SPD-8A115 115VAC/150VDC -217F P4855-1A 115VAC - Datasheet Archive

 

SEMICONDUCTOR SPD-8A115 Technical Data Datasheet 4119, Rev. B AC/DC Solid State Power Controller Module Description: The Solid

 

SENSITRON SEMICONDUCTOR SPD-8A115 SPD-8A115 Technical Data Datasheet 4119, Rev. B AC/DC Solid State Power Controller Module Description: The Solid State Power Controller (SSPC) Module is a microcontroller based Solid State Relay, designed to be used in Aircraft or Navy in 115VAC/150VDC 115VAC/150VDC applications. This module has integrated current sensing and over current / over temp protection. The module is equivalent to a DPST relay with a common single side isolated control. Compliant Documents & Standards: MIL-STD -167-1 (1) 19 June 1987 MIL-STD -217F -217F Notice 2 28 Feb 1995 P4855-1A P4855-1A January 1989 Mechanical Vibrations of Shipboard Equipment Reliability Prediction of Electronic Equipment Navy Power Supply Design and Reliability Guidelines (NAVMAT) Module Features: · · · · Epoxy Shell Construction Solid State Reliability; Low Weight (60 gms) - High Power Density Similar footprint as a mechanical relay: 2.8"x1.15"x1.15" Single-in-line pins to ease pcb assembly Electrical Features: · · · · · · · · · · · · · · · · · 115VAC 115VAC Input: Current rating of 8A with very low drop; 180mV typ Current rating upto 12A with drop @ 280mV 2 Advanced TRUE I t algorithm to compensate for different current waveforms 2-Pole operation: 500V DC isolation between poles High control circuit isolation: 1500V DC to either pole Cross-trip feature: Fault on one pole trips the other within 10µsec Very low control current: 14 mA @ 24V typ 2 True I t Protection from 11A to 90A Instant Trip Protection (3µsec typ) for loads over 100A High Overload Capability up to 250A; Repetitive Fault handling capability Built-in Transient Voltage Suppressor to handle Short Circuit Turn-Off Spikes o Over-temperature Protection: 75 C Amb typ Internally generated isolated supply to drive the switch Opto Isolated Control Signal input and Status output Soft Turn-on to reduce EMC issues Module Reset with a Low Level Signal; Trip Reset Circuit is Trip-Free Built-in Hysteresis and Noise Filtering to avoid nuisance Turn-ON/OFF · 221 West Industry Court 3 Deer Park, NY 11729-4681 3 Phone (631) 586 7600 Fax (631) 242 9798 · · World Wide Web - http://www.sensitron.com · E-Mail Address - sales@sensitron.com · SENSITRON SEMICONDUCTOR SPD-8A115 SPD-8A115 Technical Data Datasheet 4119, Rev. B Electrical Characteristics Control & Status Vcc Control Vcc Current (from +24V) Alarm Out Signal Control signal Reset 24V DC Nominal 20V to 36V DC 14 mA typ 20 mA max ON: High (internal pull-up to +24V); Output can source upto 5 mA OFF: Logic Low Output shall remain below 2V sink upto 5 mA ON: Logic Low (internal pull-up to +24V) Turns ON when input is pulled below 4V Input current @ Control pin < 0.5 mA OFF: Open Turns OFF when input is float or pulled above 12V Thro cycling of Control signal Thro cycling of Vcc Power Input Voltage Power Dissipation Current (Pole #1 and Pole #2) Max Voltage Drop (Each Pole) Turn ON time (measured from Input Signal) Turn OFF time (measured from Input Signal) Time Difference at Turn-on between Poles Time Difference at Turn-off between Poles Min Trip current (Each Pole) Trip time 11A 20A 30A 50A 90A 100A and above Repetitive Fault current Rating Output Rise Time (turn ON) Output Fall Time under normal turn-off Output Fall Time under Fault Min Load Requirement 0 to 170V DC 0 to 120V AC 10 Hz to 440 Hz < 2.5W @ 8A @ 70°C Amb per pole 8A Continuous 250A for 2 µsec o 180 mV typ @ 8A, TA = 25 C o o 260 mV max TA = -40 C ~ 70 C 3 msec max Both Poles turn-on together 50 µsec max Both Poles turn-off together 20 µsec max 20 µsec max 8.8A DC 8.8A AC RMS 460 msec ~ 860 msec 140 msec ~ 260msec 62 msec ~ 115 msec 22 msec ~ 42 msec 7 msec ~ 13 msec Less than 3 µsec 250A 5 µsec typ 300 nsec typ 300 nsec typ Nil · 221 West Industry Court 3 Deer Park, NY 11729-4681 3 Phone (631) 586 7600 Fax (631) 242 9798 · · World Wide Web - http://www.sensitron.com · E-Mail Address - sales@sensitron.com · SENSITRON SEMICONDUCTOR SPD-8A115 SPD-8A115 Technical Data Datasheet 4119, Rev. B Protection Short Circuit Protection Voltage Spikes OTP (Over Temperature Protection) threshold OTP response time Upto 250A Built-in Transient Voltage Suppressor to handle short-circuit turn-off spike o o o typ. 75 C, min. 70 C, max 80 C typ. 5 sec Physical Characteristics Temperature Operating Temperature Storage Temperature TA = -40°C to +70°C TA = -55°C to +85°C Environmental Altitude Case Dimensions Operating Orientation Weight MTBF (Estimate: MIL STD 217F) Upto 30,000 ft Can be installed in an unpressurized area 2.8"L x 1.15"W x 1.15"H Any 60 grams typ 100,000 hrs at 25°C Full load Mechanical Dimensions (in Inches) · 221 West Industry Court 3 Deer Park, NY 11729-4681 3 Phone (631) 586 7600 Fax (631) 242 9798 · · World Wide Web - http://www.sensitron.com · E-Mail Address - sales@sensitron.com ·