P0430WQLC-T HX5116 480RGB CA210 CCIR601 CCIR656

Document No.: Tentative Product Specification Module name: P0430WQLC-T Issue date: 2007/12/26 Version: 1.0 Customer Approved by

P0430WQLC-T P0430WQLC-T Document No.: Tentative Product Specification Module name: P0430WQLC-T P0430WQLC-T Issue date: 2007/12/26 Version: 1.0 Customer Approved by Customer Approved by CMEL PD Division ENG Division QA Dept Note: 1. The information contained herein may be change without prior notice. It is therefore advisable to contact CHI MEI EL Corp. before designed your product based on this specification. 1 P0430WQLC-T P0430WQLC-T Document No.: Reversion History Version Date Page Ver.1.0 2007/12/26 All Description Tentative specification was first issued 2 P0430WQLC-T P0430WQLC-T Document No.: 1. Purpose: This documentation defines general product specification for OLED module supplied by CMEL. The information described in this technical specification is tentative. Please Contact CMEL's representative while your product is modified. 2. General Description: Driving Mode: Active Matrix Color Mode: Full Color (16M color) Driver IC: HX5116 HX5116, COG Assembly Interface: 8bit serial RGB and 24bit parallel RGB interface Application: Portable DVD, PMP, GPS, Photo Frame etc. 3. Mechanical Data: No. Items Specification Unit 1 Diagonal Size 4.3 Inch 2 Resolution 480 RGB x 272 3 Pixel Pitch H: 0.198 4 Active Area 95.0 x 53.8 mm 5 Outline Area 103.5 x 67 mm 6 Thickness 1.95 mm 7 Weight TBD g V: 0.198 3 um P0430WQLC-T P0430WQLC-T Document No.: 4. Maximum ratings: Symbol Parameter Value Unit VCC Logic Supply Voltage -0.3 to +3.6 V VCI Analog Supply Voltage -0.3 to +3.6 V TA Operating Temperature -20 to +60 Storage Temperature -40 to +85 Tstg Table 7.1 Maximum ratings Maximum ratings are those values beyond which damages to the device may occur. Functional operation should be restricted to the limits in the Electrical Characteristics tables or Pin Description section. Unused outputs must be left open. 4 P0430WQLC-T P0430WQLC-T Document No.: 5. Electrical Characteristic: 5.1 DC Characteristic DC Characteristics (Unless otherwise specified, Voltage Referenced to VSS = 0V, VCC = 1.5 to 3.6V, TA = -20 to 70C) Parameter Symbol Test condition Min. Typ. Max. Unit VCC - 1.5 - 3.6 V VCI - 3.0 - 3.6 V DDVDH Output Voltage 1 DDVDH Set CP1X=0 4.9 5.1 5.3 V DDVDH Output Voltage 2 DDVDH Set CP1X=1 5.8 6.0 6.2 V VGAM1OUT Output Voltage 1 VGAM1OUT Set CP1X=0 4.7 4.8 4.9 V VGAM1OUT Output Voltage 2 VGAM1OUT Set CP1X=1 5.7 5.8 5.9 V Gate driver High Output Voltage VGH - +3 - +8 V Gate driver Low Output Voltage VGL - -8 - -3 V OLED Diode Refer Voltage ARREF - -8 - +8 V Logic High Output Voltage VOH Iout=-400µA 0.8 * VCC - VCC V Logic Low Output Voltage VOL Iout=400µA 0 - 0.2 * VCC V Logic High Input voltage VIH 0.8 * VCC - VCC V Logic Low Input voltage VIL 0 - 0.2 * VCC V System power supply pins of the logic block Booster Reference Supply Voltage Range - Logic Input Current IIL/IIH No pull up or pull low -1 - 1 µA Pull high resistance RH Pull up pins 600 900 1200 K Pull low resistance RL Pull low pins 600 900 1200 K High Output Current IOH 50 - - µA Low Output Current IOL - - -50 µA Output leakage Current IOZ -1 - 1 µA Output voltage offset VOS Output voltage deviation VOD Analog standby current ISTB Analog operating current IVCI Analog operating current IVCI Logic Pins Input Capacitance CIN S1~S107, Vo=4.9V vs. 4V S1~S107, Vo=0.1V vs. 1V S1~S107, ±10 S1~S107, Vo=0.1V~DDVDH-0.1V VCI=3.0V, VCI=3.0V, 10 uA TBD VCI=3.0V, S1~S160 no load - mV TBD S1~S160 no load 5 mV - Stand by mode - mV ±10 Vo=0.1V~DDVDH-0.1V mV 5 7.5 pF P0430WQLC-T P0430WQLC-T Document No.: 5.2 AC Characteristic 5.2.1 AC Electrical Characteristics 6 P0430WQLC-T P0430WQLC-T Document No.: Clock and Data input waveforms Define the HSYNC to VSYNC timing for RGB mode 7 P0430WQLC-T P0430WQLC-T Document No.: 5.2.2 480RGB 480RGB X 272 serial RGB interface 5.2.2 480RGB 480RGB X 272 parallel RGB interface 8 P0430WQLC-T P0430WQLC-T Document No.: Serial RGB Horizontal Data Format Parallel RGB Horizontal Data Format Digital RGB Vertical Data Format 9 P0430WQLC-T P0430WQLC-T Document No.: 6. Electro-Optical Characteristic: Items Symbol Operating Luminance L Power Consumption Wx CIEy (White) Wy Viewing Angle VA Contrast Max Unit Remark 2 Tres CIEx (White) Typ. Pon Response Time Min Cd/m (1)(5) 800 mW 30% pixels on (1) 50 uS (2) 0.31 - (5) 0.33 - (5) 160 170 Degree (3) CR 5000:1 10000:1 LTop Operation Lifetime 250 20000 Hrs Note: Measuring surrounding: dark room Surrounding temperature: 25oC 1. Test condition: a. AR_VDD= 5V, AR_VSS= -5V b. IC Initial Register Setting: TBD 2. Response Time test condition Tr Tf 100% 90% 10% Time 10 (4) (1)(6) P0430WQLC-T P0430WQLC-T Document No.: 3. Viewing angle test condition: Vss(GND) =270° 4. Contrast Luminance with all pixels white CR = Luminance with all pixels black 5. Optical tester: CA210 CA210 6. Brightness of 30% power consumption. Operating Life Time is defined when the luminance has decayed to less than 50% of the initial measured luminance before life test. 11 P0430WQLC-T P0430WQLC-T Document No.: 7. System Diagram: TBD 12 P0430WQLC-T P0430WQLC-T Document No.: 8. Pin Assignment: PIN Symbol I/O Description 1 TP1 I Touch panel P1 2 TP2 I Touch panel P2 3 TP3 I Touch panel P3. 4 TP4 I Touch panel P4 5 AR_VSS I Negative voltage for OLED 6 AR_VSS I Negative voltage for OLED 7 AR_VSS I Negative voltage for OLED 8 AR_VDD I Positive voltage for OLED 9 AR_VDD I Positive voltage for OLED 10 AR_VDD I Remarks Positive voltage for OLED 11 ARREF I/O 12 VGL I/O 13 VGH I/O Panel refers voltage of the regulator ARREF or external input voltage. (-8V~+8V) Low Voltage output of regulator VGL or external input voltage. (-3V~-8V) High Voltage output of regulator VGH or external input voltage. (+3V~+8V) 14 LVO I/O Negative output voltage of the booster2. (-8.5V) I/O Connect to the step-up circuit, capacitors according to the step-up factor. Leave this pin open if the internal step-up circuit is not used. I/O Positive output voltage of the booster2. (8.5V) I/O Connect to the step-up circuit, capacitors according to the step-up factor. Leave this pin open if the internal step-up circuit is not used. I/O Connect to the step-up circuit, 4capacitors according to the step-up factor. Leave this pin open if the internal step-up circuit is not used. 15 C22N 16 C22P 17 HVO 18 C21P 19 C21N 20 C11N 21 C11P 22 C12N 23 C12P 24 PVSS 25 DDVDH P I/O Charge pump ground pin, it must connect to external ground. Output voltage of the booster1. (5.1V/6.0V) 26 VSSA P Analog ground pin. It must connect to external ground. 27 VSSA P Analog ground pin. It must connect to external ground. 28 VCI P A power supply for the Analog circuit. (2.7V~3.6V) 29 VCI P A power supply for the Analog circuit. (2.7V~3.6V) 30 VGAM1OUT I/O Output voltage of the VGAM1OUT regulator and used positive power of source driver. (4.8V/5.8V) Internal logic voltage input or output pin I/O 31 VDDD VDC_ENB=0, VDDD is output, please connect to 1uF capacitor. VDC0 VDDD Status 0 1.8V Normal display 13 P0430WQLC-T P0430WQLC-T Document No.: 1 2.5V OTP program VDC_ENB=1, VDDD is input. (Input range = 1.6V~2.75V) 32 VCC P A power supply for the Digital circuit. (1.5V~3.6V) 33 VSSD P Digital ground pin. It must connect to external ground. 34 NRESET I Reset pin. Setting either pin low initializes the LSI. Must be reset after power is supplied. (Normally pull high) 35 NCS I Serial Interface chip enable pin. (Normally pull high) 36 SCL I Serial Interface clock input pin. (Normally pull high) 37 SDA I Serial Interface data line. (Normally pull high) 38 DE I Negative voltage for OLED Frame synchronizing signal. I 39 VSYNC If VSPL=0: Active low. If VSPL=1: Active high. Line synchronizing signal. I 40 HSYNC If HSPL=0: Active low. If HSPL=1: Active high. Dot clock signal. I 41 DCLK 42 D27 43 D26 44 D25 If DPL=0: Data are input on the rising edge of DOTCLK. If DPL=1: Data are input on the falling edge of DOTCLK. I Digital data input. DX0 is LSB and DX7 is MSB. (Normally pull low) 1. If parallel RGB input mode is used, D0X, D1X, and D2X indicate R, G, and B data in turn. 45 D24 2. If serial RGB or RGBD or CCIR601 CCIR601 or CCIR656 CCIR656 input mode is 46 D23 selected, only D07~D00 are used, and others short to GND. 47 D22 DX7~DX0 has 8-bit width, respectively to compose 16,777,216 color and 256 gray scale of 1 pixel. 48 D21 49 D20 50 D17 51 D16 52 D15 53 D14 54 D13 55 D12 56 D11 57 D10 58 D07 59 D06 60 D05 61 D04 14 P0430WQLC-T P0430WQLC-T Document No.: 62 D03 63 D02 64 D01 65 D00 66 AR_VDD I Positive voltage for OLED 67 AR_VDD I Positive voltage for OLED 68 AR_VDD I Positive voltage for OLED 69 AR_VSS I Negative voltage for OLED 70 AR_VSS I Negative voltage for OLED 71 AR_VSS I Negative voltage for OLED 15 P0430WQLC-T P0430WQLC-T Document No.: 9. External Dimension: 16 P0430WQLC-T P0430WQLC-T Document No.: 10. Reliability Test: TBD 17 P0430WQLC-T P0430WQLC-T Document No.: 11. Package: TBD 18