53-DR-IR1-CNA

Preliminary SPL-53-DR-IR1 Features · Compliant with OC-3/STM-1 and OC-12/STM-4 Standards · Simplex LC connector

SFP Bi-Directional Transceiver Preliminary SPL-53-DR-IR1 SPL-53-DR-IR1 Features · Compliant with OC-3/STM-1 and OC-12/STM-4 OC-12/STM-4 Standards · Simplex LC connector · Single 3.3 V supply · 15 km reach · 13 dB Minimum Link Budget · 1550nm DFB Laser · Commercial temperature available (-Cxx) · Industrial temperature available (-Txx) · SFP MSA SFF-8074i compliant · Telcordia GR-468 GR-468 compliant · Digital Diagnostic SFF-8472 SFF-8472 compliant · Color coded bail latch: Yellow · RoHS compliant (lead free soldered) General operating Parameter Symbol Total Current Min. Typical Max. Unit Vcc Supply Voltage 3.135 3.3 3.465 V Icc - - 300 mA Power Supply Noise Rejectiona PSR 100 - - mVp-p Operating Temperature (-Cxx) Top -5 - 70 ºC Operating Temperature (-Txx) Top -40 - 85 ºC Storage Temperature Tst -40 - 85 ºC Data Rate OC-3/STM-1 DR - 155 - Mbps Data Rate OC-12/STM-4 OC-12/STM-4 DR - 622 - Mbps Data Rate Fast Ethernet DR - 125 - Mbps a) 20Hz to 155MHz Transmitter Specifications Parameter Symbol Min Typical Max Unit Optical Power POP -15 -11 -8 dBm Average Launch Power Of Off Tx POff - - -45 dBm Extinction Ratio ER 8.2 - - dB Eye Mask IEEE 802.3 and SONET/SDH Compliant Optical Rise Timeb tr Timeb tf - Optical Fall Mean Wavelength Spectral Width (RMS) Relative Intensity Noise Optical Crosstalk Side Mode Suppression Ratio Reflectance Tolerance RIN - 500 500 ps 1480 - 1580 nm - - 1 nm - Dispersion Penalty (at 15 Km) - ps 0.5 1 dB - - -120 dB/Hz XT - - -45 dB SMSR 30 - - dB rp -24 - - dB b) 20%-80% values LUMINENTOIC.COM 20550 Nordhoff St. · Chatsworth, CA 91311 · tel: 818.773.9044 · fax: 818.576.9486 9F, No 81, Shui Lee Rd. · Hsinchu, Taiwan, R.O.C. · tel: 886.3.5169222 · fax: 886.3.5169213 1 LUMNDS1689-Apr3007 Rev 0.1 SFP Bi-Directional Transceiver Preliminary SPL-53-DR-IR1 SPL-53-DR-IR1 Transmitter Specifications (Electical) Parameter Symbol Min Typical Rin 80 100 120 Vin,p-p 250 - 1200 mV Input Differential Impedence PECL Single Ended Data Input Swing TxFault_Fault Max Unit Vfault 2 - Vcc V Vnormal Vee - Vee+0.5 V TxDisable_Disable Vd 2 - Vcc V TxDisable_Enable Ven Vee - Vee+0.8 V Symbol Min Typical Max Unit TxFault_Normal Receiver Specifications Parameter Lowc Rsens,low - -30 -28 dBm Receive Power Highc Rsens,high -8 - - dBm Damage Threshold For Receiver Pin,damage - - 0 dBm 1260 - 1360 nm -38 - - dBm - - -28 dBm 0.5 - - dB - - -12 dB Receive Power Wavelength LOS Assert LOS De-assert LOS Hysteresis - Receiver Reflectance c) at 10-12 BER, FE unbalanced pattern, and 10-10 BER, 155.52 Mb/s & 622.08 Mb/s Electrical Output Parameter Symbol Min Typical Max Unit PECL Single Ended Data Output Swing Vout, p-p 185 - 800 mV Data Output Rise Time tr - - 500 ps Data Output Fall Time tf - - 500 ps Timing and Electrical Parameter Symbol Min Typical Max Unit t_on - - 1 ms Tx Disable Assert Time t_off - - 10 µs Time To Initialize, Including Reset Of Tx Fault t_init - - 300 ms Tx Disable Negate Time Tx Fault Assert Time t_fault - - 100 µs Tx Disable To Reset t_reset 10 - - µs t_loss_on - - 100 µs Los De-assert Time t_loss_off - - 100 µs Serial ID Clock Rate f_serial_clock - - 100 KHz 2 - - V Los Assert Time RX_LOS Voltage (High) RX_LOS Voltage (Low) LOS Output Voltage-Fault LOS Output Voltage-Normal - - 0.8 V VLOS fault 2 - Vcc V VLOSnormal Vee - Vee+0.5 V MOD_DEF (0:2)-High Vh 2 - Vcc V MOD_DEF (0:2)-LOW Vl Vee - Vee+0.5 V LUMINENTOIC.COM 20550 Nordhoff St. · Chatsworth, CA 91311 · tel: 818.773.9044 · fax: 818.576.9486 9F, No 81, Shui Lee Rd. · Hsinchu, Taiwan, R.O.C. · tel: 886.3.5169222 · fax: 886.3.5169213 2 LUMNDS1689-Apr3007 Rev 0.1 SFP Bi-Directional Transceiver Preliminary SPL-53-DR-IR1 SPL-53-DR-IR1 Diagnostics Range Accuracy Temperature (-Cxx) -5 to 70 ±3 ºC Internal 1/256 C Temperature (-Txx) -40 to 85 ±3 ºC Internal 1/256 C Tc(C)=Tad(16 bit signed twos complement)/256 Voltage 0 to Vcc 0.1 V Internal 100 µV V(Volts)=Vad(16 bit unsigned integer)*0.1 Bias current 0 to 120 5 mA External 0.002mA TX Power -15 to -8 ±2dB dBm External 0.1 µw TX_PWR(µW)=TX_PWRslope*TX_PWRad(16 bit unsigned integer +TX_PWRoffset RX Power -28 to -8 ±2dB dBm External 0.1 µw RX_PWR(µW)=A0+A1*x+A2*x^2+A3*x^3+A4*x^4 Parameter Unit Calibration Bit value Formula Tc(C)=Tad(16 bit signed twos complement)/256 I(mA)=Islope*Iad(16 bit unsigned integer)+Ioffset EEPROM Serial ID Address Description of Field Hex ASCII 20 Name of Field 4C L 21 E 4E N 54 T 4F O 29 49 I 30 43 C 37 00 38 06 39 B5 40 53 S 41 50 P 42 4C L 43 35 5 44 33 3 45 44 D 46 52 R 47 49 I 48 52 R 49 31 1 50 43 C 51 44 D 52 LUMINENTOIC.COM N 28 Part number in ASCII, e.g. SPL-53-DR-IR1-CDA SPL-53-DR-IR1-CDA 4E 45 27 Vendor PN I 25 IEEE vendor OUI code for LuminentOIC Inc. 49 26 Vendor OUI M 24 Vendor Name U 4D 23 SFP Vendor name(ASCII) 55 22 41 A 20550 Nordhoff St. · Chatsworth, CA 91311 · tel: 818.773.9044 · fax: 818.576.9486 9F, No 81, Shui Lee Rd. · Hsinchu, Taiwan, R.O.C. · tel: 886.3.5169222 · fax: 886.3.5169213 3 LUMNDS1689-Apr3007 Rev 0.1 SFP Bi-Directional Transceiver Preliminary SPL-53-DR-IR1 SPL-53-DR-IR1 Pin Function Notes 1 VeeT TX Ground 2 TX_FAULT Open Collector 3 TX_DISABLE Internally Pulled High 4 MOD_DEF2 Serial Data Input 5 MOD_DEF1 Serial Clock Input 6 MOD_DEF0 Internally Grounded 7 NC Not Connected 8 LOS Open Collector 9 VeeR RX Ground 10 VeeR RX Ground 11 VeeR RX Ground 12 RXD- RX Data Negative 13 RXD+ RX Data Positive 14 VeeR RX Ground 15 VccR RX Power 16 VccT TX Power 17 VeeT TX Ground 18 TXD+ TX Data Positive 19 TXD- TX Data Negative 20 VeeT TX Ground LUMINENTOIC.COM 20550 Nordhoff St. · Chatsworth, CA 91311 · tel: 818.773.9044 · fax: 818.576.9486 9F, No 81, Shui Lee Rd. · Hsinchu, Taiwan, R.O.C. · tel: 886.3.5169222 · fax: 886.3.5169213 4 LUMNDS1689-Apr3007 Rev 0.1 SFP Bi-Directional Transceiver Preliminary SPL-53-DR-IR1 SPL-53-DR-IR1 Outline drawing Units in mm (inches) LUMINENTOIC.COM 20550 Nordhoff St. · Chatsworth, CA 91311 · tel: 818.773.9044 · fax: 818.576.9486 9F, No 81, Shui Lee Rd. · Hsinchu, Taiwan, R.O.C. · tel: 886.3.5169222 · fax: 886.3.5169213 5 LUMNDS1689-Apr3007 Rev 0.1 SFP Bi-Directional Transceiver Preliminary SPL-53-DR-IR1 SPL-53-DR-IR1 Suggested Transceiver Interface 1H Vcc 10F 1H 0.1F VCCT .01F Protocol IC R1 LuminentOIC SFP 10K TX_DISABLE TX_DISABLE TX_FAULT TX_FAULT TD + SerDes Laser Driver .01F 100 TD VEET .01F VCCR 10F 0.1F RD + Receiver Amplifier .01F 100 RD - RX_LOS RX_LOS Vcc R VEER 1 R1 R1 .01F EEPROM R1 MOD_DEF 2 MOD_DEF 1 MOD_DEF 0 R1=4.7K to 10K LUMINENTOIC.COM 20550 Nordhoff St. · Chatsworth, CA 91311 · tel: 818.773.9044 · fax: 818.576.9486 9F, No 81, Shui Lee Rd. · Hsinchu, Taiwan, R.O.C. · tel: 886.3.5169222 · fax: 886.3.5169213 6 LUMNDS1689-Apr3007 Rev 0.1 SFP Bi-Directional Transceiver Preliminary SPL-53-DR-IR1 SPL-53-DR-IR1 Ordering Information Available Options: SPL-53-DR-IR1-CDA SPL-53-DR-IR1-CDA SPL-53-DR-IR1-CNA SPL-53-DR-IR1-CNA SPL-53-DR-IR1-TDA SPL-53-DR-IR1-TDA SPL-53-DR-IR1-TNA SPL-53-DR-IR1-TNA Part numbering Definition: SPL - 53 - DR - IR1 - Temperature Diagnostic Revision · SPL = LC connector · 53 = Tx 1550nm/Rx 1310nm · DR = Dual Rate 155M/622M 155M/622M · IR1 = Reach 15 km · Operating Temperature C = Commercial temperature (-5 to 70ºC) T = Industrial temperature (-40 to 85ºC) · D = Digital Diagnostic (SFF-8472 SFF-8472) N = No Diagnostic · Design Revision A = RoHS compliant (lead free soldered) Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC's sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company's standard one-year warranty; however, specifications designated as "preliminary" are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company's Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. · Chatsworth, CA 91311 · tel: 818.773.9044 · fax: 818.576.9486 9F, No 81, Shui Lee Rd. · Hsinchu, Taiwan, R.O.C. · tel: 886.3.5169222 · fax: 886.3.5169213 7 LUMNDS1689-Apr3007 Rev 0.1