RTE02 RTE03 RTE02R RTE02N RTE03N RTE03N/N RTE10 RTE16 RTE10V RTE16V EIA-RS448-2 - Datasheet Archive

 

RTE02 and RTE03 are two types of a subminiature rotary changeover switch to be mounted on PC boards. PC pins are in a 2.54 mm

 

RTE02 RTE02 and RTE03 RTE03 Miniature Rotary Switches RTE02 RTE02 and RTE03 RTE03 are two types of a subminiature rotary changeover switch to be mounted on PC boards. PC pins are in a 2.54 mm (0.100) grid. RTE02 RTE02 with 2 positions RTE03 RTE03 with 3 positions 3 operation versions: ­ screw driver slot without shaft ­ knurled plastic shaft with 4.0 mm ( 0.157) 7.5 mm s(0.295) and screw driver slot ­ button in red, green or black 2 operation directions: ­ from top (in ordering code: N) ­ from the bottom through the PC board (in ordering code: R, e.g. RTE02R RTE02R) Only N version with screw driver slot for automatic insertion Can be wave soldered, resistant to flux soldering Cleaning by immersion in a solvent with or without ultrasonic or by water spray Optionally without or with ground terminal against electrostatical discharge Optionally gold (G) or silver (S) contacts Stop after position 2 of RTE02 RTE02 and after position 3 of RTE03 RTE03 General features Mounted on PC board by pins and ground terminal Terminal size: 0.3 0.5 mm (0.0118 0.0197) Delivered in tubes of 65 pieces for automatic insertion Tin-plated terminals Application The RTE02 RTE02 and RTE03 RTE03 switches are especially designed for telephone bell tune selection, or working mode selection. Their small size also permits all applications on PCB's to save space (computer, instrumentation, security systems etc.). Mechanical data Number of positions Angle between 2 positions Actuating torque Mechanical stop resistance Mechanical life test (indexations) Electrical data Operating Switching voltage Switching current maximum minimum maximum minimum under RTE02 RTE02 2 120° 2 Ncm ± 50% 10 Ncm 1500 Silver 2 pos 50 V DC 2 V DC 100 mA 1 mA Gold 2 pos 30 V DC 20 mV DC 100 mA 10 µA/ 5 V DC 0.3 W Maximum switching power 0.5 W Contact resistance (measured at 50 mV ­ 10 mA) Initial 50 m After endurance 100 m Dielectric strength between contacts 500 V RMS Insulation resistance between 2 contacts (measured at 100 V DC) 104 M (after 21 days RH) 103 M Electrical endurance at max. switching power 1500 indexations Capacitance between contacts 5 pF Environmental data Operating temperature Storage temperature Damp heat resistance Salt mist resistance Industrial environment Vibration, shock Self-extinguishibility Housing RTE03 RTE03 3 2 60° 2 Ncm ± 50% 10 Ncm 1500 Silver 3 pos 50 V DC 2 V DC 100 mA 1 mA 0.5 W Gold 3 pos 30 V DC 20 mV DC 100 mA 10 µA/ 5 V DC 0.3 W 50 m 100 m 500 V RMS 104 M 103 M 1500 indexations 5 pF ­ 25°C to + 85°C ­ 40°C to + 85°C 21 days at 40°C, 93% RH 96 hours H2S, SO2 According to NFC 20700 UL 94 ­ V0 blue in silver (S) version, black in gold (G) version UL 94 ­ HB Actuator Soldering and cleaning recommended process: · Fluxing of the copper side of PCB · Pre-heating at about 85°C · Wave soldering 260°C/2 sec. · Cooling up to ambient temperature · Eventual cleaning by immersion in a solvent, such as trichloro-trifluorethan with or without ultrasonics Please contact us for other processes. Automatic insertions (N version with screw driver slot) RTE can be inserted on following automatic machines: · UNIVERSAL: Unimodule (1 head) or Multimodule (2 heads) Ordering code: see page F-7. Dimensions are shown in mm (inch) Dimensions subject to change www.ittcannon.com F-4 RTE02 RTE02 and RTE03 RTE03 Miniature Rotary Switches Dimensional Drawings RTE02 RTE02 and RTE03 RTE03 Actuation from top side (N) With ground terminal Without ground terminal (0.315) (0.291) (0.291) (0.283) (0.144) RTE02N RTE02N and RTE03N RTE03N Shaft actuation (0.167) (0.167) (0.291) (0.3) (0.291) (0.368) (0.1) (0.1) (7.62 on PCB) (0.3) (0.2) (0.157) (0.167) 7.5 (0.295) RTE02 RTE02 (0.1) (0.1) Shaft color: white RTE03 RTE03 PC Board mounting (seen components side) Normal version = N operation from top side 2 positions with ground terminal (0.01) 2 positions without ground terminal (0.01) (0.1) (0.2) (0.3) (0.0354) 3 positions with ground terminal (0.3) (0.0354) 3 positions without ground terminal (0.1) (0.1) (0.3) (0.0354) (0.1) (0.3) (0.0354) Dimensions are shown in mm (inch) Dimensions subject to change www.ittcannon.com F-5 RTE02 RTE02 and RTE03 RTE03 Miniature Rotary Switches Dimensional Drawings RTE02 RTE02 and RTE03 RTE03 Actuation from bottom side (R) With ground terminal Without ground terminal (10.16 on PCB) (0.451) (0.2) (0.1) (0.1) (0.283) (0.185) (0. 85) 1 (0.309) (0.144) (0.291) Button for the normal versions RTE02N RTE02N and RTE03N/N RTE03N/N, not for R) (0.291) (0.366) (0.945) (0.130) RTE02 RTE02 (0.157) (0.118) (0.0787) (0.283) Available colors: ­ Red ­ Green ­ Black RTE03 RTE03 PC Board layout (seen components side) Reverse version = R operation from bottom side 2 positions with ground terminal (0.1) 2 positions without ground terminal (0.1) (0.2) (0.4) 3,5 Mini. (0.138 min) 3 positions with ground terminal (0.0354) (0.1) 3 positions without ground terminal (0.1) (0.1) (0.1) (0.4) (0.4) (0.4) (0.0354) (0.0354) (0.0354) in PC Board for screw driver operation must be 3.5 mm Dimensions are shown in mm (inch) Dimensions subject to change www.ittcannon.com F-6 RTE02 RTE02 and RTE03 RTE03 Miniature Rotary Switches RTE10 RTE10 and RTE16 RTE16 Miniature Rotary Switches Available versions Without ground terminal 5 SCREW DRIVER SLOT With ground terminal SHAFT 5 Ordering code Example: 1 2 3 4 5 6 7 REVERSE BUTTON 1 RTE 2 10 3 1 4 0 6 2 7 1 1 BTN 2 RTE 3 40 Designation: RTE Types: 02 = 2 positions, 03 = 3 positions, 10 = decimal code, 16 = hexadecimal code Ground terminal: 0 = without, 1 = with, not available for the vertical version (V) Actuation: 0 = screw driver slot, no shaft 1 = shaft 4 mm ( 0.157 inch), 7.5 mm (0.295 inch) long, screwdriver slot 2 = actuator for button, button to be ordered and delivered separately Operating direction: N = normal, from top side R = reverse, from bottom through a PC board or a panel V = vertical, side actuation, only RTE10 RTE10 and RTE16 RTE16 Codes: 0 = none for RTE02 RTE02 and RTE03 RTE03, 1 = binary code for RTE10 RTE10, 2 = binary code complement for RTE10 RTE10, 3 = gray code for RTE10 RTE10, 4 = hexadecimal code for RTE16 RTE16 Contact plating: 1 = silver, only RTE02 RTE02 and RTE03 RTE03 3 = gold, all types Ordering code for RTE buttons; supplied bulk Example: 1 2 3 5 N Button: BTN Designation: RTE Color: 40 = red, 50 = green, 90 = black Dimensions are shown in mm (inch) Dimensions subject to change www.ittcannon.com F-7 RTE10 RTE10 and RTE16 RTE16 Miniature Rotary Switches RTE10 RTE10 and RTE16 RTE16 are two coded types of a subminiature rotary switch to be mounted on PC boards. PC pins are in a 2.54 mm (0.100 inch) grid. RTE10 RTE10 with decimal code, RTE16 RTE16 with hexadecimal code. 3 operation versions: ­ screw driver slot without shaft ­ knurled plastic shaft with 4.0 mm ( 0.157) 7.5 mm (0.295) and screw driver slot ­ button in red, green or black Only version with screw driver slot for automatic insertion Can be wave soldered, resistant to flux soldering Cleaning by immersion in a solvent with or without ultrasonic or by water spray Optionally without or with ground terminal against electrostatic discharge Gold contacts, tin plated Applications RTE10 RTE10 is specially designed for direct binary coding with 10 positions and RTE16 RTE16 for hexadecimal coding with 16 positions RTE10 RTE10 versions with binary code complement or Gray code are also available Its small size makes it particularly suitable for all applications on PC boards where it is necessary to save space (computers, instruments, telecom, security, etc) Characteristics Dimensions of terminals: 0.3 0.5 mm (0.0118 0.0197) Positioning by metallic indexing Marked on top face Packing for delivery: tubes of 65 pieces for automatic insertion Automatic insertion RTE with screw driver slot can be inserted on following automatic machines: UNIVERSAL: Unimod (1 head), or Multimode (2 heads) Mechanical data Number of positions Angle between 2 positions Actuating torque Mechanical stop resistance Mechanical life test (indexations) Electrical data Operating Switching voltage Switching current maximum minimum maximum minimum RTE10 RTE10 10 36° 1.5 Ncm ± 50% without 20 000 RTE16 RTE16 16 22.5° 1.5 Ncm ± 50% without 20 000 10 pos 30 V DC 20 mV DC 100 mA 10 µA/5 V DC 0.3 W 16 pos 30 V DC 20 mV DC 100 mA 10 µA/5 V DC 0.3 W Maximum switching power Contact resistance (measured at 50 mV ­ 10 mA) Initial 100 m After endurance 150 m Dielectric strength between contacts 300 V rms Insulation resistance between 2 contacts (measured at 100 V DC) 1010 (after 21 days RH) 109 Electrical endurance at max. switching power 20 000 indexations Capacitance between contacts 5 pF Environmental data Operating temperature Storage temperature Damp heat resistance Salt mist resistance Industrial environment Vibrations, shocks Self-extinguishibility Housing (blue) Actuator 100 m 150 m 300 V rms 1010 109 20 000 indexations 5 pF ­ 25°C to + 85°C ­ 40°C to + 85°C 21 days at 40°C, 93% RH 96 hours at 35°C H2S, SO2 According to NFC 20700 UL 94 ­ VO UL 94 ­ HB Soldering and cleaning Resinous flux: · Fluxing of PCB under side · Pre-heating 85°C · Wave soldering 260°C/2 sec. · Cooling up to ambient temperature · Immersion cleaning in solvent (trichlo-trifluorethan with or without ultrasound) · Consult with us for other soldering and cleaning processes Please contact us for other processes. Available versions (without or with ground terminal) RTE10 RTE10 and RTE16 RTE16 screw driver slot version for automatic insertion Ordering code: see page F-7. RTE10 RTE10 and RTE16 RTE16 Shaft version RTE10 RTE10 and RTE16 RTE16 Button version Dimensions are shown in mm (inch) Dimensions subject to change Dimensions are shown in mm (inch) Dimensions subject to change www.ittcannon.com F-8 RTE10 RTE10 and RTE16 RTE16 Miniature Rotary Switches Dimensional Drawings PC Board layout (seen components side) RTE10 RTE10 or RTE16 RTE16 with ground terminal RTE10 RTE10 and RTE16 RTE16 screw driver slot version (0.1) Without ground terminal (0.3) With ground terminal (0.1) (0.315) ( 0.0354) (0.291) (0.283) RTE10 RTE10 or RTE16 RTE16 without ground terminal (0.291) (0.1) (0.1) (0.3) (0.167) (0.167) (0.144) (0.291) (0.1) (0.368) (0.1) (7.62 on PCB) (0.3) ( 0.0354) RTE10 RTE10 ­ Button version RTE16 RTE16 RTE10 RTE10 ­ Shaft version 7.2 (0.283) 9.35 (0.368) RTE10 RTE10 8 (0.318) (0.1) (0.1) 7.2 (0.283) 9.35 (0.368) (0.291) Note: For shaft and button details see RTE02 RTE02 or RTE03 RTE03 (0.144) (0.295) Truth table RTE16 RTE16 Hexadecimal Code 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 C X X X X X X X X X X X X X X X X RTE10 RTE10 Direct Binary Code 1 2 4 8 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 0 1 2 3 4 5 6 7 8 9 C X X X X X X X X X X RTE10 RTE10 Complement Binary Code 1 2 4 8 0 1 2 3 4 5 6 7 8 9 X X X X X X X X X X X X X X X C X X X X X X X X X X 1 2 4 X X X X X X X X X X X X X X X X X RTE10 RTE10 Gray Code 8 X X X X X X X X 1 2 3 4 5 6 7 8 9 10 C X X X X X X X X X X 1 2 3 4 X X X X X X X X X X X X X X X X X Note: the advantage of the Gray Code is that you change only one digit at the time. Dimensions are shown in mm (inch) Dimensions subject to change www.ittcannon.com F-9 RTEV Miniature Rotary Switch with Vertical Operation To complete the RTE product range family, a vertical version is now available. The main advantage of this RTE vertical is the P.C.B. mounting providing a direct actuation from a front panel. Main features 4.5 mm from the P.C.B. to shaft axis Available with button, screw driver or knob shaft 2 types: RTE10V RTE10V and RTE16V RTE16V Manual insertion Bulk packed of 250 pieces Same electrical and mechanical characteristics as standard versions of RTE10 RTE10 and RTE16 RTE16 No ground terminal available. Truth table RTE16 RTE16 Hexadecimal Code 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 C X X X X X X X X X X X X X X X X 1 2 4 8 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X RTE10 RTE10 Complement Binary Code 0 1 2 3 4 5 6 7 8 9 C X X X X X X X X X X 1 X 2 X X X X 4 X X X X X X X X X X X X RTE10 RTE10 Direct Binary Code 8 X X X X X X X X 0 1 2 3 4 5 6 7 8 9 C X X X X X X X X X X 1 2 4 8 X X X X X X X X X X X X X X X RTE10 RTE10 Gray Code 1 2 3 4 5 6 7 8 9 10 C X X X X X X X X X X 1 X X X X X 2 X X X X 3 X X X X X X Mechanical data Number of positions Angle between 2 positions Actuating torque Mechanical stop resistance Mechanical life test (indexations) Electrical data Operating Switching voltage Switching current maximum minimum maximum minimum Environmental data Operating temperature Storage temperature Damp heat resistance Salt mist resistance Industrial environment Vibrations, shocks Self-extinguishibility Housing (blue) Actuator Soldering and cleaning/Resinous flux: · Fluxing of PCB under side · Pre-heating 85°C · Wave soldering 260°C/2 sec. · Cooling up to ambient temperature Please contact us for other processes. 1 2 3 4 X X Note: the advantage of the Gray Code is that you change only one digit at the time. RTE16V RTE16V 16 22.5° 1.5 Ncm ± 50% without 20 000 10 positions 30 V DC 20 mV DC 100 mA 10 µA/5 V DC 0.3 W 16 positions 30 V DC 20 mV DC 100 mA 10 µA/5 V DC 0.3 W Maximum switching power Contact resistance (measured at 50 mV ­ 10 mA) Initial 100 m After endurance 150 m Dielectric strength between contacts 300 V rms Insulation resistance between 2 contacts (measured at 100 V DC) 1010 (after 21 days RH) 109 Electrical endurance at max. switching power 20 000 indexations Capacitance between contacts 5 pF Ordering code 4 RTE10V RTE10V 10 36° 1.5 Ncm ± 50% without 20 000 5 6 7 100 m 150 m 300 V rms 1010 109 20 000 indexations 5 pF ­ 25°C to + 85°C ­ 40°C to + 85°C 21 days at 40°C, 93% RH 96 hours at 35°C H2S, SO2 According to NFC 20700 UL 94 ­ VO UL 94 ­ HB · Immersion cleaning in solvent (trichlo-trifluorethan with or without ultrasound) · Consult with us for other soldering and cleaning processes 1 2 Example: RTE 10 3 0 4 1 5 V 6 1 7 3 Designation: RTE Types: 10 (decimal code), 16 (hexadecimal code) Ground terminal: 0 (without) Actuation: 0 (screw driver slot), 1 (shaft 4 mm ( 0.157 inch) long, screwdriver slot), 2 (actuator for button, button to be ordered and delivered separately) Operating direction: V (vertical, side actuation) Codes: 1 (binary code for RTE10 RTE10), 2 (binary code complement for RTE10 RTE10), 3 (grey code for RTE10 RTE10), 4 (hexadecimal code for RTE16 RTE16) Contact material: 3 (RTE10 RTE10 and RTE16 RTE16 only available with gold contacts) Dimensions are shown in mm (inch) Dimensions subject to change www.ittcannon.com F-10 RTEV Miniature Rotary Switch with Vertical Operation Dimensional Drawings (0.335) RTE-V with screw driver slot (0.157) (0.287) (0.315) (0.177) (0.144) (0.144) (0.114) (0.2) (0.1) (0.1) (0.2) (0.291) PCB layout Component side (0.0354) RTE-V with long shaft 4 mm (0.157 inch) and screw driver slot (0.335) (0.295) (0.157) (.287) (0.287) (0.315) (0.177) (0.144) (0.144) (0.114) (0.2) (0.2) (0.157) (0.291) (0.1) (0.1) PCB layout Component side (0.0354) RTE-V with actuator for button (button to be ordered separately) (0.335) (0.154) (0.157) (0.287) (0.315) (0.114) (0.2) (0.1) (0.1) (0.2) (0.291) (0.177) (0.144) (0.144) PCB layout Component side (0.0354) Dimensions are shown in mm (inch) Dimensions subject to change www.ittcannon.com F-11 RTE Miniature Rotary Switch for SMT The subminiature Rotary switches RTE 02, 03, 10 and 16 positions are available with G type terminals, to facilitate surface mounting on PCB's. The tape and reel packaging allows an automatic mounting process with standard pick and place machines. Its small size makes the RTE family particularily suitable for all coding applications on PC Boards where it is necessary to save space. Main features Same mechanical and electrical data as the thru hole version Two different types of actuators available: screw driver slot and axis for button Hexadecimal code: RTE 16 Binary or Gray code: RTE 10 Change-over: RTE 02 and RTE 03 Totally washable and sealed Suitable for infra-red reflow soldering processes Gold contacts RTE 10, 16 Gold or Silver contacts RTE 02, 03 Tin plated terminals Main Applications Timers Alarm systems Domestic applications Automotive Industrial processes Instrumentation Security Systems Mechanical data See the detailed catalog pages starting on F-4 for RTE02 RTE02, RTE03 RTE03, RTE10 RTE10 and RTE16 RTE16 Electrical data See the detailed catalog pages starting on F-4 for RTE02 RTE02, RTE03 RTE03, RTE10 RTE10 and RTE16 RTE16 Environmental data See the detailed catalog pages starting on F-4 for RTE02 RTE02, RTE03 RTE03, RTE10 RTE10 and RTE16 RTE16 Soldering Conditions Infra red reflow soldering Pre-heating: Heating Manual soldering: Cleaning: According to CECC 00 802 Temperature 130°C 60S Temperature 215°C with a peak of 260°C during 10S Temperature 260°C 5S Washable according to EIA-RS448-2 EIA-RS448-2 test and IP-67 IP-67 Packaging RTE are delivered on continuous tape in reel: width 16 mm and external diameter 330 mm Actuator for screw driver 1250 pieces per reel Actuator for button 750 pieces per reel Ordering code 1 2 3 4 5 6 7 1 2 Example: RTE 10 3 0 4 0 5 G 6 2 7 3 Designation: RTE Types: 02 = 2 positions 03 = 3 positions 10 = decimal code 16 = hexadecimal code Ground terminal: 0 (without) Actuation: 0 = screw driver slot, no shaft 2 = actuator for button, button to be ordered & delivered separately Operating direction: G = surface mount "G wing" type Codes: 0 = none for RTE02 RTE02 & RTE03 RTE03 1 = binary code for RTE10 RTE10 2 = binary code complement for RTE10 RTE10 3 = gray code for RTE10 RTE10 4 = hexadecimal code for RTE16 RTE16 Contact material: 1 = silver, only RTE02 RTE02 & RTE03 RTE03 3 = gold, all types Dimensions are shown in mm (inch) Dimensions subject to change www.ittcannon.com F-12 RTE Miniature Rotary Switches for SMT Dimensional Drawings RTE 02 00 G 03 RTE 03 00 G 03 RTE 10 00 G 33 RTE 16 00 G 43 RTE 10 02 G 13 Screwdriver slot version RTE 16 02 G 43 Actuator version (0.283) (0.291) (0.100) (0.100) (0.100) (0.154) (0.148) (0.100) (0.004) (0.027 x 5) (0.033 x5) (0.167) (0.004) (0.020) (0.148) (0.291) (0.148) (0.291) (0.024 x 5) (0.031 x 5) (0.197) (0.291) (0.291) (0.197) PC Board Mounting (seen components side) RTE 02 RTE 03 / 10 /16 (0.100) (0.100) (0.110) (0.100) (0.106 x4) (0.106 x4) (0.110) (0.110) (0.110) (0.100) (0.063 x 4) (0.063 x 4) Dimensions are shown in mm (inch) Dimensions subject to change www.ittcannon.com F-13