TS-S00D028C SCM6111 SCM6111-GL-ZN SCM6111-GL-CN SCM6111-GL-DN SCM6111-GL-ZW - Datasheet Archive

 

March, 2002 Technical Specification for Optical Transceiver Module SCM6111 155.52Mb/s 622.08Mb/s other _ Short Haul Intermediate

 

Specification : TS-S00D028C TS-S00D028C March, 2002 Technical Specification for Optical Transceiver Module SCM6111 SCM6111 155.52Mb/s 622.08Mb/s other _ Short Haul Intermediate Reach other _ Single 5.0 V Long Haul Long Reach Single 3.3 V 1.3 µm 1.55 µm other _ Transmitter Receiver Transceiver ( 2 X 10 ) ( 2R / 3R ) other _ ( 2R / 3R ) Applicable Part Numbers : SCM6111-GL-ZN SCM6111-GL-ZN, SCM6111-GL-CN SCM6111-GL-CN, SCM6111-GL-DN SCM6111-GL-DN SCM6111-GL-ZW SCM6111-GL-ZW, SCM6111-GL-CW SCM6111-GL-CW, SCM6111-GL-DW SCM6111-GL-DW SCM6111-JL-ZN SCM6111-JL-ZN, SCM6111-JL-CN SCM6111-JL-CN, SCM6111-JL-DN SCM6111-JL-DN SCM6111-JL-ZW SCM6111-JL-ZW, SCM6111-JL-CW SCM6111-JL-CW, SCM6111-JL-DW SCM6111-JL-DW Sumitomo Electric reserves the right to make changes in this specification without prior notice. #Safety Precaution Symbols This specification uses various picture symbols to prevent possible injury to operator or other persons or damage to properties for appropriate use of the product. The symbols and definitions are as shown below. Be sure to be familiar with these symbols before reading this specification. Warning Caution Wrong operation without following this instruction may lead to human death or serious injury. Wrong operation without following this instruction may lead to human injury or property damage. Example of picture symbols indicates prohibition of actions. Action details are explained thereafter. indicates compulsory actions or instructions. Action details are explained thereafter. (SCM6111 SCM6111) - 1 / 16- Specification : TS-S00D028C TS-S00D028C March, 2002 1. General Features of SCM6111 SCM6111 are listed below. * SDH STM-1 L-1.1 / SONET OC-3 LR-1 Compliant * Power Supply Voltage Single +3.3V * Compact Package Size 49.0 X 13.59 X 9.8 mm * Electrical Interface LVPECL for DATA, LVTTL for Signal Detect and Laser Disable * Fiber Coupled Power -5 ~ 0dBm (Typ. -2dBm) into SMF * Input Power Range -8 ~ -34dBm (Typ. Sensitivity -35dBm) * Monitor Functions Laser Bias Monitor, Rear Facet Monitor * Laser Disable Function * Signal Detect (SD) Function * Connector Interface LC Duplex Receptacle 2. Block Diagram Monitor PIN PD TD LD Modulation Circuit Data Input TDb Buffer Automatic Power Control Input Tdis Buffer Reference Voltage Generator Laser Bias Circuit Bmon+ (Laser Bias Monitor) Bmon- Pmon+ Circuit (Rear Facet Monitor) Pmon- Figure 1. Block Diagram (Transmitter) PLL RD VpdR RDb 3R-IC PIN PD RCLK RCLKb Pre-Amplifier SD Figure 2. Block Diagram (Receiver) Caution Do not disassemble this product. Otherwise, failure, electrical shock, overheating or fire may occur. Handle the lead pins carefully. Use assisting tools or prospective aids as required. A lead pin may injure skin or human body (SCM6111 SCM6111) - 2 / 16- Specification : TS-S00D028C TS-S00D028C March, 2002 3. Package Dimension 3.1 SCM6111-GL- SCM6111-GL-## ( With Housing Leads ) All dimensions are in mm. Figure 3. Outline Dimensions (SCM6111-GL-Z SCM6111-GL-Z#) EMI finger (Type-C) Type-C EMI finger is an option for transceivers to be used on the card-edge with the receptacle protruding through a panel opening. It has fingers on three sides to make electrical contact with the sides of the bezel opening for grounding purpose. Figure 4. Outline Dimensions (SCM6111-GL-C SCM6111-GL-C#) (SCM6111 SCM6111) - 3 / 16- Specification : TS-S00D028C TS-S00D028C March, 2002 All dimensions are in mm. EMI finger (Type-D) Type-D EMI finger is an option for transceivers to be used on the card-edge with the receptacle protruding through a panel opening. It has fingers on four sides to make electrical contact with the sides of the bezel opening for grounding purpose. Figure 5. Outline Dimensions (SCM6111-GL-D SCM6111-GL-D#) (SCM6111 SCM6111) - 4 / 16- Specification : TS-S00D028C TS-S00D028C March, 2002 3.2 SCM6111-JL- SCM6111-JL-## ( Without Housing Leads ) All dimensions are in mm. Figure 6. Outline Dimensions (SCM6111-JL-Z SCM6111-JL-Z#) EMI finger (Type-C) Type-C EMI finger is an option for transceivers to be used on the card-edge with the receptacle protruding through a panel opening. It has fingers on three sides to make electrical contact with the sides of the bezel opening for grounding purpose. Figure 7. Outline Dimensions (SCM6111-JL-C SCM6111-JL-C#) (SCM6111 SCM6111) - 5 / 16- Specification : TS-S00D028C TS-S00D028C March, 2002 All dimensions are in mm. EMI finger (Type-D) Type-D EMI finger is an option for transceivers to be used on the card-edge with the receptacle protruding through a panel opening. It has fingers on four sides to make electrical contact with the sides of the bezel opening for grounding purpose. Figure 8. Outline Dimensions (SCM6111-JL-D SCM6111-JL-D#) (SCM6111 SCM6111) - 6 / 16- Specification : TS-S00D028C TS-S00D028C March, 2002 Figure 9. Recommended Footprint 0.92 +/- 0.20 2.12 +/- 0.20 11.32 +/- 0.20 6.17 +/- 0.20 4.78 +/- 0.20 +/- 0.20 2.08 +/- 0.20 18.49 : Conductive area 7654321 7654321 7654321 7654321 7654321 Unit : mm Figure 10. Package Bottom View (SCM6111 SCM6111) - 7 / 16- 13.97 Min Pitch Specification : TS-S00D028C TS-S00D028C March, 2002 A 10.16 ± 0.10 A 13.25 Max 11.82 Min 15.9 Max Top of PCB SECTION A-A [Type-C finger] 13.97± 0.10 SECTION A-A [Type-D finger] Figure 11. Recommended Bezel Design for Systems Using SFF Transceivers (SCM6111 SCM6111) - 8 / 16- Specification : TS-S00D028C TS-S00D028C March, 2002 4. Pin Assignment No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol VpdR VeeR VeeR RCLKb RCLK VeeR VccR SD RDb RD VccT VeeT Tdis TD TDb VeeT BmonBmon+ PmonPmon+ I/O/P P P P O O P P O O O P P I I I P O O O O Level +3.3V DC GND GND LVPECL LVPECL GND +3.3V DC LVTTL LVPECL LVPECL +3.3V DC GND LVTTL/LVCMOS LVPECL LVPECL GND Description DC Bias Supply for Re ce ive r PIN-PD. Pow e r Supply (-) for Receiver. Pow e r Supply (-) for Receiver. Recovere d Clock Output. Inverted. Recovere d Clock Output. Non-inverted. Pow e r Supply (-) for Receiver. Pow e r Supply (+) for Re ce iver. Signal De tect. High level indicates presence of optical input signal (Active High). Inve rte d Re ce ive r Output Data. No internal terminations are provided. Non-Inverted Re ceive r Output Data. No internal terminations are provided. Pow e r Supply (+) for Trans m itte r. Pow e r Supply (-) for Transm itter. Transm itter Dis able (Active High). Def aults to logic 0 (enable TX) w hen left open. Non-Inverted Transm itter Input Data. Self biased. Not internally terminated. Inve rte d Trans m itte r Input Data. Self biased. Not internally terminated. Pow e r Supply (-) for Transm itter. LD Bias Curre nt M onitor. Voltage diff erence betw een pins 17 and 18 is proportional Analog Voltage to the laser bias current. Rear Facet M onitor. Transmitter output pow er can be monitored, in terms of rear Analog Voltage f acet monitor PD current, by measuring voltage dif ference betw een pins 19 and 20. N otes: 1. I/O/P stands f or signal input, signal output , and DC power/ bias supply , respectiv ely . 2. R ef er t o f igure 14 f or det ails of Bmon and Pmon outputs. Stand-O ff H ou sing Lead pin1 pin1 0 pin2 0 pin1 1 P IN PO UT Stud * Mounting Studs are provided for mechanical support to the circuit board. It is recommended that the holes in the circuit Stand-O ff board be connected to frame ground. * Housing Leads are internally connected to VeeR and VeeT. H ou sing Lead (SCM6111-JL- SCM6111-JL-## has no Housing Leads.) * Stand-Offs provide gap between the circuit board and the module to help escape residual water after aqueous wash. Figure 12. Bottom View 5. Absolute Maximum Ratings Parameter Storage Case Temperature Operating Case Teperature Symbol Ts Tc Supply Voltage Input Voltage Lead Soldering Conditions Vcc Vi min. -40 -5 -40 0.0 0 Temperature Time Max 85 70 85 4.0 Vcc+0.5 260 10 Unit °C °C V V °C sec. Note 1 2 3 4 5 Notes: 1. No condensation allowed. 2. SCM6111- SCM6111-#L-#N 3. SCM6111- SCM6111-#L-#W 4. TD, TDb, Tdis 5. Measured on lead pin at 2mm (0.079in.) off the package bottom Warning Use the product with the rated voltage described in the specification. If the voltage exceeds the maximum rating, overheating or fire may occur. Caution Do not store the product in the area where temperature exceeds the maximum rating, where there is too much moisture or dampness, where there is acid gas or corrosive gas, or other extreme conditions. Otherwise, failure, overheating or fire may occur. (SCM6111 SCM6111) - 9 / 16- Specification : TS-S00D028C TS-S00D028C March, 2002 6. Electrical Interface ( Unless otherwise specified, Vcc-Vee = 3.135 to 3.465 V and all operating temperature shall apply. ) 6-1. Transmitter side Parameter Supply Voltage Supply Current TD, TDb Input Voltage High Low TD, TDb Input Current High Low Signal Input Rise / Fall Time Tdis Input Voltage High Low Tdis Input Current High LD Bias Monitor Voltage Rear Facet Monitor Voltage Symbol Vcc-Vee Idtx Vih Vil Iih Iil min. 3.135 Vcc-1.17 Vcc-1.95 -10 -10 Vdi Vei Idi Vbm Vrfm 2.0 0.0 -10 0.01 0.01 Typ. 3.30 70 140 0.05 Notes: 1. Input current is not included. 2. 50% duty cycle data. 3. 155.52Mbps, PRBS2^23-1, NRZ. 4. Vcc=+3.3V 5. Tc=25°C 6. Input Terminal is biased internally, as shown in the figure13. 7. 20-80%. 8. LVTTL input.Refer to Section 8, "Relation between Disable Input Voltage and Optical Output Power", for detail. 9. The Laser Bias Monitor Current and Rear Facet Monitor Current are calculated as ratios between the corresponding voltages and current sensing resistors, 10 and 200, as shown in the figure 14. P in 1 8 TD/TDb R2 R2 R1 +R2 = 2.0 Figure 13. Internal Bias of Input Terminal (SCM6111 SCM6111) 3k µA 4, 5, 6 nsec. V V µA V V 7 8 2, 9 2, 9 M o n ito r 3k P in 1 7 B mon- APC C irc uit Figure 14. Bmon and Pmon Interface - 10 / 16- P in 2 0 P mon+ 200 3k 3k B ia s C irc uit 3.3 1, 2, 3 4, 5, 6 P IN -P D 1 0 R1R2 = 1.3k ( typ.) R1 +R2 Note V cc Vcc R1 Unit V mA V LD B mon+ LVPECL Max. 3.465 140 Vcc-0.73 Vcc-1.45 150 10 1.5 Vcc 0.8 200 0.50 0.50 P in 1 9 P mon- Specification : TS-S00D028C TS-S00D028C March, 2002 6-2. Receiver side Parameter Power Supply Voltages Power Supply Current RD, RDb, RCLK, RCLKb Low Output Voltage High SD Output Voltage Low High Output Transition Time Clock Sampling Point Clock Duty Cycle Output Clock Random Jitter Output Clock Jitter Peaking SD Assert Time SD Deassert Time Symbol VCC ICC VOL VOH tI TCSP JC JP Ta Td Min. 3.135 VCC-1.88 VCC-1.20 Vee 2.400 2.6 45 Typ. 3.3 - 3.1 1.3 2.3 2.3 Max. 3.465 200 VCC-1.62 VCC-0.83 0.800 Vcc 0.5 3.6 55 3.6 0.1 100 100 Unit V mA V V V V ns ns % deg rms dB µs µs Note 1 2, 3 2 4 5 6 Notes: 1. Output current is not included. 155.52Mbps, PRBS2^23-1, NRZ. 2. Vcc=+3.3V, Tc=25°C. 3. Rl=50 to Vcc-2V. 4. 20-80%. Input capacitance and stray capacitance of measuring devices should be less than 2pF. 5. Time difference between RD transition and rising edge of RCLK. Refer to Figure 15. 6. 155.52Mbps, PRBS2^23-1, NRZ. Td Ta Optical Input SD Output RD Output RCLK Output T CSP Figure 15. Timimg Chart (SCM6111 SCM6111) - 11 / 16- Specification : TS-S00D028C TS-S00D028C March, 2002 7. Optical Interface ( Unless otherwise specified, Vcc-Vee = 3.135 to 3.465 V and all operating temperature shall apply. ) 7-1. Transmitter side Parameter Average Output Power Extinction Ratio Center Wavelength Spectral Width (-20dB Width) Side Mode Suppression Ratio Eye Mask for Optical Output Symbol min. Typ. Max. Unit Po -5.0 -2.0 0.0 dBm Er 10 dB c 1280 1335 nm 1.0 nm Sr 30 dB Compliant with Bellcore GR-253 GR-253 CORE and ITU G.957 Note 1 1 Notes: 1. Measured at 155.52Mbps PRBS2^23-1 Normalized Amplitude 1.20 1.00 Relation between Input Signal and Optical Output Signal 0.80 Input Signal Optical Output Signal TD TDb High Low ON (High) 0.50 0.20 Low -0.20 0.00 0.15 0.35 0.65 OFF (Low) High Undefined Low 0.00 High High Low Undefined 0.85 1.00 Figure 16. Optical Pluse Mask with Fourth Order Bessel-Thomson Filter Specified in ITU-T G.957 Warning Do not look at the laser beam projection area (e.g. end of optical connector) with naked eyes or through optical equipment while the power is supplied to this product. Otherwise, your eyes may be injured. 7-2. Receiver side Parameter Optical Input Wavelength Minimum Sensitivity Overload SD Assert Level SD Deassert Level SD Hysteresis Symbol Pmin Pmax Pa Pd Phys min. 1260 Typ. -35.0 0.0 -45.0 -45.0 1.0 Max. 1580 -34.0 -34.0 -35.0 6.0 Unit nm dBm dBm dBm dBm dB Notes: 1. BER=10^-10 2. Measured at the bit rate of 155.52Mbps, PRBS 2^23-1, NRZ 8. Relation between Disable Input Voltage and Optical Output Power Tdis Input Voltage "L"(Vee ~ Vee+0.8V) "H"(Vee+2.0V ~ Vcc) Open (SCM6111 SCM6111) Optical Output Power Enabled Disabled (