PC-29-0209 PC-29 - Datasheet Archive

 

SPECIFICATION Specification No : PC-29-0209 Part No. : PC-29 Product Name : TheStripeTM 850/900/1800/1900MHz GSM PCB Antenna

 

the antenna solutions provider SPECIFICATION Specification No : PC-29-0209 PC-29-0209 Part No. : PC-29 PC-29 Product Name : TheStripeTM 850/900/1800/1900MHz GSM PCB Antenna Features : 66mm*25mm*0.8mm 144mm Length 0.81mm Diameter Cable Ipex MHFII Photo : REVISION STATUS Version Date 01 Nov 17 2006 1.0 System th Page Revision Description Prepared Approved All New format TW Product Centre Ronan Quinlan the antenna solutions provider This miniaturized low profile PCB antenna is based on smart TheStripeTM antenna technology. It consists of a PCB antenna and mini coaxial cable. 2.0 General 2.1 Environmental Conditions 2.1.1 Operation Temperature -20°C to + 65°C 2.1.2 Storage Temperature -30°C to + 75°C 2.1.3 Relative Humidity 40% to 95% 2.2 Cable & Connector RF Coaxial Cable 0.81 ± 0.1mm 2.3.1 RF Cable L = 144 +/- 3 mm White 2.3.2 RF Connector Ipex MHF II (Hirose U.FL compatible) 3.0 Antenna 3.1 Communication System 3.2 Frequency Band 3.3 VSWR 3.4 Return Loss 3.5 Impedance 3.6 Radiation Pattern 3.7 Polarization AMPS GSM DCS PCS 850 MHz 900 MHz 1800 MHz 1900 MHz 1.92 1.65 1.92 1.40 -10 dB -12.24 dB - 10.01 dB 50 Ohm Omnidirectional Horizontal -15.55 dB the antenna solutions provider 4.0 Mechanical Dimensions Z Note : 1. The upper face of the PCB is in the X axis Y X 2. Connector positioning is towards the Z direction the antenna solutions provider 5.0 Antenna Electrical Characteristics 5.1 VSWR the antenna solutions provider 5.2 Return Loss the antenna solutions provider 6.0 Environmental Characteristics Test Items Procedure Requirement Starting at -40 for 30minutes and then cycled to +85 to 1. remain 30minutes Thermal Shock The value of return loss must be within product specifications (a complete cycle). after this test. To repeat 5 complete cycles. 2. be evident. (Refer to IEC 68-2-14 Method Na) 1. Storage Temperature (Cold) No physical deformation should The value of return loss must be Samples must be put into -30°C chamber for 72 hours within product specifications and samples shall be powered during test. after this test. (Refer to IEC 68-2-1 Method Aa) 2. No physical deformation should be evident. 1. The value of return loss must Storage Temperature (Dry Heat) Samples must be put into +75°C chamber for 72 hours be within product and samples shall be powered during test. specifications after this test. (Refer to IEC 68-2-1 Method Ba) 2. No physical deformation should be evident. Operating Temperature (Cold) Samples must be put into -20°C chamber for 2 hours and samples shall be powered during test. (Refer to IEC 1. The value of return loss must met specification during test/after test 68-2-1 Method Aa) 2. no mechanical defects after test. Operating Samples must be put into +65°C chamber for 72 hours 1. The value of return loss must met Temperature and samples shall be powered during test. (Refer to IEC specification during test/after test (Dry Heat) 68-2-1 Method Ba) 2. no mechanical defects after test. the antenna solutions provider 7.0 Antenna Test Setup 7.1 Equipment Radiation Pattern Testing - Anechoic Chamber HORN Standard Antenna DUT Antenna 500 cm 8720 C Network Analyzer Rotator Controller the antenna solutions provider HORIZONTAL MOUNTING 850 MHz PC-29-0209 PC-29-0209 HORIZONTAL MOUNTING 900 MHz the antenna solutions provider HORIZONTAL MOUNTING 1800 MHz HORIZONTAL MOUNTING 1900 MHz the antenna solutions provider VERTICAL MOUNTING 850 MHz VERTICAL MOUNTING 900 MHz the antenna solutions provider VERTICAL MOUNTING 1800MHz VERTICAL MOUNTING 1900 MHz the antenna solutions provider 8.0 Antenna Packaging