LL-S11FSC-2S - Datasheet Archive

 

1.00mm Height 0802 Package With Right Lens Super Red Chip LED Technical Data Sheet Part No.: LL-S11FSC-2S Spec No.: S11F

 

Luckylight 1.00mm Height 0802 Package With Right Lens Super Red Chip LED Technical Data Sheet Part No.: LL-S11FSC-2S LL-S11FSC-2S Spec No.: S11F Approved: ZHOU Rev No.: V.3 Checked: Wu Lucky Light Electronics Co., Ltd. Date: Mar./18/2006 Drawn: Shu Page: 1 OF 9 http://www.luckylight.cn Luckylight Features: Package in 8mm tape on 7" diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. Mono-color type. The product itself will remain within RoHS compliant version. Descriptions: The S11F SMD LED is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. Besides, lightweight makes them ideal for miniature applications, etc. Applications: Automotive: Backlighting in dashboard and switch. Telecommunication: Indicator and backlighting in telephone and fax. Flat backlight for LCD, switch and symbol. General use. Spec No.: S11F Approved: ZHOU Rev No.: V.3 Checked: Wu Lucky Light Electronics Co., Ltd. Date: Mar./18/2006 Drawn: Shu Page: 2 OF 9 http://www.luckylight.cn Luckylight Package Dimension: 0.6 + Polarity 1.7±0.2 2.1±0.2 1±0.2 .5 0.5 R0 Recommended Soldering Pad Dimensions 2.2 0.5 1.5 Cathode Mark 0.9 1.3 0.9 Unit: mm Tolerance: ±0.10mm Part No. Chip Material Lens Color Source Color LL-S11FSC-2S LL-S11FSC-2S GaAlAs Water Clear Super Red Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ± 0.10mm (.004) unless otherwise specified. 3. Specifications are subject to change without notice. Spec No.: S11F Approved: ZHOU Rev No.: V.3 Checked: Wu Lucky Light Electronics Co., Ltd. Date: Mar./18/2006 Drawn: Shu Page: 3 OF 9 http://www.luckylight.cn Luckylight Absolute Maximum Ratings at Ta=25 Parameters Symbol Max. Unit Power Dissipation PD 60 mW Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) IFP 100 mA Forward Current IF 25 mA Reverse Voltage VR 5 V Operating Temperature Range Topr -40 to +80 Storage Temperature Range Tstg -40 to +85 Soldering Temperature Tsld 260 for 5 Seconds Electrical Optical Characteristics at Ta=25 Parameters Symbol Min. Luminous Intensity * Typ. Max. Unit Test Condition IV 6 12 - mcd IF=20mA (Note 1) 21/2 - 130 - Deg IF=20mA (Note 2) Peak Emission Wavelength p - 660 - nm IF=20mA Dominant Wavelength d - 640 - nm IF=20mA (Note 3) Spectral Line Half-Width - 45 - nm IF=20mA Forward Voltage VF 1.60 2.00 2.40 V IF=20mA Reverse Current IR - - 10 µA VR=5V Viewing Angle * Notes: 1. Luminous Intensity Measurement allowance is ± 10%. 2. 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength (d) is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Spec No.: S11F Approved: ZHOU Rev No.: V.3 Checked: Wu Lucky Light Electronics Co., Ltd. Date: Mar./18/2006 Drawn: Shu Page: 4 OF 9 http://www.luckylight.cn Luckylight Typical Electrical / Optical Characteristics Curves (25 Ambient Temperature Unless Otherwise Noted) Forward Current & Forward Voltage Ta=25 Ta=25 Forward Current IF (mA) 100 75 50 25 0 300 1000 400 500 600 700 Wavelength p (nm) Luminous Intensity & Ambient Temperature 100 10 1 -60 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta () 50 40 30 20 10 0 800 1.6 1.8 2.0 2.2 2.4 2.6 Forward Voltage VF (V) Luminous Intensity & Forward Current Relative Luminous Intensity (%) Relative Luminous Intensity (%) Relative Luminous Intensity (%) Spectrum Distribution f=1KHz Duty=1/10 100 10 1 0 10 Forward Current Derating Curve Forward Current IF (mA) Ta=25 1000 1 2 3 10 10 10 Forward Current IF (mA) Radiation Diagram 50 o 0 o 10 Ta=25 o 20 o 30 40 o 40 30 25 20 1.0 0.9 o 0.8 10 0 o 50 0.7 0 Spec No.: S11F Approved: ZHOU 20 40 60 80 100 Ambient Temperature Ta () Rev No.: V.3 Checked: Wu Lucky Light Electronics Co., Ltd. 0.5 0.3 0.1 0 0.2 0.4 0.6 Date: Mar./18/2006 Drawn: Shu 60 o 70 o 80o 90 Page: 5 OF 9 http://www.luckylight.cn Luckylight Reliability Test Items And Conditions: The reliability of products shall be satisfied with items listed below: Confidence level: 90%. LTPD: 10%. 1) Test Items and Results: No. Test Item Test Hours/Cycles Test Conditions Sample Size Ac/Re 1 Resistance to Soldering Heat 6 Min Tsld=260±5, Min. 5sec 25pcs 0/1 2 Thermal Shock 300 Cycles H: +100 5min 10 sec L: -10 5min 25pcs 0/1 300 Cycles H: +100 15min 5min L: -40 15min 25pcs 0/1 1000Hrs. Temp: 100 25pcs 0/1 1000Hrs. IF=20mA 25pcs 0/1 1000Hrs. Temp: -40 25pcs 0/1 1000Hrs. 85/85%RH 25pcs 0/1 3 4 5 6 7 Temperature Cycle High Temperature Storage DC Operating Life Low Temperature Storage High Temperature/ High Humidity 2) Criteria for Judging the Damage: Criteria for Judgment Item Symbol Test Conditions Min Max Forward Voltage VF IF=20mA - F.V.*)×1.1 Reverse Current IR VR=5V - F.V.*)×2.0 Luminous Intensity IV IF=20mA F.V.*)×0.7 - *) F.V.: First Value. Spec No.: S11F Approved: ZHOU Rev No.: V.3 Checked: Wu Lucky Light Electronics Co., Ltd. Date: Mar./18/2006 Drawn: Shu Page: 6 OF 9 http://www.luckylight.cn Luckylight Reel Dimensions: Carrier Tape Dimensions: Loaded quantity 3000 PCS Per reel. Spec No.: S11F Approved: ZHOU Rev No.: V.3 Checked: Wu Lucky Light Electronics Co., Ltd. Date: Mar./18/2006 Drawn: Shu Page: 7 OF 9 http://www.luckylight.cn Luckylight Please read the following notes before using the product: 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture adsorbent material (silica gel) has fabled away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment: 60±5 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile. 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 260 for 5 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. Spec No.: S11F Approved: ZHOU Rev No.: V.3 Checked: Wu Lucky Light Electronics Co., Ltd. Date: Mar./18/2006 Drawn: Shu Page: 8 OF 9 http://www.luckylight.cn Luckylight 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 6. Caution in ESD Static Electricity and surge damages the LED. It is recommended to use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded. Spec No.: S11F Approved: ZHOU Rev No.: V.3 Checked: Wu Lucky Light Electronics Co., Ltd. Date: Mar./18/2006 Drawn: Shu Page: 9 OF 9 http://www.luckylight.cn