SF161 SF167 MIL-STD-202 SF162 SF163 SF164 SF165 SF166

THRU SF167 16.0 AMP SUPER FAST RECTIFIERS VOLTAGE RANGE 50 to 600 Volts CURRENT 16.0 Amperes FEATURES * Low forward voltage drop

SF161 SF161 THRU SF167 SF167 16.0 AMP SUPER FAST RECTIFIERS VOLTAGE RANGE 50 to 600 Volts CURRENT 16.0 Amperes FEATURES * Low forward voltage drop * High current capability * High reliability * High surge current capability * Good for switching mode application TO-220 3.8 f +.2 HOLE THRU .412 (10.5) MAX. .108 (2.75) .248 (6.3) MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Lead solderable per MIL-STD-202 MIL-STD-202, method 208 guranteed * Polarity: As Marked * Mounting position: Any .180 (4.6) .595 (15.1) MAX. .550 (14.0) .158 (4.0) MIN. MAX. .051 MAX. (1.3) .040 MAX. (1.0) .100 (2.54) .120 (3.05) PIN 1 + PIN 1 PIN 3 * Weight: 2.24 grams .050 (1.27) CASE PIN 2 PIN 3 CASE PIN 2 Negative CT Suffix "A" Positive CT Suffix "C" Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current SF161 SF161 SF162 SF162 SF163 SF163 SF164 SF164 SF165 SF165 SF166 SF166 SF167 SF167 UNITS 50 35 50 100 70 100 150 105 150 200 140 200 .375"(9.5mm) Lead Length at Tc=125 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 8.0A Maximum DC Reverse Current Tc=25 C at Rated DC Blocking Voltage Tc=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG NOTES: 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 300 210 300 400 280 400 600 420 600 A 16.0 125 1.50 1.30 0.95 10 500 35 50 -65 50 +150 V V V A V A A nS pF C RATING AND CHARACTERISTIC CURVES (SF161 SF161 THRU SF167 SF167) FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE FIG.1- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC trr 10W NONINDUCTIVE ( ) D.U.T. 25Vdc (approx.) | | | | | | | | +0.5A (+) PULSE GENERATOR (NOTE 2) ( ) AVERAGE FORWARD CURRENT,(A) 50W NONINDUCTIVE 0 -0.25A (+) 1W NONINDUCTIVE OSCILLISCOPE (NOTE 1) -1.0A NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. 1cm 2. Rise Time= 10ns max., Source Impedance= 50 ohms. 24 20 16 Single Phase 12 Half Wave 60Hz Resistive Or Inductive Load 8 4 0 SET TIME BASE FOR 0 25 50 75 100 125 150 175 CASE TEMPERATURE,( C) 50 / 10ns / cm FIG.3-TYPICAL FORWARD FIG.4-TYPICAL REVERSE CHARACTERISTICS CHARACTERISTICS 1000 REVERSE LEAKAGE CURRENT, ( A) 10 7 SF 16 SF1 64 61~ SF 165 1.0 ~S F1 66 3.0 SF1 INSTANTANEOUS FORWARD CURRENT,(A) 50 Tj=25 C Pulse Width 300us 1% Duty Cycle 0.1 .01 .4 .6 .8 1.0 1.2 1.4 1.6 100 Tc=100 C 10 Tc=25 C 1.0 0.1 1.8 20 40 60 80 100 120 140 FIG.6-TYPICAL JUNCTION CAPACITANCE FIG.5-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 175 125 JUNCTION CAPACITANCE,(pF) PEAK FORWARD SURGE CURRENT,(A) 0 PERCENT OF RATED PEAK REVERSE VOLT AGE,(%) FORWARD VOLT AGE,(V) 100 75 Tj=25 C 8.3ms Single Half Sine Wave 50 JEDEC method 25 150 125 100 75 50 25 0 0 1 5 10 NUMBER OF CYCLES AT 60Hz 50 100 .01 .05 .1 .5 1 REVERSE VOLTAGE,(V) 5 10 50 100