TS-S99D017A SCM7362-XC TA-NWT-000253 SCM7362-XC-W ZBF253D-00 21CFR

Date : July 1999 Technical Specification for Optical Transceiver Module SCM7362-XC 155.52Mb/s 622.08Mb/s other _ Short Haul

Specification : TS-S99D017A TS-S99D017A Date : July 1999 Technical Specification for Optical Transceiver Module SCM7362-XC SCM7362-XC 155.52Mb/s 622.08Mb/s other _ Short Haul Intermediate Reach other _ Single 5.0 V Long Haul Long Reach Single 3.3 V other _ 1.3 µm 1.55 µm other _ Transmitter Receiver Transceiver ( 2R / 3R ) ( 2R / 3R ) SUMITOMO Electric reserves the right to make changes in the specification described hereinafter without prior notice. #Safety Precaution Symbols This specification uses various picture symbols to prevent possible injury to operator or other persons or damage to properties for appropriate use of the product. The symbols and definitions are as shown below. Be sure to be familiar with these symbols before reading this specification. Warning Caution Wrong operation without following this instruction may lead to human death or serious injury. Wrong operation without following this instruction may lead to human injury or property damage. Example of picture symbols indicates prohibition of actions. Action details are explained nearby. indicates compulsory actions or instructions. Action details are explained near by. (SCM7362-XC SCM7362-XC) -1/8- Specification : TS-S99D017A TS-S99D017A Date : July 1999 1. General SCM7362-XC SCM7362-XC is a series of compact and high speed performance digital optical transceiver module ideally designed for versatile high speed network applications. 1500nm high speed InGaAsP DFB-LD and InGaAs PIN-PD are provided as a light source and a detector, respectively. Transceiver module has PC board mountable package with electrical and optical interfaces. * Data Rate * Duty Cycle * Power Supply Voltage * Electrical Interface * Fiber Coupled Power * Sensitivity * Connector Interface 622.08 Mbps, NRZ 50% Single +3.3V ECL(Data, Clock), C-MOS(SD) -3 ~ +2dBm for SMF -8 ~ -28dBm SC Duplex Connector The features of SCM7362-XC SCM7362-XC are listed below. * Features Low Power Supply Voltage / Low Power Consumption Plastic Molded Package Multi-sourced Footprint Transmitter. Uncooled Laser with Automatic Power Control IC Optical Output Shut-down ( Disable ) Laser Bias Current Monitor / Rear Facet Monitor Class 1 Laser Product (IEC 825-1 and FDA 21 CFR 1040.10 and 1040.11) Receiver. Wide Dynamic Range Built-in Clock Recovery (including SAW filter) ITU-T G.957 / G.958 and Bellcore TA-NWT-000253 TA-NWT-000253 Compliant Signal Detect (SD) Function 2. Block Diagram Monitor Pin PD TD LD Modulation Circuit Data Input TDb Buffer Automatic Disable Buffer Reference Voltage Generator Bias Control Input Laser Power Circuit BM(Laser Bias Monitor) Circuit RFM(Rear Facet Monitor) Figure 1-1. Block Diagram (Transmitter) SAW Filter RD Vcc RDb 3R-IC PIN-PD RCLKb Pre-Amplifier SD Figure 1-2 Block Diagram (Receiver) (SCM7362-XC SCM7362-XC) RCLK -2/8- Specification : TS-S99D017A TS-S99D017A Date : July 1999 3. Package Dimension Caution Do not disassemble this product. Otherwise, failure, electrical shock overheating or fire may occur. Handle the lead pin carefully. Use assisting tools or prospective aids as required. A lead pin may injure skin or human body 4. Pin Assignment No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Symbol N/C N/C RCLKb RCLK BM(-) BM(+) Disable RFM(+) RFM(-) Veetx TD TDb Vcctx Vccrx FLAG(SD) RDb RD Veerx Function Non Connection (Internally) Non Connection (Internally) Differential Clock Output (Negative) Differential Clock Output (Positive) Monitoring pin for LD Bias Monitor Monitoring pin for LD Bias Monitor LD Disable Input Monitoring pin for Rear Facet Monitor Monitoring pin for Rear Facet Monitor Power Supply (-) for Transmitter : Connected to GND Transmitter Differential Data (Positive) Transmitter Differential Data (Negative) Power Supply (+) for Transmitter : Connected to +3.3V Power Supply (+) for Receiver : Connected to +3.3V FLAG (Signal Detect) Received Differential Data (Negative) Received Differential Data (Positive) Power Supply (-) for Receiver : Connected to GND NC pins should left open for additional functions in the future (SCM7362-XC SCM7362-XC) -3/8- Specification : TS-S99D017A TS-S99D017A Date : July 1999 5. Absolute Maximum Ratings Parameter Storage Case Temperature Operating Case Teperature Symbol Ts Tc Supply Voltage Input Voltage Lead Soldering (Temperature) (Time) min. -40 0 -40 0.0 Vee Vcc-Vee Vi Max 85 70 85 4.0 Vcc+0.5 260 10 Unit °C °C °C V V °C sec. Note 1 1, 2 1, 3 4 5 6 Note 1. No condensation allowed. 2. SCM7362-XC SCM7362-XC 3. SCM7362-XC-W SCM7362-XC-W 4. Vcc>Vee 5. TD, TDb, Disable 6. Measured on lead pin at 2mm (0.079in.) off the package bottom Warning Use the product with the rated voltage described in the specification. If the voltage exceeds the maximum rating, overheating or fire may occur. Caution Do not store the product in the area where temperature exceeds the maximum rating, where there is too much moisture or dampness, where there is acid gas or corrosive gas, or other extreme conditions. Otherwise, failure, overheating or fire may occur. 6. Electrical Interface ( Unless otherwise specified, Vcc-Vee = 3.14 to 3.47 V and all operating temperature shall apply. ) 6-1. Transmitter side Parameter Supply Voltage Supply Current Input Voltage High TD, TD Low Input Current High TD, TD Low Signal Input Rise / Fall Time Disable Input Voltage Disable Input Current LD Bias Monitor Voltage Rear Facet Monitor Voltage Symbol Vcc-Vee Idtx Vih Vil Iih Iil min. 3.14 Vcc-1.17 Vcc-1.95 -10 -10 Vdi Idi Vbm Vrfm Typ. 3.30 90 Vee+2.0 -10 0.01 0.01 Note 1. Output current is not included. 2. Measured at the bit rate of 622.08Mbps, 50% duty cycle data, 3.SCM7362-XC SCM7362-XC(Tc=0~70°C) 4.SCM7362-XC-W SCM7362-XC-W(Tc=-40~85°C) 5. Vcc=+3.3V, 6.Tc=25°C, 7. 20 ~ 80%, 8. The transmitter is enable as default state and requires an external voltage only to disable. 9. The Laser Bias and Rear Facet Monitor currents are calculated as raitos of the corresonding voltages to their current-sensing resistors,10 and 200, respectively(refer to Figure 3). Upon mesureing or utilizing these values, use a device whose input impedance is high enough(>1M) compared with those resistors. Max. 3.47 200 Vcc-0.73 Vcc-1.45 150 10 0.5 Vcc 200 0.50 0.20 Unit V mA V 1, 2, 3 4, 5 µA 4, 5 nsec. V µA V V Vcc Note 6 7 5, 8 5, 8 Vcc Laser Monitor PD 3k 15k Pin 6 Pin8 10 Pin 5 200 3k 15k Pin 9 Bias Circuit Figure 3 Monitor Circuit Schematic Diagram (SCM7362-XC SCM7362-XC) -4/8- Specification : TS-S99D017A TS-S99D017A Date : July 1999 6-2. Receiver side Parameter Symbol Vcc-Vee Idrx Data & Clock Output Voltage SD Output Voltage Clock Rise / Fall Time SD Assert Time SD deassert Time Data Rise / Fall Time Clock Sampling Point High Low High Low min. 3.14 Voh Vol Voh Vol Trc / Tfc Ta Td Trd / Tfd Tcsp Supply Voltage Supply Current Vcc-1.10 Vcc-1.86 2.40 0.00 0.80 Typ. 3.30 115 0.90 Max. 3.47 160 180 Vcc-0.86 Vcc-1.50 Vcc 0.40 700 1000 1000 1000 1.00 Unit V mA mA V Note V 4,6 4,7 8,9 psec. µsec µsec psec. nsec Note 1. Output current is not included. 2. SCM7362-XC SCM7362-XC (Tc=0 ~ 70°C), 3. SCM7362-XC-W SCM7362-XC-W (Tc=-40 ~ 85°C) 4. Vcc=+3.3V, Tc=25°C 5. Termination condition : RI= 50 to Vccrx =-2V 6. Output current Ioh =-200µA 7. Output current Iol = 2.1mA 8. 20~80% 9. Input capacitance and stray capacitance of measuring devices should be less tham 2pF 10. Phase difference between rising edge of RD and rising edge of RCLK. (Please refer to Figure 4) Ta Td Optical Input SD Output (Positive) RD Output (Positive) RCLK Output (Positive) Tcsp Figure 4. Timing Chart (SCM7362-XC SCM7362-XC) -5/8- 1,2 1,3 4 8,9 10 Specification : TS-S99D017A TS-S99D017A Date : July 1999 7. Optical Interface ( Unless otherwise specified, Vcc-Vee = 3.14 to 3.47 V and all operating temperature shall apply. ) 7-1. Transmitter side Parameter Average Output Power Extinction Ratio Center Wavelength Spectral Width (-20dB Width) Symbol Po Er c Side Mode Suppression Raito Eye Mask for Optical Output Sr min. -3.0 10.0 1480 Typ. Max. 2.0 1580 1.0 30.0 Compliant with ITU-T recommendation G.957 Unit dBm dB nm nm Note 1 1 dB Note 1. Measured at 622.08Mbps PRBS2^23-1, 50% duty cycle data Relation between Input Signal and Optical Output Signal Input Signal TD Optical Output Siganl TDb High Low ON (High) Low High OFF (Low) High High Undefined Low Low Undefined Warning Do not look at the laser beam projection area (e.g. end of optical connector) with naked eyes or through optical equipment while the power is supplied to this product. Otherwise, your eyes may be injured. 7-2. Receiver side Parameter Bit Rate Range Minimum Sensitivity Overload Clock Jitter(rms) Clock Duty Data Jitter(rms) Consecutive Identical Digit SD Assert Level SD deassert Level Max. Receiver Reflextance Symbol Pmin Pmax Tjc Cduty Tjd CID Pa Pd - min. Typ. 622.08 +/- 50ppm -33.0 Max. -28.0 -8.0 45.0 50.0 72 -50 -50 100 -36.5 -37.5 16.0 55.0 40.0 -28 -28 -14 Unit Mbps nm nm psec % psec bits dBm dBm dB Note 1. BER=10^-10 2. Measured at the bit rate of 622.08Mbps, PRBS 2^23-1, NRZ 3. Optical Input Power: -28.0 ~ -8.0dBm, 4.Termination condition for RD, RDb, RCLK and RCLKb : RI=50 to Vccrx-2V. 8. Relation between Disable Input Voltage and Optical Output Power Disable Input Voltage "L" (0[v] ~ 0.8[v]) "H" (2.0[v] ~ VCCTX) Optical Output Power Enabled Disabled (