NEW DATABASE - 350 MILLION DATASHEETS FROM 8500 MANUFACTURERS
NEW DATABASE - 350 MILLION DATASHEETS FROM 8500 MANUFACTURERS
UCC2800/2801/2802/2803/2804/2805EP SGLS135C UC3842 UC3842A UCC2800/1/2/3/4/5 - Datasheet Archive
LOWPOWER BICMOS CURRENTMODE PWM SGLS135C - SEPTEMBER 2002 - REVISED MARCH 2006 D Controlled Baseline D D D D D D D D D D D - One
UCC2800/2801/2802/2803/2804/2805EP UCC2800/2801/2802/2803/2804/2805EP LOWPOWER BICMOS CURRENTMODE PWM SGLS135C SGLS135C - SEPTEMBER 2002 - REVISED MARCH 2006 D Controlled Baseline D D D D D D D D D D D - One Assembly/Test Site, One Fabrication Site Extended Temperature Performance of -55°C to 125°C Enhanced Diminishing Manufacturing Sources (DMS) Support Enhanced Product Change Notification Qualification Pedigree ESD Protection Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) 100 µA Typical Starting Supply Current 500 µA Typical Operating Supply Current D D D D Operation to 1MHz Internal Soft Start Internal Fault Soft Start Internal Leading-Edge Blanking of the Current Sense Signal 1 Amp Totem-Pole Output 70 ns Typical Response from Current-Sense to Gate Drive Output 1.5% Tolerance Voltage Reference Same Pinout as UC3842 UC3842 and UC3842A UC3842A D PACKAGE (TOP VIEW) Component qualification in accordance with JEDEC and industry standards to ensure reliable operation over an extended temperature range. This includes, but is not limited to, Highly Accelerated Stress Test (HAST) or biased 85/85, temperature cycle, autoclave or unbiased HAST, electromigration, bond intermetallic life, and mold compound life. Such qualification testing should not be viewed as justifying use of this component beyond specified performance and environmental limits. COMP FB CS RC 1 8 2 7 3 6 4 5 REF VCC OUT GND description The UCC2800/1/2/3/4/5 UCC2800/1/2/3/4/5 family of high-speed, low-power integrated circuits contain all of the control and drive components required for off-line and dc-to-dc fixed frequency current-mode switching power supplies with minimal parts count. These devices have the same pin configuration as the UC2842/3/4/5 UC2842/3/4/5 family and also offer the added features of internal full-cycle soft start and internal leading-edge blanking of the current-sense input. The UCC2800/1/2/3/4/5 UCC2800/1/2/3/4/5 family offers choice of maximum duty cycle and critical voltage levels. Lower reference parts such as the UCC2803 UCC2803 and UCC2805 UCC2805 fit best into battery operated systems, while the higher reference and the higher UVLO hysteresis of the UCC2802 UCC2802 and UCC2804 UCC2804 make these ideal choices for use in off-line power supplies. PART NUMBER MAXIMUM DUTY CYCLE REFERENCE VOLTAGE TURN-ON THRESHOLD TURN-OFF THRESHOLD UCC2800 UCC2800 100% 5V 7.2 V 6.9 V UCC2801 UCC2801 50% 5V 9.4 V 7.4 V UCC2802 UCC2802 100% 5V 12.5 V 8.3 V UCC2803 UCC2803 100% 4V 4.1 V 3.6 V UCC2804 UCC2804 50% 5V 12.5 V 8.3 V UCC2805 UCC2805 50% 4V 4.1 V 3.6 V Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2006, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 1 UCC2800/2801/2802/2803/2804/2805EP UCC2800/2801/2802/2803/2804/2805EP LOWPOWER BICMOS CURRENTMODE PWM SGLS135C SGLS135C - SEPTEMBER 2002 - REVISED MARCH 2006 ORDERING INFORMATION ORDERABLE PART NUMBER PACKAGE TA TOP-SIDE MARKING SOP - D UCC2800QDREP UCC2800QDREP 2800EP 2800EP SOP - D Tape and reel UCC2801QDREP UCC2801QDREP 2801EP 2801EP SOP - D Tape and reel UCC2802QDREP UCC2802QDREP 2802EP 2802EP SOP - D Tape and reel UCC2803QDREP UCC2803QDREP 2803EP 2803EP SOP - D Tape and reel UCC2804QDREP UCC2804QDREP 2804EP 2804EP SOP - D -40°C to 125°C Tape and reel Tape and reel UCC2805QDREP UCC2805QDREP 2805EP 2805EP -55°C to 125°C SOP - D Tape and reel UCC2801MDREP UCC2801MDREP 2801EP 2801EP Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. block diagram Ordering Information UCC2 80 0 Q or M D R EP ENHANCED PLASTIC INDICATOR TAPE and REEL INDICATOR PACKAGE D = Plastic SOIC TEMPERATURE RANGE INDICATOR PRODUCT OPTION 0 through 5 2 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 UCC2800/2801/2802/2803/2804/2805EP UCC2800/2801/2802/2803/2804/2805EP LOWPOWER BICMOS CURRENTMODE PWM SGLS135C SGLS135C - SEPTEMBER 2002 - REVISED MARCH 2006 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) VCC voltage w . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 V VCC current w . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±1 A Output energy (Capacitive Load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 µJ Analog Inputs (FB, CS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to 6.3 V Power Dissipation at TA < +25_C (D package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.65 W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65_C to 150_C Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . 300_C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Unless otherwise indicated, voltages are reference to ground and currents are positive into and negative out of the specified terminals. w In normal operation VCC is powered through a current limiting resistor. Absolute maximum of 12 V applies when VCC is driven from a low impedance source such that ICC does not exceed 30 mA (which includes gate drive current requirement). electrical characteristics, TA = -40_C to 125_C for Q temp and TA= -55_C to 125_C for M temp, VCC = 10 V (see Note 1), RT = 100 k from REF to RC, CT = 330 pF from RC to GND, 0.1 F capacitor from VCC to GND, 0.1 F capacitor from VREF to GND and TA = TJ (unless otherwise stated) PARAMETER TEST CONDITIONS UCC280XQ UCC280XQ, UCC280XM UCC280XM UNITS MIN TYP MAX 4.925 5 5.075 3.94 4 4.06 Reference Section Output voltage TJ = 25_C, I = 0.2 mA Load regulation voltage UCC2800/01/02/04 UCC2800/01/02/04 I = 0.2 mA to 5 mA UCC2803/05 UCC2803/05 10 30 TJ = 25_C 2.5 mV 1.9 TJ = -40_C to 125_C and TJ = -55_C to 125_C V Line regulation voltage VCC = 10 V to clamp Total variation voltage See Note 5 Output noise voltage f = 10 Hz to 10 kHz, See Note 7 TJ = 25_C Long term stability 1000 hours, See Note 7 TA = 125_C UCC2800/01/02/04 UCC2800/01/02/04 UCC2803/05 UCC2803/05 Output short-circuit current 4.88 5 5.1 3.9 4 4.08 · DALLAS, TEXAS 75265 V 130 µV 5 -5 POST OFFICE BOX 655303 mV/V mV -35 mA 3 UCC2800/2801/2802/2803/2804/2805EP UCC2800/2801/2802/2803/2804/2805EP LOWPOWER BICMOS CURRENTMODE PWM SGLS135C SGLS135C - SEPTEMBER 2002 - REVISED MARCH 2006 electrical characteristics, TA = -40_C to 125_C for Q temp and TA= -55_C to 125_C for M temp, VCC = 10 V (see Note 1), RT = 100 k from REF to RC, CT = 330 pF from RC to GND, 0.1 F capacitor from VCC to GND, 0.1 F capacitor from VREF to GND and TA = TJ (unless otherwise stated) PARAMETER UCC280XQ UCC280XQ, UCC280XM UCC280XM TEST CONDITIONS MIN TYP UNITS MAX Oscillator Section UCC2800/01/02/04 UCC2800/01/02/04 Oscillator frequency Temperature stability 40 46 52 UCC2803/05 UCC2803/05 See Note 2 26 31 36 See Note 7 kHz 2.5% Amplitude peak-to-peak 2.25 Oscillator peak voltage 2.4 2.55 2.45 V V Error Amplifier Section COMP = 2.5 V Input voltage UCC2800/01/02/04 UCC2800/01/02/04 2.44 2.5 2.56 COMP = 2 V UCC2803/05 UCC2803/05 1.95 2 2.05 Input bias current -1 Open loop voltage gain 60 COMP sink current FB = 2.7 V, COMP = 1.1 V COMP source current FB = 1.8 V, COMP = REF - 1.2 V Gain bandwidth product See Note 7 1 80 0.3 -0.2 V µA db 3.5 -0.5 mA -0.8 mA 2 MHz PWM Section UCC2800/02/03 UCC2800/02/03 Minimum duty cycle 97% 99% 100% UCC2801/04/05 UCC2801/04/05 Maximum duty cycle 48% 49% 50% COMP = 0 V 0 Current Sense Section Gain See Note 3 1.1 1.65 1.8 V/V Maximum input signal COMP = 5 V, See Note 4 0.9 1 1.1 V 200 nA Input bias current -200 CS blank time 50 COMP to CS offset voltage 150 ns 1.55 1.68 V 0.45 CS = 0 V 100 1.42 Over-current threshold voltage 0.9 1.35 V Output Section (OUT) IOUT = 20 mA 0.4 IOUT = 200 mA All parts 0.35 0.9 IOUT = 50 mA, VCC = 5 V UCC2803/05 UCC2803/05 0.15 0.4 All parts 0.7 1.2 IOUT = -20 mA All parts 0.15 0.4 IOUT = -200 mA All parts 1 1.9 IOUT = -50 mA, VCC = 5 V High-level output voltage VSAT (VCC - OUT) 0.1 IOUT = 20 mA, VCC = 0 V Low-level output voltage All parts UCC2803/05 UCC2803/05 V V 0.4 0.9 Rise time CL = 1 nF 41 70 ns Fall time CL = 1 nF 44 75 ns 4 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 UCC2800/2801/2802/2803/2804/2805EP UCC2800/2801/2802/2803/2804/2805EP LOWPOWER BICMOS CURRENTMODE PWM SGLS135C SGLS135C - SEPTEMBER 2002 - REVISED MARCH 2006 electrical characteristics, TA = -40_C to 125_C for Q temp and TA= -55_C to 125_C for M temp, VCC = 10 V (see Note 1), RT = 100 k from REF to RC, CT = 330 pF from RC to GND, 0.1 F capacitor from VCC to GND, 0.1 F capacitor from VREF to GND and TA = TJ (unless otherwise stated) PARAMETER UCC280XQ UCC280XQ, UCC280XM UCC280XM TEST CONDITIONS MIN TYP UNITS MAX Undervoltage Lockout Section UCC2800 UCC2800 9.4 10.2 11.5 12.5 13.5 3.7 4.1 4.5 UCC2800 UCC2800 6.3 6.9 7.5 UCC2801 UCC2801 6.8 7.4 8 UCC2802/04 UCC2802/04 See Note 6 8.6 UCC2803/05 UCC2803/05 Stop threshold 7.8 UCC2802/04 UCC2802/04 See Note 6 7.2 UCC2801 UCC2801 Start threshold 6.6 7.6 8.3 9 UCC2803/05 UCC2803/05 V V 3.6 4 0.12 0.3 0.48 UCC2801 UCC2801 1.6 2 2.4 UCC2802/04 UCC2802/04 3.5 4.2 5.1 UCC2803/05 UCC2803/05 Start to stop hysteresis 3.2 UCC2800 UCC2800 0.2 0.5 0.8 4 10 ms V Soft Start Section COMP rise time FB = 1.8 V, Rise from 0.5 V to REF - 1 V Overall Section Start-up current VCC < Start Threshold 0.1 0.2 mA Operating supply current FB = 0 V, CS = 0 V 0.5 1 mA VCC internal zener voltage ICC = 10 mA, See Note 6 and Note 8 13.5 15 V 12 VCC internal zener voltage minus start threshold voltage See Note 6 UCC2802/04 UCC2802/04 0.5 1 NOTES: 1. Adjust VCC above the start threshold before setting at 10 V. 2. Oscillator frequency for the UCC2800 UCC2800, UCC2802 UCC2802 and UCC2803 UCC2803 is the output frequency. Oscillator frequency for the UCC2801 UCC2801, UCC2804 UCC2804 and UCC2805 UCC2805 is twice the output frequency. DVCOMP A= DVCS 3. Gain is defined by: 0 v VCS v 0.8 V. 4. Parameter measured at trip point of latch with Pin 2 at 0 V. 5. Total Variation includes temperature stability and load regulation. 6. Start Threshold, Stop Threshold and Zener Shunt Thresholds track one another. 7. Not production tested. 8. The device is fully operating in clamp mode as the forcing current is higher than the normal operating supply current. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 V 5 UCC2800/2801/2802/2803/2804/2805EP UCC2800/2801/2802/2803/2804/2805EP LOWPOWER BICMOS CURRENTMODE PWM SGLS135C SGLS135C - SEPTEMBER 2002 - REVISED MARCH 2006 detailed terminal descriptions COMP COMP is the output of the error amplifier and the input of the PWM comparator. Unlike other devices, the error amplifier in the UCC2800 UCC2800 family is a true, low output-impedance, 2 MHz operational amplifier. As such, the COMP terminal can both source and sink current. However, the error amplifier is internally current limited, so that one can command zero duty cycle by externally forcing COMP to GND. The UCC2800 UCC2800 family features built-in full cycle Soft Start. Soft Start is implemented as a clamp on the maximum COMP voltage. CS CS is the input to the current sense comparators. The UCC2800 UCC2800 family has two different current sense comparators: the PWM comparator and an over-current comparator. The UCC2800 UCC2800 family contains digital current sense filtering, which disconnects the CS terminal from the current sense comparator during the 100 ns interval immediately following the rising edge of the OUT pin. This digital filtering, also called leading-edge blanking, means that in most applications, no analog filtering (RC filter) is required on CS. Compared to an external RC filter technique, the leading-edge blanking provides a smaller effective CS to OUT propagation delay. Note, however, that the minimum non-zero On-Time of the OUT signal is directly affected by the leading-edge-blanking and the CS to OUT propagation delay. The over-current comparator is only intended for fault sensing, and exceeding the over-current threshold will cause a soft start cycle. FB FB is the inverting input of the error amplifier. For best stability, keep FB lead length as short as possible and FB stray capacitance as small as possible. ground (GND) GND is reference ground and power ground for all functions on this part. OUT OUT is the output of a high-current power driver capable of driving the gate of a power MOSFET with peak currents exceeding "750 mA. OUT is actively held low when VCC is below the UVLO threshold. The high-current power driver consists of FET output devices, which can switch all of the way to GND and all of the way to VCC. The output stage also provides a low impedance to overshoot and undershoot. This means that in many cases, external schottky clamp diodes are not required. 6 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 UCC2800/2801/2802/2803/2804/2805EP UCC2800/2801/2802/2803/2804/2805EP LOWPOWER BICMOS CURRENTMODE PWM SGLS135C SGLS135C - SEPTEMBER 2002 - REVISED MARCH 2006 detailed descriptions (continued) RC RC is the oscillator timing pin. For fixed frequency operation, set timing capacitor charging current by connecting a resistor from REF to RC. Set frequency by connecting timing capacitor from RC to GND. For the best perfomance, keep the timing capacitor lead to GND as short and direct as possible. If possible, use separate ground traces for the timing capacitor and all other functions. The frequency of oscillation can be estimated with the following equations: 1.5 R C UCC2803UCC2805 UCC2803UCC2805 : F + 1.0 R C UCC2800010204 UCC2800010204 : F + (1) where frequency is in Hz, resistance is in ohms, and capacitance is in farads. The recommended range of timing resistors is between 10k and 200k and timing capacitor is 100 pF to 1000 pF. Never use a timing resistor less than 10k. To prevent noise problems, bypass VCC to GND with a ceramic capacitor as close to the VCC pin as possible. An electrolytic capacitor may also be used in addition to the ceramic capacitor. voltage reference (REF) REF is the voltage reference for the error amplifier and also for many other functions on the IC. REF is also used as the logic power supply for high speed switching logic on the IC. When VCC is greater than 1 V and less than the UVLO threshold, REF is pulled to ground through a 5 k resistor. This means that REF can be used as a logic output indicating power system status. It is important for reference stability that REF is bypassed to GND with a ceramic capacitor as close to the pin as possible. An electrolytic capacitor may also be used in addition to the ceramic capacitor. A minimum of 0.1 µF ceramic is required. Additional REF bypassing is required for external loads greater than 2.5 mA on the reference. To prevent noise problems with high speed switching transients, bypass REF to ground with a ceramic capacitor close to the IC package. power (VCC) VCC is the power input connection for this device. In normal operation VCC is powered through a current limiting resistor. Although quiescent VCC current is very low, total supply current will be higher, depending on OUT current. Total VCC current is the sum of quiescent VCC current and the average OUT current. Knowing the operating frequency and the MOSFET gate charge (Qg), average OUT current can be calculated from: I OUT + Q g F. (2) POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 7 UCC2800/2801/2802/2803/2804/2805EP UCC2800/2801/2802/2803/2804/2805EP LOWPOWER BICMOS CURRENTMODE PWM SGLS135C SGLS135C - SEPTEMBER 2002 - REVISED MARCH 2006 PARAMETER MEASUREMENT INFORMATION Error Amplifier Gain/Phase Response Oscillator The UCC3800/1/2/3/4/5 UCC3800/1/2/3/4/5 oscillator generates a sawtooth waveform on RC. The rise time is set by the time constant of RT and CT. The fall time is set by CT and an internal transistor on-resistance of approximately 125. During the fall time, the output is off and the maximum duty cycle is reduced below 50% or 100% depending on the part number. Larger timing capacitors increase the discharge time and reduce the maximum duty cycle and frequency. Figure 1 Figure 2 UCC1803/05 UCC1803/05 VREF vs. VCC; ILOAD = 0.5 mA UCC1800/01/02/04 UCC1800/01/02/04 Oscillator Frequency vs. RT and CT Figure 3 8 Figure 4 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 UCC2800/2801/2802/2803/2804/2805EP UCC2800/2801/2802/2803/2804/2805EP LOWPOWER BICMOS CURRENTMODE PWM SGLS135C SGLS135C - SEPTEMBER 2002 - REVISED MARCH 2006 PARAMETER MEASUREMENT INFORMATION UCC1803/05 UCC1803/05 Oscillator Frequency vs RT and CT UCC1800/02/03 UCC1800/02/03 Maximum Duty Cycle vs Oscillator Frequency Figure 5 Figure 6 UCC1801/04/05 UCC1801/04/05 Maximum Duty Cycle vs Oscillator Frequency UCC1800 UCC1800 ICC vs Oscillator Frequency Figure 8 Figure 7 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 9 UCC2800/2801/2802/2803/2804/2805EP UCC2800/2801/2802/2803/2804/2805EP LOWPOWER BICMOS CURRENTMODE PWM SGLS135C SGLS135C - SEPTEMBER 2002 - REVISED MARCH 2006 PARAMETER MEASUREMENT INFORMATION UCC1805 UCC1805 ICC vs Oscillator Frequency Dead Time vs CT, RT = 100 kW Figure 9 Figure 10 COMP to CS Offset vs Temperature, CS = 0 V Figure 11 10 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 UCC2800/2801/2802/2803/2804/2805EP UCC2800/2801/2802/2803/2804/2805EP LOWPOWER BICMOS CURRENTMODE PWM SGLS135C SGLS135C - SEPTEMBER 2002 - REVISED MARCH 2006 MECHANICAL DATA D (R-PDSO-G*) PLASTIC SMALL-OUTLINE PACKAGE 8 PINS SHOWN 0.020 (0,51) 0.014 (0,35) 0.050 (1,27) 8 0.010 (0,25) 5 0.008 (0,20) NOM 0.244 (6,20) 0.228 (5,80) 0.157 (4,00) 0.150 (3,81) Gage Plane 1 4 0.010 (0,25) 0°- 8° A 0.044 (1,12) 0.016 (0,40) Seating Plane 0.010 (0,25) 0.004 (0,10) 0.069 (1,75) MAX PINS * 0.004 (0,10) 8 14 16 A MAX 0.197 (5,00) 0.344 (8,75) 0.394 (10,00) A MIN 0.189 (4,80) 0.337 (8,55) 0.386 (9,80) DIM 4040047/E 4040047/E 09/01 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15). Falls within JEDEC MS-012 MS-012 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 11 PACKAGE OPTION ADDENDUM www.ti.com 18-Jul-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty UCC2800QDREP UCC2800QDREP ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2801MDREP UCC2801MDREP ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2801QDREP UCC2801QDREP ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2802QDREP UCC2802QDREP ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2803QDREP UCC2803QDREP ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2804QDREP UCC2804QDREP ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2805QDREP UCC2805QDREP ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM V62/03624-01XE V62/03624-01XE ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM V62/03624-02XE V62/03624-02XE ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM V62/03624-03XE V62/03624-03XE ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM V62/03624-04XE V62/03624-04XE ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM V62/03624-05XE V62/03624-05XE ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM V62/03624-06XE V62/03624-06XE ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM V62/03624-07XE V62/03624-07XE ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 18-Jul-2006 provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw www.ti.com/telephony www.ti.com/video Wireless Mailing Address: Telephony Video & Imaging www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated