MSM7730 80C186 V33HL LQFP144-P-2020-0 V30HL 93C46 93C56 93C66 PMB2306T UMA1020N - Datasheet Archive

 

O K I L O G I C P R O D U C T S MSM7730 Wireless LAN Baseband Controller June 1998 s s

 

DATA SHEET O K I L O G I C P R O D U C T S MSM7730 MSM7730 Wireless LAN Baseband Controller June 1998 s s ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Description .3 Features .3 Block Diagram . 4 Interface Descriptions .4 Processor Interface .4 Shared RAM Interface .5 EEPROM Interface .6 Host Interface (Between Adapter Card and Computer or Laptop) .6 Radio Interface .7 MODEM Interface .8 Modulator .8 Demodulator .9 PHY Interface .10 PCMCIA Interface .11 Pin Configuration. 12 Pin Descriptions . 13 MSM7730 MSM7730 Register MAP . 17 0 Oki Semiconductor MSM7730 MSM7730 Wireless LAN Baseband Controller DESCRIPTION The MSM7730 MSM7730 is Oki's second generation of wireless local area network (LAN) baseband controllers designated ".XI" (a suffix of the IEEE P802.11 protocol). The MSM7730 MSM7730 integrates the baseband physical layer (PHY) and the lower medium access controller (MAC) layers into a single device that supports the IEEE 802.11 specification. The MSM7730 MSM7730 supports frequency hopping (FH), spread spectrum, directsequence spread spectrum (DSSS), and infrared (IR) protocols. Portable hand-held systems require minimal current dissipation during normal and standby modes. The addition of new hibernate and smart-hibernate power-down modes lowers power consumption to 2 mA. Two voltages are required for the MSM7730 MSM7730; 3.3 V for the core, and 5 V for the input/output (I/O) interface. The MSM7730 MSM7730 is manufactured using Oki's advanced Si-gate 0.5µm complementary metal-oxide semiconductor (CMOS) process. MSM7730 MSM7730 firmware is available from Oki Semiconductor. FEATURES · Complies with IEEE P802.11 wireless LAN standards. · Hibernate power savings mode substantially reduces power consumption in battery applications. · Access point contention-free mode simplifies time-bound service. · Single antenna diversity mode lowers system costs. · Suitable for low-cost stations and access points. · Personal Computer Memory Card International Association (PCMCIA)-compliant (Version 2.1) interface supporting 16-bit data transfers. · On-chip radio modem for high-throughput data transfers. · Processor interface support for 80C186 80C186, V33HL V33HL, and V53A. · On-chip multi-port memory controller on chip for local shared memory and simplified design construction. · EEPROM interface for downloading configuration information and nonvolatile storage. · 5-V external and 3.3-V core operation. · Provides seamless interface to the radio, host, processor, and memory subsystems · Modem bypass mode supports IR and DS. · 144-pin LQFP package, suitable for PCMCIA Type II Cards (LQFP144-P-2020-0 LQFP144-P-2020-0.50-K). Oki Semiconductor 1 s MSM7730 MSM7730 s ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ BLOCK DIAGRAM Figure 1 shows a typical wireless LAN (WLAN) card. The MSM7730 MSM7730 provides a direct connection to a host interface, processor, radio, shared memory, and configuration EEPROM. The optional addition is a processor RAM for code storage. MSM7730 MSM7730 PHY Layer, Radio Interface Radio Combined 1 & 2 Mbps Modem Processor RAM (optional) MAC Protocol Controller Host Computer PCMCIA Interface Processor Interface Memory Controller EEPROM Interface Processor Shared RAM (32k~128kx16) EEPROM Figure 1. MSM7730 MSM7730 Block Diagram and Typical WLAN Card INTERFACE DESCRIPTIONS The MSM7730 MSM7730 provides the following interfaces: · · · · · · · Processor Shared RAM EEPROM Radio MODEM PHY PCMCIA These interfaces are explained in the following subsections. Processor Interface Most applications require a local processor to handle the higher layers of the IEEE 802.11 protocol. The host computer typically runs a network device/driver interface specification (NDIS) or open datalink interface (ODI) driver that communicates to the local processor via shared memory and interrupts. The local processor performs the higher layers of the IEEE 802.11 MAC protocol while the MSM7730 MSM7730 performs the lower layers of MAC and the PHY under control of the local processor. 2 Oki Semiconductor ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ s MSM7730 MSM7730 s The MSM7730 MSM7730 can be configured to operate with V30HL V30HL, V53A, and 80C186 80C186 processor types. The processor configuration is determined from the P_CONF field in the Device Configuration register. The following table shows how each processor is selected. No external circuitry is required between the processor and the MSM7730 MSM7730. Selecting the Processor Mode P_CONF 2:0 Processor Mode 000 Host-only mode. No local processor. 001 V30HL V30HL local processor mode. 010 80C186 80C186 local processor mode. 011 Reserved 100 V53A local processor mode. In each processor mode, the bus interface module: · Interprets the external bus cycles · Generates the appropriate signals based on the processor mode, · Passes access requests to the host interface module, the shared RAM arbiter, and the baseband registers. The module also synchronizes data and control signals to the internal clocks, and interfaces the external processor to the host interface and processor interrupt control modules. The 80C186 80C186 and V53A processors contain their own clock generator modules and divide-by logic. In these modes, the MSM7730 MSM7730 generates a clock (X1) at twice the normal operating frequency. The processor divides this frequency by two (X1/2). Then this clock is used for synchronization of all interface signals. In V30HL V30HL processor mode, the MSM7730 MSM7730 generates the clocks for the internal modules as well as the processor. A 16-MHz clock is used during normal operation. This frequency is reduced when the MSM7730 MSM7730 enters either the Hibernate or Smart Hibernate modes. In Hibernate mode the clock frequency is reduced from 16 MHz to 500 KHz. In Smart Hibernate mode the frequency is reduced to 125 KHz. Shared RAM Interface A shared memory interface is provided for the buffering of packets and the storage of processor code and data. Memory sizes range from 32K words to 128K words in 32K-word increments. Both 16-bit (word) and 8-bit memory accesses are supported. The MSM7730 MSM7730 and the host computer support only word accesses to memory. The processor supports both byte and word accesses to memory. Selection of byte or word transfers occurs on a per-cycle basis and depends on the state of address bit 0 (PD[0]) and the PUBEN signal as shown in the table below. Selecting the Data Transfer Size PD[0] PUBEN 0 0 Word transferred on PD[15:0] Transfer Type 0 1 Even byte transferred on PD[7:0] 1 0 Odd byte transferred on PD[15:8] 1 1 Invalid Oki Semiconductor 3 s MSM7730 MSM7730 s ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ For cost-sensitive applications, local processor code may reside in shared memory. However, this may affect processor because accesses to shared memory may contain wait states. EEPROM Interface EEPROM support is provided for nonvolatile storage of host interface configuration (e.g., PCMCIA CIS table) and WLAN parameters (e.g., local IEEE address, radio parameters). The MSM7730 MSM7730 supports 64-, 128- or 256-byte EEPROM sizes (e.g., 93C46 93C46, 93C56 93C56, or 93C66 93C66 types). . V MSM7730 MSM7730 EECS SYNCLK/EESK SYNDAT/EEDIO CS SK DI DO V 93c46 93c58 94s66 V Figure 2. EEPROM Connections to MSM7730 MSM7730 The local processor can be used to initialize the EEPROM and control read and writes accesses for providing card parameter storage. Following a reset by the host processor, the EEPROM contents are automatically transferred to shared RAM to provide the configuration information for the host interface. If the device is configured in PCcard host mode, either 64 or 128 bytes are downloaded to shared RAM to provide the Configuration Information Structure (CIS). If the device is configured in industry standard architecture (ISA) host mode, a single word is loaded into an internal register to determine the ISA address space mapping and interrupt configuration information. Host Interface (Between Adapter Card and Computer or Laptop) The 16-bit PCMCIA interface is fully supported by the MSM7730 MSM7730 with no additional logic. Access to attribute memory (CIS configuration data) and I/O memory (host registers) are provided. During normal operation, I/O addresses are used to access the baseband controller registers and shared memory. 4 Oki Semiconductor ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ s MSM7730 MSM7730 s Radio Interface The radio interface supports simple, flexible control of the radio and its synthesizer. The control signal timing is programmable by the processor. Figure 3 shows the connection to a typical radio architecture. Radio MSM7730 MSM7730 LNA RADPWR RXC1 SLICE RXD Disc RSSITH CSN DAC D T/R Switch Diversity Switching + - DACEN SYNCLK SYNDAT SYNLEN LKDET 1LO 2LO PA DAC IFD[5:0] TXC1 TXC2 ANT Figure 3. Typical FH Radio Interface The MSM7730 MSM7730 uses the RXC1 and TXC[1:0] pins to control radio timing. The delay between these signals is programmable to support different radio designs. The MSM7730 MSM7730 provides a 24-bit serial programming interface that supports the Seimens PMB2306T PMB2306T and Philips UMA1020N UMA1020N synthesizers. The synthesizer interface is controlled through the use of an on-chip synthesizer register. The MSM7730 MSM7730 provides a hardware controlled serial DAC interface that is not accessible through any MSM7730 MSM7730 registers. Because the synthesizer and EEPROM share the same clock and data lines, software is responsible for ensuring that the PHY module is disabled when either of these modules is accessed. At the start of each transmit packet, one of the four power levels is selected from the on-chip power control register according to the transmit power level requested by the control word of that packet. During a receive operation, the serial DAC is used together with an external comparator for RSSI thresholds and successive approximation measurement. The RSSIA threshold is loaded whenever the receiver is first powered on. Once the RSSIA threshold is exceeded, the demodulator is accessed and the RSSIB, RSSIC, and RSSID thresholds are loaded sequentially during each antenna scan. Once antenna scanning has completed, a successive approximation is started. Oki Semiconductor 5 s MSM7730 MSM7730 s ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ MODEM Interface The MSM7730 MSM7730 provides Frequency Hopping Physical Layer Convergence Protocol (FH PLCP) framing and the FH modem as defined by the IEEE 802.11 specification. The radio synthesizer control pins are used for all modem options. A diagnostic port is provided when the internal modem is used. Several options are provided by the internal FH modem. The following table shows the pin usage for the various modem options. Modem Options and Pin Connections [1] FH Mbps (Low Cost) Modem Interface FH 1/2 Mbps (Normal ADC) FH 1/2 Mbps (Delta ADC) MSEL 1 2 3 IFD[5:0] IFD[5:0] to TXIF DAC IFD[4] carries SLICE on RX IFD[5:0] to TXIF DAC and IFD[3:0] from RXADC IFD[5:0] to TXIF DAC (also used for Delta ADC) RXD Baseband RX data from radio Recovered data (Debug out) Input from Delta ADC comparator 1. All modem signals are synchronized to RCK. Modulator The MSM7730 MSM7730 provides an integrated 24-MHz internal digital IF modulator. The modulator generates ordinary Frequency Shift Keying (CP-FSK) and relies on radio filtering to shape this to Gaussian Frequency Shift Keying (GFSK). Since the radio requires a SAW filter to achieve out-of-band transmit requirements, this filter can also be used to provide the required in-band frequency response. This provides for more efficient power consumption because extra digital filtering is not required in the modulator. The modulator is shown in Figure 4. TxData TxClkEn Input Processing Modulator Ramp Processing IFData RADIO PHY Mode ModeEn State Machine Figure 4. Modulator Block Diagram The modulator supports two modes of modulator operation: · 1-Mbps, 2-ary CP-FSK · 2-Mbps, 4-ary CP-FSK The modulation scheme for 1-Mbps operation is Gaussian Frequency Shift Keying (GFSK). The modulation scheme for 2-Mbps operation is 4-level GFSK. Deviations can be set independently for both modes. Modes switch phase continuously in a single clock cycle. · 1-Mb deviation: 1MDEV = N x 326 /4096 Hz · 2-Mb deviation: 2MDEV = N x 3 x 326/4096 Hz where N = 0.63. 6 Oki Semiconductor ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ s MSM7730 MSM7730 s Digital on/off ramping from 0 to 24 µs of the modulator output power may be added under register control Modulator radio requirements are: · 6-bit DAC, clock at 32 MHz (offset binary, 2's complement) · Anti-alias filtering to extract the 24-MHz alias (24-MHz IF will be -10 dB on 8-MHz fundamental from DAC output) · Gaussian filtering to translate CP-FSK into G-FSK, in accordance with the IEEE 802.11 specification (SAW filter at 240 MHz, if recommended) Demodulator The baseband controller in the MSM7730 MSM7730 incorporates a digital baseband demodulator designed to demodulate IEEE 802.11 GFSK data packets with 1- and 2-Mbps headers. The demodulator contains the following features: · · · · · · 1- and 2-Mbps operation Two-antenna diversity control Analog discriminator interface Flexible clear channel assessment (CCA) options to enhance interference performance Tunable or adaptive digital filter and data slicers for performance optimization Clock and carrier tracking for demodulation of long data packets State Machine Dev Detect Input Processing Decimating DLPF Aperture Corrector Slicer RADIO Carrier Control Timing Control Decode Data Pream Detect PHY UW Detect Trans Detect Figure 5. Demodulator Block Diagram Oki Semiconductor 7 s MSM7730 MSM7730 s ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ The MSM7730 MSM7730 supports two modes: · 1-Mbps 2-ary FSK · 2-Mbps 4-ary FSK The demodulator offers three possible interfaces to a limiter/discriminator radio. · Analog data slicer (1Mbps only) · Post discriminator 4-bit ADC (offset binary) · Post discriminator 1-bit ADC (provisional) The radio requirements for the demodulator are: 1 Mb: 20 dB S/N from discriminator 10-5 BER (802.11 specifies sensitivity of 10-5 for 80 dBm) 2 Mb: 30 dB S/N from discriminator 10-5 BER (802.11specifies sensitivity of 10-5 for 75 dBm) Discriminator linearity of ±5% required for specified 2-Mbps operation 4-bit discriminator-to-ADC ranging, to cover approximately ±360 KHz Carrier acquisition for analog slicer option within 4 µs, yielding a duty cycle better than 60:40 for a square wave (demodulation provides signal for carrier lock switch once preamble is detected · RSSI threshold decision within 4 µs of antenna switching · 3-state ADC output during transmit (bus is shared with TxDAC) · · · · · PHY Interface The PHY section of the MSM7730 MSM7730 allows the MAC layers from two different stations to be interconnected via a 2.4-GHz radio signal. Figure 6 shows a block diagram of the PHY interface. PHY Interface Modulator Physical Layer Convergence MAC Demodulator RADIO Radio Control Modem Interface Figure 6. MSM7730 MSM7730 Physical Layer Block Diagram The PHY provides a slow Frequency Hopping Spread Spectrum (FHSS) radio link at either 1 or 2 Mbps. FH is performed over a subset of 1-MHz wide channels with a frequency band of 2.400 to 2.497 GHz. The MSM7730 MSM7730 is not directly in control of the hopping sequence, but rather provides for reprogramming of the radio channel so that this function can be managed under software control. The mapping of data between the MAC and the radio link is called the Physical Layer Convergence Protocol (PLCP). This mapping involves the addition and removal of preamble and header information, as well as the whitening and dewhitening of packet data. Figure 7 shows a block diagram of the PLCP. 8 Oki Semiconductor ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ s MSM7730 MSM7730 s Preamble Formatting Scrambler Data Whitener MOD PHY State Machine DEMOD Header CRC Check De-scrambler De-whitener Add arrows Figure 7. Physical Layer Convergence Protocol Block Diagram Each frame starts with an 80-bit synchronization sequence or preamble, followed by a 16-bit unique word or start of frame deliminiter (SFD). The Physical Data Unit (PDU) is a data-whitened version of the MAC data at either 1 or 2 Mbps. The preamble and header are always transmitted at 1 Mbps. The PDU can be transmitted at either 1 or 2 Mbps. The PHY is required to perform CCA to determine when to transmit, and for the MAC to control the contention back-off timer. PCMCIA Interface The MSM7730 MSM7730 provides a PCMCIA host interface mode designed to permit implementation of PC cards for use with host computers compatible with the PCMCIA PC card standard (Revision 2.1). The interface supports 16-bit transfers to maximize overall system throughput. In addition, common memory may be used to access all control registers. This is useful for low-cost card implementations that do not have a local processor. The MSM7730 MSM7730 uses attribute memory to configure the device and card. The device decodes the least-significant 9-bits of PC card address space, allowing for an attribute memory size of 512 bytes located at addresses 0x000 - 0x1FF. The attribute memory stores the PCMCIA registers as well as the card information structure (CIS) table data. The PCMCIA standard defines four configuration registers. However, only the Configuration Option and the Configuration and Status registers are supported, not the Pin Replacement and Socket and Copy registers. The CIS information data is stored in an off-chip serial EEPROM. When the MSM7730 MSM7730 is reset, the contents of the EEPROM are downloaded to shared RAM. Then the information is mapped to attribute memory space. Oki Semiconductor 9 s MSM7730 MSM7730 s ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 RA15 RA16 DIAG6 DIAG5 DIAG4 DIAG3 DIAG2 DIAG1 DIAG0 RXD VSSO VDDO IFD5 IFD4/SLICE IFD3 IFD2 IFD1 IFD0 RSSITN ANT RADPWR TXC2 TXC1 RXC1 LKDET SYNLEN EECS SYNDAT/EEDIO SYNCLK/EESK DACEN RCK VSSO VDDO PST0 PST1 PST2 PIN CONFIGURATION 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 RD13 RD14 RD15 HIOIS16N HIOIS16N HD10 HD2 HD9 HD1 HD8 HD0 HA0 HA1 HREGN HA2 HPACKN HA3 VDDC VSSC VSSO VDDO HWAITN HA4 HRST HA5 HA6 HA7 HIREQN HWEN HIOWRN HA8 HIORDN HOEN HCE2N HCE1N HD15 HD7 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 RA14 RA13 RA12 RA11 RA10 RA9 RA8 RA7 RA6 RA5 RA4 RA3 RA2 RA1 RA0 SCK VDDO VSSO RWRN RCELN RCEHN RD0 RD1 RD2 RD3 RD4 RD5 RD6 RD7 RD8 RD9 RD10 VDDO VSSO RD11 RD12 Figure 8. 144-Pin Plastic LQFP Pin Assignment 10 Oki Semiconductor PCLK PRESETN PINTN PCLKOUT PUBE PCSN PREAD PREADYN PD17 PD16 PD15 PD14 PD13 PD12 PD11 PD10 PD9 PD8 PD7 PD6 PD5 PD4 VSSO VDDO PD3 PD2 PD1 PD0 HD3 HD11 HD4 HD12 HD5 HD13 HD6 HD14 ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ s MSM7730 MSM7730 s PIN DESCRIPTIONS Host Interface Signal Descriptions (PCI and ISA) Pin Name Direction Description HPACKN Output This signal is asserted when the card is selected and can respond to an I/O read cycle at the address on the address bus. HIOIS16N HIOIS16N Output This signal is asserted whenever the access on A[8:0] corresponds to an I/O location which is capable of a 16bit access. HIOWRN Input Indicates an I/O write cycle. HIORDN Input Indicates an I/O read cycle. HIREQN Output Active low interrupt request and ready/busy indicator prior to I/O card pin replacement. HOEN Input Output enable signal asserted during memory read operations. Assertion of this signal causes memory data to be driven onto HD[15:0]. HREGN Input Assertion of this signal indicates an access to either attribute memory or I/O space. HA[8:0] Input Least significant 9 bits of the PC-card address bus. All other address bits are ignored. HCEN[2:1] Input Active low card enable signals. HCEN[1] selects even numbered bytes. HCEN[2] selects odd numbered bytes. HD[15:0] Bidirectional Bidirectional data bus. Even numbered bytes appear on HD[7:0]. Odd numbered bytes appear on HD[15:8]. HRST Input Active high reset input. HWAITN Output Active low wait output. This signal is asserted if an access is requested that cannot complete immediately. HWEN Input Active low memory write enable input. Indicates a write to either attribute memory or common memory as determined by the state of the HREGN signal. HCE1N Input Assertion of this signal indicates that a DMA transfer is in progress. HCE2N Output Indicates the ISA shared interrupt status. Processor Interface Signal Descriptions (V30HL V30HL, V53A, and 80C186 80C186) Pin Name Direction Description PD[17:0] Bidirectional Bidirectional multiplexed address/data bus driven during the T1 clock state. PD[17:16] are inputs only. PST[2:0] Input Bus status code that indicates the current cycle type. These inputs must be held HIGH when reset is asserted. PCLK/PCLKOUT Input/Output Clock output of the MSM7730 MSM7730 to which all bus interface signals are synchronized. Frequency is 16 MHz during normal operation but is reduced when in hibernate mode. These two pins must be connected together for proper operation. PINTN Output This signal is generated by the host and processor interrupt module. PCSN Input Processor chip select. PREADYN Output Active high ready indication from the MSM7730 MSM7730. PRESETN Output This signal is controlled by the host and is asserted based on the state of the PRSTN bit in the H_CTL register. PUBEN Input Upper byte enable. Indicates that a byte of data is to be transferred on PD[15:8]. PREAD Input Indicates a read cycle when HIGH, and a write cycle when LOW. Oki Semiconductor 11 s MSM7730 MSM7730 s ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ Shared RAM Interface Signal Descriptions Pin Name Direction Description RA[16:0] Output The RAM address is provided by these pins. A maximum address size of 128K words is supported. RD[15:0] Bidirectional The RAM data is provided on these pins. Word or byte operations are supported. When the shared memory is not in use, the data bus is output to prevent a floating data bus consuming power. RCELN Output When asserted, a low byte (or word) shared RAM cycle is active. RCEHN Output When asserted, a high byte (or word) shared RAM cycle is active. RWRN Output When asserted, a write cycle is required. When deasserted a read cycle is required. This signal remains valid before and while RCELN and RCEHN are asserted. EEPROM Interface Signal Descriptions Pin Name Direction Description EEDIO Bidirectional This is a bidirectional data signal for the EEPROM connected directly to data in (DI) of the EEPROM, and to data out (DO) via a resistor (see EEPROM application notes and Figure 2). EECS Output This signal is connected to CS of the EEPROM to provide the chip select. EESK Output This signal is connected to SK of the EEPROM to provide the clock. The clock rate is RCK divided by 64 (250 kHz with RCK at 16 MHz). Radio Interface Signal Descriptions Pin Name Direction Description RXC1 Opencollector/drain Output When asserted reception is enabled, RXC1 is always asserted during reception. This signal is programmable to be open-collector (active low) or open-drain (active high). TXC, TXC2 Opencollector/drain Output When asserted transmission is enabled, both signals are programmable to be open-collector (active low) or open-drain (active high). Transmit is only activated following a receive (where Clear Channel Assessment is performed). The timing of TXC1 and TXC2 at the start of a transmit is programmable from the deassertion of RXC1. RXC2 is typically used for TX Power Amplifier switching, and its assertion depends on the power control mode selected in the MSM7730 MSM7730. RADPWR Opencollector/drain output This pin is asserted to power up the radio circuitry (i.e.,local oscillators) for reception. The pin is programmable to be open-collector (active low) or open-drain (active high). ANT Open-collector output This pin selects one of two antennas for transmission or reception. SLICE Opencollector/drain output This control pin determines the response time constant of an analog data slicer when using the internal modem with an analog data slicer circuit (options MSEL-0 or 1). This pin is programmable to be open-collector (active low) or open-drain (active high). The pin is asserted when CCA has determined a valid IEEE 802.11 GH signal (preamble is detected). SYNCLK, SYNDAT, SYNLEN Open collector LKDET Input These signals provide the interface to the radio synthesizer to select the transmit/receive carrier. Many synthesizers are supported by a flexible architecture. The data is output on SYNDAT ready for the rising edge of SYNCLK. SYNLEN is asserted during the programming, and the data is latched on the rising edge of SYNCLEN. SYNCLK is clocked at RCK divided by 2. SYNCLK and SYNDAT also are used to program a serial DAC used for TX power control, CCA threshold and RSSI measurement (see below). The synthesizer is programmed when the radio is idle. The RSSI and CCA threshold DAC is used at the start of receiving a packet. The TX power DAC is programmed at the start of transmitting packet. The radio provides indication of being in lock with LKDET. This input is active high or low (programmable), pulse sensitive, and latched so that both pulsed and steady out-of-lock signals are recognized. Glitches shorter than 2 RCK periods are ignored. Transmission is prevented when the synthesizer is out-of-lock 12 Oki Semiconductor ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ s MSM7730 MSM7730 s Radio Interface Signal Descriptions (Continued) Pin Name Direction Description DACEN Open-collector For TX power control, CCA threshold and RSSI measurement, data also is clocked into a serial DAC (10/12 bit type; e.g., MAX515/MAX539 MAX515/MAX539) using the SYNCLK and SYNDAT lines as described above, except that DACEN is asserted during the programming, and the data is latched on the rising edge of DACEN. RSSITH is an input from a threshold comparison of the analog RSSI signal from the radio with the DAC output. It is high when the received signal exceeds the programmed threshold. This performs two purposes: A minimum threshold of RSSI can be set before enabling the demodulator for CCA to reduce power. Once a valid receive signal is determined (CCA invalid), the RSSI can be measured with the external comparator/DAC and a SAR within the MSM7730 MSM7730. The RSSI measurement is performed for internal and external modem options when CCA is determined. The same DAC can be used for both TX power control, RSSI threshold and RSSI measurement. RSSITN Input RCK Output A clock to the radio is provided on this pin. The clock is derived from SCK when RADPWR is asserted, with fixed division ratio of one or two (selected by post-reset configuration SCK_CONF). RCK is typically 16 MHz for the radio synthesizer reference. RXD Input The function of this pin depends on the state of the MSEL[3:0] field in the PHY_CONFIG register. Modem Interface Signal Descriptions Pin Name Direction Description IFD[5:0] Bidirectional If MSEL = 1 (low cost for 1-Mbps modem), IFD[5:0] are used to drive a 6-bit DAC at 32 MHz to provide the modulated transmit IF signal at 24 MHz. They are set to the DAC mid-value during receive. It is anticipated that a resistor ladder DAC will be used. If MSEL = 2,3, (1/2-Mbps modem), IFD[5:0] are used to drive a 6-bit DAC at 32 MHz to provide the modulated transmit IF signal at 24 MHz. If MSEL = 2 (1/- Mbps modem, normal ADC) a 4-bit ADC (e.g., CA3304 CA3304 type) provides digitized demodulated data at 16 MHz as input to the baseband controller on pins IFD[3:0] during receive. The ADC outputs must only be enabled during receive (e.g. by connecting RXC1 to the ADC output enable pin). If MSEL = 3 (1/2-Mbps modem, delta ADC), a comparator is used to compare the value of the transmit IF DAC output to the receive demodulated signal, performing a tracing delta ADC function. The same 6-bit DAC (but at 16 MHz) is used on IFD[5:0] as during transmit, and the comparator input is connected to the RXD pin. RXD Input When MSEL = 1 (low-cost 1-Mbps modem), the RXD pin is used for baseband data input from a radio which has a built-in analog data slicer. The MSM7730 MSM7730 has a clock recovery circuitry to synchronize to the incoming data. The recovered clock is output on a diagnostic pin for test purposes. When MSEL = 3 (1/2-Mbps modem, delta ADC), the delta comparator is input on this pin. The recovered clock from the demodulator is output on a diagnostic pin for test purposes. DIAG[6:0] Output Various signals are provided on these pins as diagnostic aids. The registers PHY_CTL[DIAG] and DEM_CTL0[DTST] select what signals are provided on these pins. General Signal Descriptions Pin Name Direction Description SCK Input The system clock to the MSM7730 MSM7730 is provided by this pin. The clock must always be active (i.e., when reset is asserted). The WLAN card operates synchronously to this clock. The MSM7730 MSM7730 and radio operate at SCK/2. The internal modem operates at SCK (32 MHz). The processor operates from a division of SCK (divide by 1 to divide by 8) depending on a register (GLOB_CTL, see Programmers Reference) in the MSM7730 MSM7730. This signal is output as PCK. VSSC Ground These pins serve as ground for the core logic. VSSO Power This pin serves as ground for the I/O pads. VDDC Power This pin serves as power to the core at 3-V nominal. VDDO Power This pin serves as power to I/O pads and can either be 3 V or 5 V nominal. Oki Semiconductor 13 s MSM7730 MSM7730 s ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ MSM7730 MSM7730 REGISTER MAP The following table lists the registers in the MSM7730 MSM7730. MSM7730 MSM7730 Register Map Byte Offset Register Group Width (bits) Register Name Description 0x00 Configuration 8 Device Configuration Stores serial EEPROM size and sets host interface and processor interface modes. 0x10 PCMCIA 8 Configuration Option Stores interrupt, reset, and configuration index information. 8 Configuration and Status Stores general cycle status information, including interrupts and powerdown. 16 Host Control (H_CTL) Contains ISA reset, host interface and processor interface interrupt information 16 Host Address (H_ADDR) Contains the address in shared memory to be accessed by the H_DATA register. 16 Host Data (H_DATA) Stores host data information. 16 Version Number Contains the MSM7730 MSM7730 version number (0xC3). This register is read-only. 16 Global Control Contains mapping information for baseband control registers and MAC/PHY enables. 16 Processor Interrupt Control Contains host interrupt, processor interrupt, and interrupt enable information. 16 EEPROM Data This register is a buffer that contains data being transferred to and from the EEPROM. 16 EEPROM Address Control Contains EEPROM enable and cycle type information. 16 PHY Configuration Contains Modem and PHY revision information as well as transmit and receive status. The 3-bit MSEL field defines the type of modem operation. 0x12 16 Synthesizer Program Contains the least-significant 16 bits of the 32 bits used for synthesizer programming. This register is used in conjunction with the other SYN register located at 0x14. 0x14 16 Synthesizer Program Contains the most-significant 16 bits of the 32 bit s used for synthesizer programming. This register is used in conjunction with the other SYN register located at 0x12. 0x16 16 Radio Control (RAD_CTL) Contains radio configuration and transmit and receive status information. 0x18 16 Radio Delay (RAD_DLYS) Contains programmable delay parameters between the TXC[1:0] and RXC1 signals. 0x1A 16 Radio Power (RAD_PWR) Determines when the TXC2 signal is asserted if the power control word is selected. Two control bits in the PHY control word of a transmit packet determine which one of four 8-bit values is used. This register is used in conjunction with the other PAD_PWR register located at 0x1C. 0x1C 16 Radio Power (RAD_PWR) Determines when the TXC2 signal is asserted if the power control word is selected. Two control bits in the PHY control word of a transmit packet determine which one of four 8-bit values is used. This register is used in conjunction with the other PAD_PWR register located at 0x1A. 0x12 0x00 ISA Host 0x02 0x04 0x00 0x02 Global Control 0x08 0x0C EEPROM 0x0E 0x10 14 PHY/Radio Oki Semiconductor ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ s MSM7730 MSM7730 s MSM7730 MSM7730 Register Map (Continued) Byte Offset 0x1E Register Group Register Name Description 16 RSSIAB Contains two 6-bit fields: RSSIA and RSSIB. RSSIA is set to correspond to 65 dB T the radio input. RSSIB is set to correspond to -85 dB T the radio input. 0x20 16 PHY Control (PHY_CTL) Contains PHY transmit, receive, and Clear Channel Assessment (CCA) status. 0x22 16 User I/O port (internal) The internal port is selected when the MSEL field in the PHY Configuration registers equals a value between 0 and 3. The bit descriptions are different depending on whether this registers is configured for internal or external use (see next register entry). In the internal mode, the two 6-bit fields configure each bit of the user I/O port as input or output, and whether values can be read from or written to this register. 16 User I/O Port (external) The external port is selected when the MSEL field in the PHY Configuration registers equals a value between 4 and 7. The bit descriptions are different depending on whether this registers is configured for internal or external use (see above register entry). One 6-bit field contains the number of clock periods from TXDRDY or RXDRDY assertion. The other 6-bit field contains the number of RXCLK periods from the length field to the start of the PDU packet. 0x26 16 RSSICD Contains two 6-bit fields: RSSIC and RSSID. RSSIC corresponds to -80 dBm at the radio input. RSSID corresponds to -75 dBm at the radio input. 0x28 16 Modem Control 0 Contains two 6-bit fields that set the 1- and 2-Mbps inner symbol modulation index. 0x2A 16 Modem Control 1 Contains settings for parameters such as integration time for slow carrier tracking group, antenna scan delay, ramp-up, and ramp-down sequences. 0x2C 16 Demodulator Control 0 Contains demodulator control word settings. 0x2E 16 Demodulator Control 1 Contains noise threshold and jamming counter information. 0x30 Modem Width (bits) MAC Controll 16 Version Number Contains the MSM7730 MSM7730 MAC version number (0x83). 0x32 16 Buffer Control Contains the size and address of the receive circular buffer in shared memory. 0x34 16 Rx In Pointer Contains a word offset from the start of the receive circular buffer in shared memory. The offset indicates the location of the address where the next word to be received will be stored. 0x36 16 Rx Out Pointer Contains a word offset from the start of the receive circular buffer in shared memory. The offset indicates the first word in the buffer that is available for use by MAC hardware. 0x40 16 Power Down Control Contains Hibernate mode request and wakeup information. 0x44 16 MAC Control Contains filtering mode parameters as well as transmit, receive, PHY, and modem enable information. 0x46 16 Tx Pointer Contains the word offset from the start of the transmit pointer table. 0x48 16 Interrupt Enable Enables interrupts based on the event type. 0x4A 16 Interrupt Acknowledge This register has the exact same format as the Interrupt Enable register. Setting a bit in this registers clears the corresponding bit in the Interrupt Enable register. 0x4C 16 Interrupt Status This register has the exact same format as the Interrupt Enable register but is read-only. This register is written by hardware. 0x4E 16 Sequencer Status Indicates current sequencer activity. Most bits are written by hardware and are read-only. However, a global clear bit allows for all of the read-only bits to be cleared at the same time. Oki Semiconductor 15 s MSM7730 MSM7730 s ­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­ MSM7730 MSM7730 Register Map (Continued) Byte Offset 0x50 Register Group Register Name Description 16 TSF Timer This register works in conjunction with the register at address 0x52 to construct a 32-bit microsecond timer used for time stamps in received frames and beacon transmissions. 0x52 16 TSF Timer This register works in conjunction with the register at address 0x50 to construct a 32-bit microsecond timer used for time stamps in received frames and beacon transmissions. 0x58 16 TSF Comparator 1 This register contains the least-significant 16 bits of a 24-bit TSF timer value. This register works in conjunction with the register at address 0x5A. The 16 bits of the TSF Comparator 1 register and the 8-bits of the TSF Comparator 2 register comprise the 24-bit TSF comparator value. 0x5A 16 TSF Comparator 2 This register contains the most-significant 8 bits of a 24-bit TSF timer value. This register works in conjunction with the register at address 0x58. The 16 bits of the TSF Comparator 1 register and the 8-bits of the TSF Comparator 2 register comprise the 24-bit TSF comparator value. This 8-bit value is contained in the lower 8 bits of this register. The upper 8 bits are reserved. 0x60 16 Add TSF Time Hardware uses the lower 10 bits of this register to determine the length of time that the TSF timer is disabled. This value can be modified by software. 0x64 16 NAV Timer This 16-bit register contains a 1-µs resolution timer that maintains the virtual carrier sense mechanism. The timer is automatically loaded by the MAC but can be modified by software. 0x66 16 Backoff Timer This register is loaded automatically by the MAC from transmit frame header structures. If a backoff condition occurs, the counter begins decrementing until it reaches zero. 0x68 16 Response Timer Contains a timeout value, in increments of 32 µs, after which the MAC aborts the transmit frame if it does not receive an acknowledgment. 0x6A 16 Tick Timer Sets the interval time in milliseconds at which interrupts are generated. 0x6C 16 Timer Control Contains enable and status information for each of the timers in the MAC control register group. 0x6E 16 Slot Time Contains the value used to determine the length of slots required for random backoff. 16 MAC Control Width (bits) Oki Semiconductor The information contained herein can change without notice owing to product and/or technical improvements. Please make sure before using the product that the information you are referring to is up-to-date. The outline of action and examples of application circuits described herein have been chosen as an explanation of the standard action and performance of the product. When you actually plan to use the product, please ensure that the outside conditions are reflected in the actual circuit and assembly designs. Oki assumes no responsibility or liability whatsoever for any failure or unusual or unexpected operation resulting from misuse, neglect, improper installation, repair, alteration or accident, improper handling, or unusual physical or electrical stress including, but not limited to, exposure to parameters outside the specified maximum ratings or operation outside the specified operating range. Neither indemnity against nor license of a third party's industrial and intellectual property right,etc.is granted by us in connection with the use of product and/or the information and drawings contained herein. No responsibility is assumed by us for any infringement of a third party's right which may result from the use thereof. When designing your product, please use our product below the specified maximum ratings and within the specified operating ranges, including but not limited to operating voltage, power dissipation, and operating temperature. The products listed in this document are intended for use in general electronics equipment for commercial applications (e.g.,office automation, communication equipment, measurement equipment, consumer electronics, etc.).These products are not authorized for use in any system or application that requires special or enhanced quality and reliability characteristics nor in any system or application where the failure of such system or application may result in the loss or damage of property or death or injury to humans. Such applications include, but are not limited to: traffic control, automotive, safety, aerospace, nuclear power control, and medical, including life support and maintenance. Certain parts in this document may need governmental approval before they can be exported to certain countries. The purchaser assumes the responsibility of determining the legality of export of these parts and will take appropriate and necessary steps, at their own expense, for export to another country. Copyright 1998 Oki Semiconductor Oki Semiconductor reserves the right to make changes in specifications at anytime and without notice. This information furnished by Oki Semiconductor in this publication is believed to be accurate and reliable. However, no responsibility is assumed by Oki Semiconductor for its use; nor for any infringements of patents or other rights of third parties resulting from its use. No license is granted under any patents or patent rights of Oki. Oki Semiconductor Oki REGIONAL SALES OFFICES Northwest Area South Central Area 785 N. Mary Avenue Sunnyvale, CA 94086 Tel: 408/720-8940 Fax: 408/720-8965 2007 N. Collins Blvd. Suite 303 Richardson, TX 75080 Tel: 972/690-6868 Fax: 972/690-8233 Southwest Area North East Area 2302 Martin Street Suite 250 Irvine, CA 92715 Tel: 714/752-1843 Fax: 714/752-2423 138 River Road Shattuck Office Center Andover, MA 01810 Tel: 978/688-8687 Fax: 978/688-8896 North Central Area Southeast Area 17177 N. Laurel Park Drive Suite 433 Livonia, MI 48152 Tel: 313/464-7200 Fax: 313/464-1724 1590 Adamson Parkway Suite 220 Morrow, GA 30260 Tel: 770/960-9660 Fax: 770/960-9682 Oki WebSite: http://www.okisemi.com Oki FaxBack Service: Call toll free 1-800-OKI-6994 1-800-OKI-6994 Oki Stock No: 320027-001 Corporate Headquarters 785 N. Mary Avenue Sunnyvale, CA 94086-2909 Tel: 408/720-1900 Fax: 408/720-1918