P1020/P1011 P1020RDB P1020 P1011 P2020 RS-232 P1020RDBFS - Datasheet Archive
P1020/P1011 Reference Design Board The P1020RDB is a highly integrated The P1020RDB platform features reference design board that
QorIQ Multicore Processor Development P1020/P1011 P1020/P1011 Reference Design Board The P1020RDB P1020RDB is a highly integrated The P1020RDB P1020RDB platform features reference design board that can help shorten 512 MB unbuffered DDR2 SDRAM, your time to market. The reference design 16 MB NOR flash and 32 MB NAND is aimed at networking, wired and wireless flash, where the platforms can boot access, industrial and medical applications. from either NOR or NAND flash This cost-effective board is based on the memory. It supports six Gigabit- QorIQ P1020 P1020 processor family, along with capable ports via an SGMII PHY, leading-edge external components to help an RGMII PHY and an on-board you quickly design and implement your switch with four ports, as well as target application. two ports of USB on-the-go (OTG), The P1020RDB P1020RDB leverages the P1020 P1020 processor and supports both the dual-core P1020 P1020 and single-core P1011 P1011 configurations. The P1020 P1020 processor family is based on the e500 core, built on Power Architecture® technology, which has a core frequency range of 533800 MHz, and supports a 32 KB instruction and L1 data cache and a shared 256 KB frontside cache. The P1020 P1020 also supports three Gigabit Ethernet controllers with IEEE® 1588 v2 support, USB 2.0, up to two PCI Express® 1.0a controllers, up to two SGMII SerDes interfaces, 32-bit DDR2/3 with ECC, SPI controller supporting booting from SPI serial flash memory, SD/MMC card controller supporting booting from flash cards and an integrated security engine. The new P1020 P1020 family, built in 45 nm process four FXS ports and one FXO port via relay. The P1020RDB P1020RDB also supports a PCI Express add-in connector and a MiniPCI Express slot, as well as an SD/MMC card slot. These components, integrated with the P1020 P1020 family, provide an application-specific platform that can help you get a jump start on your next application design. In addition, the P1020RDB P1020RDB provides a simplified migration path for existing PowerQUICC processor customers wishing to migrate to QorIQ multicore processors. Customers can migrate to the single-core P1011 P1011 initially, as a stepping stone, on their way to dual multicore processing. technology, provides high integration that Since the P1020 P1020 family is pin-compatible with simplifies board design and offers a cost- the P2020 P2020 family, the P1020RDB P1020RDB can also effective solution. be used as a development vehicle for the P2020 P2020 family. Along with the hardware support, the P1020RDB P1020RDB comes with a board support package (BSP) that includes both U-boot and Linux® 2.6 operating system support. The platform is also available with third-party software applications. To see demonstrations or to acquire details of Freescale's third-party applications for this platform, please contact your local Freescale sales office. P1020RDB P1020RDB Block Diagram Clocking Security Acceleration (optional) XOR Mini USB Mini USB Power POR Configuration e500 Core 2x USB 2.0 Reset PLD DDR2/DDR3 SDRAM Controller e500 Core 256 KB L2 Cache 32 KB 32 KB L1 I-Cache L1 D-Cache 8-bit MCU 32 KB 32 KB L1 I-Cache L1 D-Cache x32 Enhanced Local Bus Controller (eLBC) Coherency Module DDR2 Discrete NAND Flash NOR Flash System Bus DB9 RS-232 RS-232 Serial RJ45 RGMII PHY DUART RGMII RGMII RJ45 RJ45 eTSEC SPI PCI Express® eTSEC RJ45 PCI Express 4-ch. DMA 4-lane SerDes 5-port Switch RJ45 eSDHC On-Chip Network 3 x Gigabit Ethernet EEPROM SD/MMC JTAG/COP I2C Real-Time EEPROM Clock IEEE® 1588 HDR Not Connected RJ11 TDM SGMII PHY RJ45 DAC VCXO Dual SLIC PCI Express RJ11 RJ11 RJ11 RJ11 MiniPCI Express PCI Express P1020RDB P1020RDB Board Features IEEE 1588 v2 Mini-ITX Form Factor Memory · Clock input from DAC/VCXO circuitry · 170 mm x 170 mm · 512 MB DDR2 · Accessible via test header · 6-layer PCB routing (4-layer signals, · 16 MB (128 MB device) NOR flash memory · 32 MB NAND flash memory · 16 MB SPI ROM PCI Express Interconnects · One standard PCI Express connector (x1) · One mini PCI Express connector (x1) 2-layer power and ground) System Integration Lead-Free (ROHS), CE and FCC Certification · Dual I2C · SD/MMC card slot · Dual USB Software Tools Mini AB connectors on I/O panel (default) · UARTs · Cross compile and native GNU tool chain One DB9 connector Ethernet Six 10/100/1000 ports as follows: · Linux 2.6.x Kernel · CodeWarrior USB TAP · Dual SLIC for FXS/FXO interfaces · Four ports from L2 switch connected to eTSEC1 · One SGMII PHY connected to eTSEC2 · One RGMII PHY connected to eTSEC3 Learn More: Freescale, the Freescale logo, CodeWarrior, PowerQUICC and QorIQ are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product or service names are the property of their respective owners. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. © Freescale Semiconductor, Inc. 2010. Document Number: P1020RDBFS P1020RDBFS REV 0 For current information about Freescale products and documentation, please visit www.freescale.com/QorIQ.