NL10276BC16-01 DOD-PP-0232 DOD-MD-0019 UL60950-1/CSA E170632 2002/95/EC K5400 - Datasheet Archive

 

NL10276BC16-01 21cm (8.4 Type) XGA LVDS interface (1port) DATA SHEET DOD-PP-0232 (5th edition) This DATA SHEET is updated

 

TFT COLOR LCD MODULE NL10276BC16-01 NL10276BC16-01 21cm (8.4 Type) XGA LVDS interface (1port) DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) This DATA SHEET is updated document from DOD-MD-0019 DOD-MD-0019(4). All information is subject to change without notice. Please confirm the sales representative before starting to design your system. Document Number: DOD-PP-0232 DOD-PP-0232 (5th edition) Published date: May 2007 CP(N) 1 © NEC LCD Technologies, Ltd. 2003-2007 All rights reserved. NL10276BC16-01 NL10276BC16-01 INTRODUCTION The Copyright to this document belongs to NEC LCD Technologies, Ltd. (hereinafter called "NEC"). No part of this document will be used, reproduced or copied without prior written consent of NEC. NEC does and will not assume any liability for infringement of patents, copyrights or other intellectual property rights of any third party arising out of or in connection with application of the products described herein except for that directly attributable to mechanisms and workmanship thereof. No license, express or implied, is granted under any patent, copyright or other intellectual property right of NEC. Some electronic parts/components would fail or malfunction at a certain rate. In spite of every effort to enhance reliability of products by NEC, the possibility of failures and malfunction might not be avoided entirely. To prevent the risks of damage to death, human bodily injury or other property arising out thereof or in connection therewith, each customer is required to take sufficient measures in its safety designs and plans including, but not limited to, redundant system, fire-containment and anti-failure. The products are classified into three quality grades: "Standard", "Special", and "Specific" of the highest grade of a quality assurance program at the choice of a customer. Each quality grade is designed for applications described below. Any customer who intends to use a product for application other than that of Standard quality grade is required to contact an NEC sales representative in advance. The Standard quality grade applies to the products developed, designed and manufactured in accordance with the NEC standard quality assurance program, which are designed for such application as any failure or malfunction of the products (sets) or parts/components incorporated therein a customer uses are, directly or indirectly, free of any damage to death, human bodily injury or other property, like general electronic devices. Examples: Computers, office automation equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment, industrial robots, etc. The Special quality grade applies to the products developed, designed and manufactured in accordance with an NEC quality assurance program stricter than the standard one, which are designed for such application as any failure or malfunction of the products (sets) or parts/components incorporated therein a customer uses might directly cause any damage to death, human bodily injury or other property, or such application under more severe condition than that defined in the Standard quality grade without such direct damage. Examples: Control systems for transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, medical equipment not specifically designed for life support, safety equipment, etc. The Specific quality grade applies to the products developed, designed and manufactured in accordance with the standards or quality assurance program designated by a customer who requires an extremely higher level of reliability and quality for such products. Examples: Military systems, aircraft control equipment, aerospace equipment, nuclear reactor control systems, medical equipment/devices/systems for life support, etc. The quality grade of this product is the "Standard" unless otherwise specified in this document. DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 2 NL10276BC16-01 NL10276BC16-01 CONTENTS INTRODUCTION . 2 1. OUTLINE. 4 1.1 STRUCTURE AND PRINCIPLE. 4 1.2 APPLICATION. 4 1.3 FEATURES. 4 2. GENERAL SPECIFICATIONS . 5 3. BLOCK DIAGRAM . 6 4. DETAILED SPECIFICATIONS . 7 4.1 MECHANICAL SPECIFICATIONS. 7 4.2 ABSOLUTE MAXIMUM RATINGS . 7 4.3 ELECTRICAL CHARACTERISTICS. 8 4.3.1 LCD panel signal processing board . 8 4.3.2 Backlight lamp . 9 4.3.3 Power supply voltage ripple. 10 4.3.4 Fuse. 10 4.4 POWER SUPPLY VOLTAGE SEQUENCE . 11 4.4.1 LCD panel signal processing board . 11 4.4.2 Inverter. 11 4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS. 12 4.5.1 LCD panel signal processing board . 12 4.5.2 Backlight lamp . 13 4.5.3 Positions of plug and socket . 13 4.5.4 Connection between receiver and transmitter for LVDS . 14 4.6 DISPLAY COLORS AND INPUT DATA SIGNALS . 16 4.6.1 Combinations between input data signals and FRC signal . 16 4.6.2 16,777,216 colors. 17 4.6.3 262,144 colors. 18 4.7 DISPLAY POSITIONS. 19 4.8 SCANNING DIRECTIONS . 19 4.9 INPUT SIGNAL TIMINGS. 20 4.9.1 Outline of input signal timings . 20 4.9.2 Timing characteristics . 21 4.9.3 Input signal timing chart . 22 4.10 OPTICS. 23 4.10.1 Optical characteristics. 23 4.10.2 Definition of contrast ratio. 24 4.10.3 Definition of luminance uniformity . 24 4.10.4 Definition of response times . 24 4.10.5 Definition of viewing angles. 24 5. RELIABILITY TESTS. 25 6. PRECAUTIONS . 26 6.1 MEANING OF CAUTION SIGNS . 26 6.2 CAUTIONS . 26 6.3 ATTENTIONS . 26 6.3.1 Handling of the product . 26 6.3.2 Environment. 27 6.3.3 Characteristics. 27 6.3.4 Other . 28 7. OUTLINE DRAWINGS . 29 7.1 FRONT VIEW . 29 7.2 REAR VIEW . 30 DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 3 NL10276BC16-01 NL10276BC16-01 1. OUTLINE 1.1 STRUCTURE AND PRINCIPLE Color LCD module NL10276BC16-01 NL10276BC16-01 is composed of the amorphous silicon thin film transistor liquid crystal display (a-Si TFT LCD) panel structure with driver LSIs for driving the TFT (Thin Film Transistor) array and a backlight. The a-Si TFT LCD panel structure is injected liquid crystal material into a narrow gap between the TFT array glass substrate and a color-filter glass substrate. Color (Red, Green, Blue) data signals from a host system (e.g. signal generator, etc.) are modulated into best form for active matrix system by a signal processing board, and sent to the driver LSIs which drive the individual TFT arrays. The TFT array as an electro-optical switch regulates the amount of transmitted light from the backlight assembly, when it is controlled by data signals. Color images are created by regulating the amount of transmitted light through the TFT array of red, green and blue dots. 1.2 APPLICATION · For industrial use 1.3 FEATURES · · · · · · · · · · · High resolution Ultra-wide viewing angle High contrast Wide color gamut LVDS interface Reversible-scan direction Selectable 8bit or 6bit digital signals for data of RGB Edge light type (without inverter) Replaceable lamp for backlight Acquisition product for UL60950-1/CSA UL60950-1/CSA C22.2 No.60950-1-03 (File number: E170632 E170632) Compliance with the European RoHS directive (2002/95/EC 2002/95/EC) (From product which was produced after April. 1, 2006) DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 4 NL10276BC16-01 NL10276BC16-01 2. GENERAL SPECIFICATIONS Display area 170.496 (H) × 127.872 (V) mm Diagonal size of display 21cm (8.4 inches) Drive system Pixel a-Si TFT active matrix 16,777,216 colors (At 8-bit input, FRC terminal= High) 262,144 colors (At 6-bit input, FRC terminal= Low or Open) 1,024 (H) × 768 (V) pixels Pixel arrangement RGB (Red dot, Green dot, Blue dot) vertical stripe Dot pitch 0.0555 (H) × 0.1665 (V) mm Pixel pitch 0.1665 (H) × 0.1665 (V) mm Module size 200.0 (W) × 152.0 (H) × 16.5 (D) mm (typ.) Weight 465 g (typ.) Contrast ratio 400:1 (typ.) Viewing angle At the contrast ratio 10:1 · Horizontal: Right side 85° (typ.), Left side 85° (typ.) · Vertical: Up side 85° (typ.), Down side 85° (typ.) Designed viewing direction At DPS= Low or open: normal scan · Viewing angle with optimum grayscale (=2.2): normal axis Polarizer surface Antiglare Polarizer pencil-hardness 3H (min.) [by JIS K5400 K5400] Color gamut At LCD panel center 72 % (typ.) [against NTSC color space] Response time Ton+Toff (10% 90%) 25 ms (typ.) Luminance At IBL= 5.0mArms / lamp 400 cd/m2 (typ.) Display color Signal system Power supply voltage Backlight LVDS 1port (Receiver: THC63LVDF84B THC63LVDF84B, THine Electronics Inc. or equivalent) 8bit/6bit digital signals for data of RGB colors, Dot clock (CLK), Data enable (DE) LCD panel signal processing board: 3.3V Edge light type: 4 cold cathode fluorescent lamps Replaceable part · Lamp holder set: Type No. 84LHS03 84LHS03 Recommended inverter (Option) · Inverter: Type No. 84PW021 84PW021 Power consumption At IBL=5.0mArms / lamp, Checkered flag pattern 9.8 W (typ., Power dissipation of the inverter is not included.) DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 5 NL10276BC16-01 NL10276BC16-01 3. BLOCK DIAGRAM Host D0+ LCD module (Product) 100 H-driver D0D1+ Controller with receiver for LVDS 100 D2D3+ 100 D3CLK+ 3,072 lines LCD panel V-driver D1D2+ 768 lines 100 H: 1,024 × 3 (R, G, B) V: 768 100 GND Note1 Note2 VCC FG Note1 Note2 Power supply for gradation Note3 51k CLKDPS FRC DC/DC converter Fuse LCD panel signal processing board Backlight (Edge light type) Metallic frame of lamp holder VBLH VBLH VDDB Inverter GNDB Note2 (Option) 2 lamps VBLC VBLH VBLH 2 lamps VBLC Note1 Metallic frame of lamp holder Note1: Relations between GND (Signal ground), FG (Frame ground) and VBLC (Lamp low voltage terminal) in the LCD module are as follows. GND - FG GND - VBLC FG - VBLC Not connected Not connected Not connected Note2: GND, FG and GNDB must be connected to customer equipment's ground, and it is recommended that these grounds are connected together in customer equipment. DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 6 NL10276BC16-01 NL10276BC16-01 Note3: Pull-down resistance of DPS pin (k) min. 20 typ. 50 max. 132 4. DETAILED SPECIFICATIONS 4.1 MECHANICAL SPECIFICATIONS Parameter Specification Unit 200.0 ± 0.5 (W) × 152.0 ± 0.5 (H) × 16.5 ± 0.5 (D) Module size Note1 Note1 170.496 (H) × 127.872 (V) Display area Weight mm mm 465 (typ.), 490 (max.) g Note1: See "7. OUTLINE DRAWINGS". 4.2 ABSOLUTE MAXIMUM RATINGS Parameter Power supply voltage Input voltage for signals Symbol Rating Unit LCD panel signal processing board VCC -0.3 to +4.0 V Lamp voltage VBLH 1,700 Vrms Display signals Note1 Function signal 1 Note2 Function signal 2 Note3 Remarks Ta = 25°C VD -0.3 to VCC+0.3 V Tst -20 to +60 °C - Front surface TopF 0 to +55 °C Note4 Rear surface TopR 0 to +65 °C Note5 95 % Ta 40°C 85 % 40 < Ta 50°C 70 % 50 < Ta 55°C 73 Note7 g/m3 Storage temperature VF1 VF2 Operating temperature Relative humidity Note6 Absolute humidity Note6 Note1: Note2: Note3: Note4: Note5: Note6: Note7: RH AH Ta > 55°C Display signals are D0+/-, D1+/-, D2+/-, D3+/- and CLK+/-. Function signal 1 is DPS. Function signal 2 is FRC. Measured at center of LCD panel surface (including self-heat) Measured at center of LCD module's rear shield surface (including self-heat) No condensation Water amount at Ta = 55°C and RH = 70% DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 7 NL10276BC16-01 NL10276BC16-01 4.3 ELECTRICAL CHARACTERISTICS 4.3.1 LCD panel signal processing board (Ta = 25°C) Parameter Symbol min. typ. max. Unit Remarks Power supply voltage VCC 3.0 3.3 3.6 V - Power supply current ICC - 300 Note1 450 Note2 mA at VCC = 3.3V Permissible ripple voltage VRP - - 100 mVp-p for VCC High VTH - - +100 mV Low VTL -100 - - mV RT - 100 - High VFH1 0.7VCC - VCC V Low VFL1 0 - 0.8 V High VFH2 2.0 - VCC V Low VFL2 0 - 0.8 V Differential input threshold voltage for LVDS receiver Terminating resistance Input voltage for DPS signal Input voltage for FRC signal at VCM=1.2V Note3 - - - Note1: Checkered flag pattern [by EIAJ ED-2522 ED-2522] Note2: Pattern for maximum current Note3: Common mode voltage for LVDS receiver DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 8 NL10276BC16-01 NL10276BC16-01 4.3.2 Backlight lamp (Ta = 25°C, Note1) Parameter Symbol min. typ. max. Unit Remarks Lamp current IBL 3.0 5.0 5.5 mArms at IBL=5.0mArms: 400cd/m2 Note3, Note4 Lamp voltage VBLH - 440 - Vrms Note2, Note3 875 - - Vrms 1,140 - - Vrms 49 54 59 kHz Lamp starting voltage VS Lamp oscillation frequency FO Ta = 25°C Note2, Note3, Note5, Note8 Ta = 0°C Note2, Note3, Note5, Note8 Note6 Note1: This product consists of 4 backlight lamps, and these specifications are for each lamp. Note2: The lamp voltage cycle between lamps should be kept on a same phase. "VS" and "VBLH" are the voltage value between low voltage side (Cold) and high voltage side (Hot). Note3: The asymmetric ratio of working waveform for lamps (Power supply voltage peak ratio, power supply current peak ratio and waveform space ratio) should be less than 5 % (See the following figure.). If the waveform is asymmetric, DC (Direct current) element apply into the lamp. In this case, a lamp lifetime may be shortened, because a distribution of a lamp enclosure substance inclines toward one side between low voltage terminal (Cold terminal) and high voltage terminal (Hot terminal). When designing the inverter, evaluate asymmetric of lamp working waveform sufficiently. |Pa - Pb| Pa Sa 0 × 100 5 % Pb Sb Pb |Sa - Sb| × 100 5 % Sb Pa: Supply voltage/current peak for positive, Pb: Supply voltage/current peak for negative Sa: Waveform space for positive part, Sb: Waveform space for negative part. Note4: This product's backlight consists of 2 lamp holders, and each lamp holder contains 2 lamps. 2 lamps are contained in the 1 lamp holder, and both lamps are connected to 1 low voltage cable. Lamp current must be 5.0mArms typical for each lamp, and sum of 2 lamps must be 10mArms typical. (with whole product: 20.0mArms) The lamp current should be measured by high-frequency current meter at the low voltage terminal. Note5: The inverter should be designed so that the lamp starting voltage can be maintained for more than 1 second. Otherwise the lamp may not be turned on. Note6: In case "FO" is not the recommended value, beat noise may display on the screen, because of interference between "FO" and "1/th". Recommended value of "FO" is as following. FO = 1 1 × (2n-1) × th 4 th: Horizontal cycle (See "4.9.2 Timing characteristics".) n : Natural number (1, 2, 3 ) DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 9 NL10276BC16-01 NL10276BC16-01 Note7: Method of lamp cable installation may invite fluctuation of lamp current and voltage or asymmetric of lamp working waveform. When designing method of lamp cable installation, evaluate the fluctuation of lamp current, voltage and working waveform sufficiently. Note8: In case of Inverter with Ballast condenser, "VS" is the voltage level between Ballast condenser and Connector (Refer to the below "Example of measurement"). "VS" should be designed to be more than minimum "VS". Otherwise the lamp may not be turned on because the lamp starting voltage is less than minimum "VS". Example of measurement Probe capacity: 3pF (Tektronix, inc.: P6015A P6015A) Ballast condenser (Lamp side) VS High voltage probe Connector Transformer Probe capacity Inverter 4.3.3 Power supply voltage ripple This product works, even if the ripple voltage levels are beyond the permissible values as following the table, but there might be noise on the display image. Ripple voltage Note1 (Measure at input terminal of power supply) VCC Unit 100 Power supply voltage mVp-p 3.3V Note1: The permissible ripple voltage includes spike noise. 4.3.4 Fuse Fuse Parameter Rating Type VCC FCC16132AB FCC16132AB KAMAYA ELECTRIC Co., Ltd. Fusing current Remarks 2.5A Note1 Supplier 1.25A 32V Note1: The power supply capacity should be more than the fusing current. If it is less than the fusing current, the fuse may not blow in a short time, and then nasty smell, smoke and so on may occur. DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 10 NL10276BC16-01 NL10276BC16-01 4.4 POWER SUPPLY VOLTAGE SEQUENCE 4.4.1 LCD panel signal processing board OFF ON VCC Note1 ON 3.0V 0.3V 0V 10s Tr < 50ms Toff 50ms Display signals* Function signals Note2 0V VALID period 0ms < t < 35ms 0ms < t < 35ms * These signals should be measured at the terminal of 100 resistance. Note1: In terms of voltage variation (voltage drop) while VCC rising edge is below 3.0V, a protection circuit may work, and then this product may not work. Note2: Display signals (D0+/-, D1+/-, D2+/-, D3+/- and CLK+/-) and function signals (DPS and FRC) must be Low or High-impedance, exclude the VALID period (See above sequence diagram), in order to avoid that internal circuits is damaged. If some of display and function signals of this product are cut while this product is working, even if the signal input to it once again, it might not work normally. If customer stops the display and function signals, they should be cut VCC. 4.4.2 Inverter (Option) Note2 Display and function signals Note1 VALID period VDDB Note1: These are the display and function signals for LCD panel signal processing board. Note2: The backlight should be turned on within the valid period of display and function signals, in order to avoid unstable data display. DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 11 NL10276BC16-01 NL10276BC16-01 4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS 4.5.1 LCD panel signal processing board CN1 socket (LCD module side): FI-SE20P-HFE FI-SE20P-HFE (Japan Aviation Electronics Industry Limited (JAE) Adaptable plug: FI-S20S FI-S20S (Japan Aviation Electronics Industry Limited (JAE) Pin No. Symbol A 1 D3+ Signal Pixel data B Pixel data GND Note1, Note3 Ground D3- B 3 GND A 2 Remarks Note4 Ground Note1, Note3 High: Low or Open: High: Low or Open: Note4 Reverse scan Normal scan Frame rate control ON Frame rate control OFF DPS Selection of scan direction 4 FRC Selection signal of frame rate control 5 GND Ground Note4 6 CLK+ Pixel clock Note3 7 CLK- 8 GND Ground Note4 9 D2+ Pixel data Note3 10 D2- 11 GND Ground Note4 12 D1+ Pixel data Note3 13 D1- 14 GND Ground Note4 15 D0+ Pixel data Note3 16 D0- 17 GND Ground Note4 18 GND 19 VCC Power supply Note4 20 VCC Note2 Note1 Note1: See "4.6 DISPLAY COLORS AND INPUT DATA SIGNALS". Note2: See "4.8 SCANNING DIRECTIONS". Note3: Twist pair wires with 100 (Characteristic impedance) should be used between LCD panel signal processing board and LVDS transmitter. Note4: All GND and VCC terminals should be used without any non-connected lines. Note5: See "4.5.4 Connection between receiver and transmitter for LVDS". DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 12 NL10276BC16-01 NL10276BC16-01 4.5.2 Backlight lamp Attention: VBLH and VBLC must be connected correctly. Wrong connections will cause electric shock and also break down of the product. CN2 plug (LCD module side): Adaptable socket: Pin No. 1 2 3 4 BHR-04VS-1 BHR-04VS-1 (J.S.T Mfg. Co., Ltd.) SM03 (7-D1) B-BHS-1-TB (LF)(SN) SM03 (7-D1) B-BHS-1-TB (J.S.T Mfg. Co., Ltd.) Symbol VBLH VBLH N. C. VBLC Signal High voltage (Hot) High voltage (Hot) Low voltage (Cold) CN3 plug (LCD module side): Adaptable socket: Pin No. 1 2 3 4 Remarks Cable color: White Cable color: White Keep this pin Open. Cable color: Black BHR-04VS-1 BHR-04VS-1 (J.S.T Mfg. Co., Ltd.) SM03 (7-D1) B-BHS-1-TB (LF)(SN) SM03 (7-D1) B-BHS-1-TB (J.S.T Mfg. Co., Ltd.) Symbol VBLH VBLH N. C. VBLC Signal High voltage (Hot) High voltage (Hot) Low voltage (Cold) Remarks Cable color: White Cable color: White Keep this pin Open. Cable color: Black 4.5.3 Positions of plug and socket Low voltage (Cold) Rear side 4 CN2 2 1 High voltage caution marking Barcode label Nameplate label High voltage (Hot) Disposal method marking for lamp High voltage (Hot) CN3 1 1 2 CN1 20 4 Low voltage (Cold) Insert direction DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 13 NL10276BC16-01 NL10276BC16-01 4.5.4 Connection between receiver and transmitter for LVDS (1) Input data signal: 8bit Host Note2 LCD module (Product) Note3 R2 TA0 TD+ R3 TA1 TD- R4 TA2 R5 TA3 R6 R7 G2 GND D3+ RD+ 2A D3- RD- TA4 3 DPS TA5 4 FRC TA6 5 GND TCLK+ 6 CLK+ RCLK+ TCLK- 7 CLK- RCLK- 1A G3 TB0 G4 TB1 8 GND G5 TB2 TC+ 9 D2+ RC+ G6 TB3 TC- 10 D2- RC- G7 TB4 11 GND B2 TB5 TB+ 12 D1+ RB+ B3 TB6 TB- 13 D1- RB- 14 GND B4 TC0 TA+ 15 D0+ RA+ B5 TC1 TA- 16 D0- RA- B6 TC2 17 GND B7 TC3 18 GND Note4 TC4 19 VCC Note4 TC5 20 VCC DE TC6 Signal processor Receiver for LVDS Equivalent of THC63LVDF84B THC63LVDF84B CN1 R0 TD0 R1 TD1 G0 TD2 G1 TD3 B0 TD4 B1 TD5 Note4 FRC TD6 CLK DPS VCC CLK IN LVDS transmitter THC63LVDM83R THC63LVDM83R or equivalent Note1 VCC LCD controller GND LCD panel signal processing board GND DPS FRC (High) Note1: Recommended transmitter THC63LVDM83R THC63LVDM83R (THine Electronics Inc.) or equivalent Note2: LSB (Least Significant Bit) - R0, G0, B0 MSB (Most Significant Bit) - R7, G7, B7 Note3: Twist pair wires with 100 (Characteristic impedance) should be used between LCD panel signal processing board and LVDS transmitter. Note4: Input signals to TC4, TC5 and TD6 are not used inside the product, but do not keep TC4, TC5 and TD6 open to avoid noise problem. DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 14 NL10276BC16-01 NL10276BC16-01 (2) Input data signal: 6bit Host LCD module (Product) Note2 R0 TA0 GND Note3 R1 TA1 R2 TA2 1B GND R3 TA3 2B GND R4 TA4 3 DPS R5 TA5 4 FRC G0 TA6 5 GND 6 CLK+ RCLK+ 7 CLK- RCLK- TCLK+ TCLK- G1 TB0 G2 TB1 8 GND G3 TB2 TC+ 9 D2+ RC+ G4 TB3 TC- 10 D2- RC- G5 TB4 B0 TB5 TB+ B1 TB6 TB- B2 TC0 TA+ B3 TC1 TA- B4 TC2 B5 TC3 Note4 TC4 Note4 TC5 DE TC6 Signal processor 11 GND 12 D1+ RB+ 13 D1- RB- 14 GND 15 D0+ RA+ 16 D0- RA- 17 GND 18 GND 19 VCC 20 VCC Receiver for LVDS Equivalent of THC63LVDF84A THC63LVDF84A CN1 CLK FRC CLK IN DPS VCC LCD controller GND VCC LVDS transmitter THC63LVDM83R THC63LVDM83R or equivalent Note1 GND LCD panel signal processing board DPS FRC (Low or Open) Note1: Recommended transmitter THC63LVDM83R THC63LVDM83R (THine Electronics Inc.) or equivalent Note2: LSB (Least Significant Bit) ­ R0, G0, B0 MSB (Most Significant Bit) ­ R5, G5, B5 Note3: Twist pair wires with 100 (Characteristic impedance) should be used between LCD panel signal processing board and LVDS transmitter. Note4: Input signals to TC4 and TC5 are not used inside the product, but do not keep TC4 and TC5 open to avoid noise problem. DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 15 NL10276BC16-01 NL10276BC16-01 4.6 DISPLAY COLORS AND INPUT DATA SIGNALS 4.6.1 Combinations between input data signals and FRC signal This product can display in equivalent to 16,777,216 colors in 256 gray scales and 262,144 colors in 64 gray scales by combination between input data signals and FRC signal. See following table. Combination Input data signals CN1-Pin No.1 and 2 FRC signal Display colors Remarks 8bit D3+/- High 16,777,216 Note1 6bit GND Low or Open 262,144 Note2 Note1: See "4.6.2 16,777,216 colors". Note2: See "4.6.3 262,144 colors". DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 16 NL10276BC16-01 NL10276BC16-01 4.6.2 16,777,216 colors This product can display equivalent of 16,777,216 colors in 256 gray scales by combination . (See "4.6.1 Combinations between input data signals and FRC signal".) Also the relation between display colors and input data signals is as the following table. Basic Colors Display colors Black Blue Red Magenta Green Cyan Yellow White Red gray scale Black dark bright Red Green gray scale Black dark bright Green Blue gray scale Black dark bright Blue Data signal (0: Low level, 1: High level) R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 1 0 0 1 1 0 0 1 1 0 1 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 1 1 1 1 1 1 0 1 1 1 0 1 : : 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : : : 0 0 0 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 1 1 1 0 0 0 : : 0 0 0 0 0 0 0 1 1 1 1 0 0 0 : : : : 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 : : : : 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 17 NL10276BC16-01 NL10276BC16-01 4.6.3 262,144 colors This product can display equivalent of 262,144 colors in 64 gray scales by combination . (See "4.6.1 Combinations between input data signals and FRC signal".) Also the relation between display colors and input data signals is as the following table. Basic colors Display colors Black Blue Red Magenta Green Cyan Yellow White Red gray scale Black dark bright Red Green gray scale Black dark bright Green Blue gray scale Black dark bright Blue Data signal (0: Low level, 1: High level) R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 1 0 0 1 1 0 0 1 1 0 1 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 1 1 1 0 1 1 1 0 1 : : 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 : : : : 0 0 0 0 1 0 1 0 1 0 1 0 0 0 : : 0 0 0 0 0 0 1 1 1 0 0 0 : : 0 0 0 0 0 0 0 1 1 1 1 0 0 0 : : : : 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 : : : : 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 18 NL10276BC16-01 NL10276BC16-01 4.7 DISPLAY POSITIONS The following table is the coordinates per pixel (See "4.8 SCANNING DIRECTIONS".). C (0, 0) R G C( 0, 0) C( 0, 1) C( 0, Y) C( 0, 766) C( 0, 767) B C( 1, 0) C( 1, 1) C( 1, Y) C( 1, 766) C( 1, 767) C( C( X, 0) X, 1) C( X, Y) C( X, 766) C( X, 767) C(1022, 0) C(1022, 1) C(1022, Y) C(1022, 766) C(1022, 767) C(1023, 0) C(1023, 1) C(1023, Y) C(1023, 766) C(1023, 767) 4.8 SCANNING DIRECTIONS The following figures are seen from a front view. Also the arrow shows the direction of scan. C (0, 0) D (0, 0) C (1023, 0) D (1023, 0) Note1 C (0,767) D (0,767) C (1023, 767) D (1023, 767) Figure 1. Normal scan (DPS: Low or Open) C (0, 0) D (1023, 767) C (1023, 0) D (0, 767) Note1 C (0,767) D (1023, 0) C (1023, 767) D (0, 0) Figure 2. Reverse scan (DPS: High) Note1: Meaning of C (X, Y) and D (X, Y) C (X, Y): The coordinates of the display position (See "4.7 DISPLAY POSITIONS".) D (X, Y): The data number of input signal for LCD panel signal processing board DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 19 NL10276BC16-01 NL10276BC16-01 4.9 INPUT SIGNAL TIMINGS 4.9.1 Outline of input signal timings · Horizontal signal Note1 Horizontal display period (thd) DE (Data enable) Display period · Vertical signal Note1 Vertical display period (tvd) DE (Data enable) 1 2 3 4 Display period 768 Note2 Note1: This diagram indicates virtual signal for set up to timing. Note2: See "4.9.3 Input signal timing chart" for numeration of pulse. DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 20 NL10276BC16-01 NL10276BC16-01 4.9.2 Timing characteristics (Note1, Note2) Parameter CLK DATA Symbol Frequency Duty Rise time, Fall time Setup time CLK-DATA Hold time Rise time, Fall time min. typ. max. Unit Remarks 1/tc - 60.0 65.0 68.0 MHz ns ns ns ns 15.385 ns (typ.) DE Vertical (One frame) CLK-DE th Display period Horizontal Cycle tv Display period Setup time tvd - 19.67 20.676 22.4 - 1,344 1,024 16.666 806 768 - thd Cycle - Hold time Rise time, Fall time - 13.3 780 - 18.5 - s CLK CLK ms H H ns ns ns - - 48.363 kHz (typ.) 60.0 Hz (typ.) - Note1: Definition of parameters is as follows. tc = 1CLK, th = 1H Note2: See the data sheet of LVDS transmitter. DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 21 NL10276BC16-01 NL10276BC16-01 4.9.3 Input signal timing chart Horizontal timing tc CLK DATA (R0-R5) (G0-G5) (B0-B5) INVALID 1 2 1023 1024 INVALID DE thd th Vertical timing DATA (R0-R5) (G0-G5) (B0-B5) INVALID INVALID 1 2 767 768 DE tvd tv DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 22 NL10276BC16-01 NL10276BC16-01 4.10 OPTICS 4.10.1 Optical characteristics (Note1, Note2) Parameter Symbol Condition White at center R = 0°, L = 0°, U = 0°, D = 0° White/Black at center Contrast ratio R = 0°, L = 0°, U = 0°, D = 0° White Luminance uniformity R = 0°, L = 0°, U = 0°, D = 0° x coordinate White y coordinate x coordinate Red y coordinate Chromaticity x coordinate Green y coordinate x coordinate Blue y coordinate R = 0°, L = 0°, U = 0°, D = 0° Color gamut at center, against NTSC color space Black to white Response time White to black Right U = 0°, D = 0°, CR 10 Left U = 0°, D = 0°, CR 10 Viewing angle Up R = 0°, L = 0°, CR 10 Down R = 0°, L = 0°, CR 10 Luminance min. typ. max. Unit Measuring instrument L 300 400 - cd/m2 BM-5A - CR 300 400 - - BM-5A Note3 LU - 1.25 1.40 - BM-5A Note4 Wx Wy Rx Ry Gx Gy Bx By 0.270 0.285 - 0.300 0.315 0.643 0.332 0.288 0.613 0.142 0.084 0.330 0.345 - - SR-3 Note5 C 65 72 - % Ton Toff R L U D 70 70 70 70 13 12 85 85 85 85 17 15 - ms ms ° ° ° ° BM-5A Note6 Note7 BM-5A Note8 Remarks Note1: These are initial characteristics. Note2: Measurement conditions are as follows. Ta = 25°C, VCC = 3.3V, IBL = 5.0mArms/lamp, Display mode: XGA, Horizontal cycle = 1/48.363kHz, Vertical cycle = 1/60.0Hz, DPS= Low or Open, FRC= Low or Open Optical characteristics are measured at luminance saturation after 20minutes from working the product, in the dark room. Also measurement methods are as follows. 50cm Photodetector (BM-5A or SR-3) LCD module (Product) Note3: Note4: Note5: Note6: Note7: Note8: 1° See "4.10.2 Definition of contrast ratio". See "4.10.3 Definition of luminance uniformity". These coordinates are found on CIE 1931 chromaticity diagram. Product surface temperature: TopF = 35°C See "4.10.4 Definition of response times". See "4.10.5 Definition of viewing angles". DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 23 NL10276BC16-01 NL10276BC16-01 4.10.2 Definition of contrast ratio The contrast ratio is calculated by using the following formula. Contrast ratio (CR) = Luminance of white screen Luminance of black screen 4.10.3 Definition of luminance uniformity The luminance uniformity is calculated by using following formula. Maximum luminance from to Minimum luminance from to Luminance uniformity (LU) = The luminance is measured at near the 5 points shown below. 171 512 853 128 384 640 4.10.4 Definition of response times Response time is measured, the luminance changes from " black " to " white ", or " white " to " black " on the same screen point, by photo-detector. Ton is the time it takes the luminance change from 10% up to 90%. Also Toff is the time it takes the luminance change from 90% down to 10% (See the following diagram.). White 100% 90% Luminance Black 10% 0% Ton Toff 4.10.5 Definition of viewing angles Normal axis (Perpendicular) 12 o'clock L U Left Upper R D Lower Right DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 24 NL10276BC16-01 NL10276BC16-01 5. RELIABILITY TESTS Test item Condition High temperature and humidity (Operation) Judgement 60 ± 2°C, RH = 60%, 240hours Display data is white. 0 ± 3°C.1hour 55 ± 3°C.1hour 50cycles, 4hours/cycle Display data is white. Heat cycle (Operation) Thermal shock (Non operation) -20 ± 3°C.30minutes 60 ± 3°C.30minutes 100cycles, 1hour/cycle Temperature transition time is within 5 minutes. No display malfunctions Note1 150pF, 150, ±10kV 9 places on a panel surface Note2 10 times each points at 1 sec interval ESD (Operation) Dust (Operation) Vibration (Non operation) Mechanical shock (Non operation) Sample dust: No. 15 (by JIS-Z8901 JIS-Z8901) 15 seconds stir 8 times repeat at 1 hour interval 5 to 100Hz, 11.76m/s2 1 minute/cycle X, Y, Z direction 10 times each directions 294m/ s2, 11ms ±X, ±Y, ±Z direction 3 times each directions No display malfunctions No physical damages Note1 Note1: Display and appearance are checked under environmental conditions equivalent to the inspection conditions of defect criteria. Note2: See the following figure for discharge points. DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 25 NL10276BC16-01 NL10276BC16-01 6. PRECAUTIONS 6.1 MEANING OF CAUTION SIGNS The following caution signs have very important meaning. Be sure to read "6.2 CAUTIONS" and "6.3 ATTENTIONS", after understanding these contents! ! This sign has the meaning that customer will be injured by himself or the product will sustain a damage, if customer has wrong operations. This sign has the meaning that customer will get an electrical shock, if customer has wrong operations. This sign has the meaning that customer will be injured by himself, if customer has wrong operations. 6.2 CAUTIONS Do not touch the working backlight. There is a danger of an electric shock. Do not touch the working backlight. There is a danger of burn injury. Do not shock and press the LCD panel and the backlight! There is a danger of breaking, because they are made of glass. (Shock: To be not greater 294m/s2 and to be not greater 11ms, Pressure: To be not greater 19.6 N (16mm jig) 6.3 ATTENTIONS ! 6.3.1 Handling of the product Take hold of both ends without touching the circuit board when the product (LCD module) is picked up from inner packing box to avoid broken down or misadjustment, because of stress to mounting parts on the circuit board. Do not hook nor pull cables such as lamp cable, and so on, in order to avoid any damage. When the product is put on the table temporarily, display surface must be placed downward. When handling the product, take the measures of electrostatic discharge with such as earth band, ionic shower and so on, because the product may be damaged by electrostatic. The torque for product mounting screws must never exceed 0.49Nm. Higher torque might result in distortion of the bezel. The product must be installed using mounting holes without undue stress such as bends or twist (See outline drawings). And do not add undue stress to any portion (such as bezel flat area). Bends or twist described above and undue stress to any portion may cause display mura. Do not press or rub on the sensitive product surface. When cleaning the product surface, use of the cloth with ethanolic liquid such as screen cleaner for LCD is recommended. DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 26 NL10276BC16-01 NL10276BC16-01 Do not push nor pull the interface connectors while the product is working. Do not bend or unbend the lamp cable at the near part of the lamp holding rubber, to avoid the damage for high voltage side of the lamp. Properly connect the plug (backlight side) to adaptable socket (inverter side) without incomplete connection. After connecting, be careful not to hook the lamp cables because incomplete connection may occur by hooking the lamp cables. This incomplete connection may cause abnormal operation of high voltage circuit. If the lamp cable is attached on the metal part of the product directly, high frequency leak current to the metal part may occur, then the brightness may decrease or the lamp may not be turned on. When not connecting FG of the LCD module to the customer's equipment ground, inverter noise may create video noise on the LCD screen. When handling the product, use of an original protection sheet on the product surface (polarizer) is recommended for protection of product surface. Adhesive type protection sheet may change color or characteristics of the polarizer. Usually liquid crystals don't leak through the breakage of glasses because of the surface tension of thin layer and the construction of LCD panel. But, if you contact with liquid crystal for the worst, please wash it out with soap. 6.3.2 Environment Do not operate or store in high temperature, high humidity, dewdrop atmosphere or corrosive gases. Keep the product in packing box with antistatic pouch in room temperature to avoid dusts and sunlight, when storing the product. In order to prevent dew condensation occurring by temperature difference, the product packing box should be opened after enough time being left under the environment of an unpacking room. Evaluate the leaving time sufficiently because a situation of dew condensation occurring is changed by the environmental temperature and humidity. (Recommended leaving time: 6 hours or more with packing state) Do not operate in high magnetic field. Circuit boards may be broken down by it. This product is not designed as radiation hardened. 6.3.3 Characteristics The following items are neither defects nor failures. Response time, luminance and color may be changed by ambient temperature. Display mura, flicker, vertical seam or small spot may be observed depending on display patterns. Optical characteristics (e.g. luminance, display uniformity, etc.) gradually is going to change depending on operating time, and especially low temperature, because the LCD has cold cathode fluorescent lamps. Do not display the fixed pattern for a long time because it may cause image sticking. Use a screen saver, if the fixed pattern is displayed on the screen. The display color may be changed depending on viewing angle because of the use of condenser sheet in the backlight. Optical characteristics may be changed depending on input signal timings. The interference noise between input signal frequency for this product's signal processing board and luminance control frequency of the inverter may appear on a display. Set up luminance control frequency of the inverter so that the interference noise does not appear. After the product is stored under condition of low temperature or dark place for a long time, the cold cathode fluorescent lamp may not be turned on under the same condition because of the general characteristic of cold cathode fluorescent lamp. In addition, when Luminance control ratio is low in pulse width modulation method inverter, the lamp may not be turned on. In this case, power should be supplied again. DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 27 NL10276BC16-01 NL10276BC16-01 6.3.4 Other All GND and VCC terminals should be used without any non-connected lines. Do not disassemble a product or adjust variable resistors. See "REPLACEMENT MANUAL FOR LAMP HOLDER SET", when replacing backlight lamps. Pay attention not to insert foreign materials inside of the product, when using tapping screws. Pack the product with original shipping package, in order to avoid any damages during transportation, when returning the product to NEC for repair and so on. DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) 28 NL10276BC16-01 NL10276BC16-01 7. OUTLINE DRAWINGS 7.1 FRONT VIEW Note1: The values in parentheses are for reference. Note2: The torque for product mounting screws must never exceed 0.49Nm. Note3: Mounting hole portions (4 pieces) DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) Unit: mm 29 NL10276BC16-01 NL10276BC16-01 7.2 REAR VIEW Note1: The values in parentheses are for reference. Note2: The torque for product mounting screws must never exceed 0.49Nm. DATA SHEET DOD-PP-0232 DOD-PP-0232 (5th edition) Unit: mm 30