SS2-MGG200-0100 MGG18 MGG19 G3451 MGG14C SUS304 SCS13 SS400 SUS316L MGA12W - Datasheet Archive

 

MagneW 3000 PLUS Smart Electromagnetic Flowmeter Detector (General, FM/CSA Nonincendive Approval) Model MGG18, MGG19 OVERVIEW The

 

No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) MagneW 3000 PLUS Smart Electromagnetic Flowmeter Detector (General, FM/CSA Nonincendive Approval) Model MGG18 MGG18, MGG19 MGG19 OVERVIEW The MagneW 3000 PLUS electromagnetic flowmeter detector is a high performance, highly reliable flowmeter developed with Yamatake's proven MagneW 3000 flow measurement technologies. Model MGG18 MGG18 (watertight model) and model MGG19 MGG19 (submersible model) offer superior process flowrate measurement and couple with a wide range of MagneW 3000 PLUS converters. FEATURES High performance lining · A new, exclusive high quality lining technology and a special mirror-finish PFA lining offers higher anti-adhesive properties than existing models. · The mirror-finish PFA lining is particularly applicable for measurement of sticky pulp and gypsum slurries. · Only pure white PFA with no additives is used to make new linings. · The successful embedded punch plate that offers proven performance under conditions such as rapid thermal change and negative pressure. PFA linings with diameter ranges from 2.5 mm to 600 mm (0.1 to 24 inches) are available, making selection of the best lining easy for a wide variety of applications. Size 2.5 to 600 mm (0.1 to 24 inches) Replacement interfacing detector (optional) · This detector can replace the detector interfaces of our existing models and those of other manufacturers. Please consult your Yamatake representative for details. Rugged detector structure · A stainless steel case has been adopted for sizes of 2.5 mm to 200 mm (0.1 to 8 inches). · A watertight structure effective for environments where moisture and condensation tends to occur is used for the water-tight model (model MGG18 MGG18). · Sizes of 65 and 125 mm (2½ and 5 inches) have been added to our existing product lineup. A wide variety of piping connections Compatibility · A hose or union joint or clamp can be selected for very small size models (diameters of 2.5 to 15 mm (0.1 to 1/2 inches). · A flange structure is available for all sizes (sizes of 2.5 to 1100 mm (0.1 to 44 inches). · A wafer construction can be also selected (sizes of 2.5 to 200 mm (0.1 to 8 inches). Type of protection Specifications are subject to change without notice. Size 700 to 1100 mm (28 to 44 inches) · Remote model converters can be used in combination with our conventional converters. Please consult your Yamatake representative for details. · Model MGG 18/19 are suitable for use in FM/CSA Nonincendive Class I, Division 2, Groups A, B, C and D; Class II, Division 2, Groups F and G; Class III, Division 2. -1- First issue: Feb. 1997 Rev.7: Jun. 2003 No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Yamatake Corporation APPLICATIONS FUNCTIONAL SPECIFICATIONS Pulp and paper Type of protection Pulp liquids, chemicals, corrosive liquids, industrial water, wastewater, etc. Model MGG18 MGG18 JIS C 0920 watertight model NEMA TYPE4X, IEC IP67 Petroleum/petrochemical/chemicals Corrosive liquids, dyestuffs, chemicals, industrial water, waste water, etc. Model MGG19 MGG19 JIS C 0920 submersible model NEMA TYPE6P, IEC IP68 Public utilities Water supply systems, sewage systems, community drainage, human waste, sludge, sediment slurry, regulation of total effluent, etc. FM approval for both Nonincendive for Class I, Division 2, Groups A, B, C and D Suitable for Class II, Division 2, Groups F and G Suitable for Class III, Division 2, indoor and outdoor (type 4X) hazardous locations. Food Potable water, light, medium and high density fluids, industrial water, waste water, etc. CSA approval for both Nonincendive for Class I, Division 2, Groups A, B, C, and D For Class II, Division 2, Groups E, F and G For Class III for used with non-flammable process fluids. Steel/nonferrous metals/ceramics Aluminum slurry, cooling water, industrial water, corrosive liquids, wastewater, etc. Machinery/equipment/electric machinery Corrosive liquids, cooking water, circulating water, industrial water, wastewater, etc. Line size Construction Sediment slurry etc. 2.5, 5, 10, 15, 25, 40, 50, 65, 80, 100, 125, 150, 200, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100 mm (0.1, 0.2, 3/8, 1/2, 1, 1½, 2, 2½, 3, 4, 5, 6, 8, 10, 12, 14, 16, 18, 20, 24, 28, 32, 36, 40, 44 inches) Electric power Flange rating Corrosive liquids, cooling water, industrial water, wastewater, etc. JIS 10K, JIS 16K, JIS 20K, JIS 30K, JPI 150, JPI 300, ANSI 150, ANSI 300, DIN PN10, DIN PN16, DIN PN25, DIN PN40 (Size 2.5 to 50 mm (0.1 to 2 inches) JIS 10K, JIS 16K, JIS 20K, JIS 30K, JIS G3451 G3451 F12 JPI 150, JPI 300,ANSI 150, ANSI 300, DIN PN10, DIN PN16, DIN PN25, DIN PN40 (Size 80 to 200 mm (3 to 8 inches) JIS 10K, JIS 16K, JIS 20K, JIS G3451 G3451 F12 JPI 150, JPI 300, ANSI 150, ANSI 300, DIN PN10, DIN PN16, DIN PN25 (Size 250 to 600 mm (10 to 24 inches), PFA/ETFE lining) JIS 10K, JIS G3451 G3451 F12, JPI 150, ANSI 150, DIN PN10 (Size 250 to 600 mm (10 to 24 inches), chloroprene rubber lining) Building material slurry, sediment slurry, cement slurry, industrial water, etc. Shipbuilding Gas Circulating water for air conditioning, etc. -2- Yamatake Corporation No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Measurement flow range Refer to the minimum/maximum set ranges shown in the table below Minimum flow velocity range is 0 to 0.1 m/s (0 to 0.33 ft/s) Minimum range Size mm inch 2.5 5 10 15 25 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 700 800 900 1000 1100 0.1 0.2 3/8 1/2 1 1½ 2 2½ 3 4 5 6 8 10 12 14 16 18 20 24 28 32 36 40 44 Maximum flow velocity range is 0 to 10 m/s (0 to 32.8 ft/s) Maximum range m3/h 0 to 0.001768 0 to 0.007069 0 to 0.02825 0 to 0.06362 0 to 0.1768 0 to 0.4524 0 to 0.7069 0 to 1.195 0 to 1.810 0 to 2.828 0 to 4.418 0 to 6.362 0 to 11.31 0 to 17.68 0 to 25.45 0 to 34.64 0 to 45.24 0 to 57.26 0 to 70.69 0 to 101.8 0 to 138.6 0 to 181.0 0 to 229.1 0 to 282.8 0 to 342.2 GPM 0 to 0.007782 0 to 0.03113 0 to 0.1246 0 to 0.2802 0 to 0.7782 0 to 1.993 0 to 3.113 0 to 5.261 0 to 7.969 0 to 12.46 0 to 19.46 0 to 28.02 0 to 49.81 0 to 77.82 0 to 112.1 0 to 152.6 0 to 199.3 0 to 252.2 0 to 311.3 0 to 448.3 0 to 610.1 0 to 796.9 0 to 1009 0 to 1246 0 to 1507 Flow conversion Velocity V(m/s) = K × Q m3/h 0 to 0.1767 0 to 0.7068 0 to 2.827 0 to 6.361 0 to 17.67 0 to 45.23 0 to 70.68 0 to 119.4 0 to 180.9 0 to 282.7 0 to 441.7 0 to636.1 0 to 1130 0 to 1767 0 to 2544 0 to 3463 0 to 4523 0 to 5725 0 to 7068 0 to 10178 0 to 13854 0 to 18095 0 to 22902 0 to 28274 0 to 34211 Conversion factor K GPM 0 to 0.7781 0 to 3.112 0 to 12.45 0 to 28.01 0 to 77.81 0 to 199.2 0 to 311.2 0 to 526.0 0 to 796.8 0 to 1245 0 to 1945 0 to 2801 0 to 4980 0 to 7781 0 to 11205 0 to 15251 0 to 19920 0 to 25211 0 to 31125 0 to 44820 0 to 61005 0 to 79680 0 to 100846 0 to 124501 0 to 150646 56.59 14.15 3.537 1.572 0.5659 0.2210 0.1415 0.08371 0.05526 0.03537 0.02264 0.01572 0.008842 0.005659 0.003930 0.002887 0.002210 0.001747 0.001415 0.0009824 0.0007218 0.0005526 0.0004366 0.0003537 0.0002923 1 4K = Flow conversion factor = - × -2 3600 D 3 Q = Flow rate (m /h) Temperature range and pressure range of process fluid Size 2.5 to 10 mm (0.1 to 3/8 inch) Size 250 to 1100 mm (10 to 44 inches) 2.94 MPa (426 psi) 1.96 MPa (284 psi) 1.96 MPa (284 psi) 0.098 MPa (142 psi) -0.098 MPa (-14.2 psi)-40 -10 (-40) (14) -0.098 MPa (-14.2 psi) -40 (-40) 70 100 120 C (158) (212) (248 F) 80 100 C (176) (212 F) Chloroprene rubber and PFA / ETFE lining Polyurethane rubber and PFA / ETFE lining Size 15 to 200 mm (1/2 to 8 inches) 2.94 MPa (426 psi) PFA/ETFE lining PFA lining 0.098 MPa (142 psi) -0.098 MPa (-14.2 psi) -40 (-40) PFA lining (Remote model only) Special products 50 (122) 80 (176) 120 (248) 160 C (320 F) -3- No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Yamatake Corporation PERFORMANCE SPECIFICATIONS Ambient temperature limits -25 to +60°C (-13 to +140°F) (integral model) -30 to +80°C (-22 to +176°F) (remote model, PFA lining) 30 to +60°C (-22 to +140°F) (remote model, polyurethane rubber lining/chloroprene rubber lining) Ambient humidity limits Accuracy (in combination with the model MGG14C MGG14C converter) Vs = Velocity of setting range Vs (m/s) 5 to 100% RH Measurable electrical conductivity Velocity during measurement > Vs × 40% Velocity during measurement < Vs × 40% 1.0 < Vs < 10 ±0.5% of rate ±0.2% of Vs ±(0.1/Vs+0.4)% of ±0.4(0.1/Vs+0.4)% 0.1 < Vs < 1.0 rate of Vs Combined with model MGG14C MGG14C converter 3 µS/cm or more Optional specifications Vs = Velocity of setting range Test report Calibration certificate, withstand voltage test, insulation resistant, hydrostatic pressure test, physical inspection are included. Vs (m/s) Velocity during measurement > Vs × 20% Velocity during measurement < Vs × 20% 1.0 < Vs < 10 ±0.5% of rate ±0.1% of Vs ±(0.1/Vs+0.4)% of ±0.2 (0.1/Vs+0.4)% 0.1 < Vs < 1.0 rate of Vs Traceability certificate The following three documents are included. · Traceability System Chart · Traceability Certificate · Test Report Vs = Velocity of setting range Material certificate Material certificate for electrode/grounding ring Vs (m/s) Gasket for plastic piping When the detector is being mounted on plastic pipe, attach this gasket between the lining and the grounding ring, and between the grounding ring and the plastic pipe flange. Velocity during measurement > Vs × 50% Velocity during measurement < Vs × 50% 1.0 < Vs < 10 ±1.0% of rate ±0.5% of Vs ±(0.2/Vs+0.8)% of 0.1 < Vs < 1.0 (0.1/Vs+0.4)% of Vs rate Attaching the tag number to the terminal box Stamp the tag with the specified number and attach to the terminal box. The maximum number of characters of the tag number is 8. Attaching the tag number to the neck section Stamp the tag with the specified number and attach to the neck section of the detector with stainless wire. The maximum number of characters of the tag number is 16. PHYSICAL SPECIFICATIONS Main body material Measuring pipe materials SUS304 SUS304 stainless steel Flange SUS304 SUS304 stainless steel (size 2.5 to 65 mm (0.1 to 2½ inches) Carbon steel + corrosion-preventive coating (size 80 to 600 mm (3 to 24 inches) Case SCS13 SCS13 stainless steel (size 2.5 to 15 mm (0.1 to 1/2 inch) SUS304 SUS304 stainless steel (size 25 to 200 mm (1 to 8 inches) SS400 SS400 carbon steel (size 250 to 1100 mm (10 to 44 inches) Terminal box Aluminum alloy (remote model) -4- Yamatake Corporation No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) INSTALLATION Finish Model MGG18 MGG18 Electrical connection Standard Terminal box Baked acryl paint Case (size 250 to 1100 mm (10 to 44 inches) Polyurethane paint Integral model Connected to converter Remote model General model G1/2 (PF1/2) internal thread, CM20 internal thread, Pg 13.5 internal thread. FM/CSA Nonincendive model 1/2NPT internal thread for model MGG18 MGG18 Watertight gland for model MGG19 MGG19 Corrosion-resistant Terminal box Baked acryl paint Case (size 250 to 1100 mm (10 to 44 inches) Polyurethane paint Pipe connection Corrosion-proof Terminal box Baked epoxy paint Case (size 250 to 1100 mm (10 to 44 inches) Epoxy paint Wafer (size 2.5 to 200 mm (0.1 to 8 inches) Flange (size 2.5 to 1100 mm (0.1 to 44 inches) Union (size 2.5 to 15 mm (0.1 to 1/2 inch) Hose (size 2.5 to 15 mm (0.1 to 1/2 inch) IDF Clamp (size 2.5 to 15 mm (0.1 to 1/2 inch) Tri Clamp (size 2.5 to 15 mm (0.1 to 1/2 inch) Color Light beige (Munsell 4Y7.2/1.3) Nuts and bolts (for wafer models) S20C carbon steel, SUS304 SUS304 stainless steel Model MGG19 MGG19 Terminal box and case Corrosion-proof tar epoxy paint, black Grounding Resistance less than 100 Process wetted material Length of straight pipe Lining PFA (size 2.5 to 600 mm (0.1 to 24 inches) ETFE (size 80 to 600 mm (3 to 24 inches) Polyurethane rubber (size 25 to 200 mm (1 to 8 inches) Chloroprene rubber (size 250 to 1100 mm (10 to 44 inches) Upstream side A minimum five straight pipe diameters A minimum 10 straight pipe diameters is required if a diffuser/valve/pump is installed upstream side. Downstream side Two straight pipe diameters is recommended. Electrode SUS316L SUS316L, Hastelloy C, titanium, zirconium, tantalum, tungsten-carbide, platinum/iridium Cable (between remote detector and converter) Maximum length 300 m (984 ft) (depends on fluid conductivity) Outer diameter 10 to 12 mm (0.4 to 0.47 inch) Signal cable Dedicated cable: MGA12W MGA12W (O.D. 11.4 mm, 0.75 mm2) or equivalent (CVVS, CEEV etc.) Excitation cable Dedicated cable: MGA12W MGA12W (O.D. 10.5 mm, 2 mm2) or equivalent (CVV and others) Grounding ring SUS316 SUS316, Hastelloy C, titanium, zirconium, tantalum, platinum Union joint SUS316 SUS316 (size 2.5 to 15mm (0.1 to 1/2 inch) Hose SUS316 SUS316 (size 2.5 to 15mm (0.1 to 1/2 inch) IDF Clamp SUS316 SUS316 (size 2.5 to 15mm (0.1 to 1/2 inch) Tri Clamp SUS316 SUS316 (size 2.5 to 15mm (0.1 to 1/2 inch) Gasket PTFE (if the grounding ring is not made of SUS316 SUS316) O-ring Viton rubber (with union joints) -5- No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Yamatake Corporation For FM/CSA Nonincendive model (Remote type) This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D, Class II, Division 2, Groups F and G; Class III, Division 2. Detector Converter SA Exciting coil A A C C CAUTION B B Electrodes Electrodes Power supply and internal voltage of ordinary equipment to the earth shall not exceed 250 V AC 50/ 60Hz, 250 V DC in case of normal /fault conditions. SB X Non-hazardous or division 2 location Detector Shield X Y (Integral type) Power supply Y Non-hazardous or division 2 location Configuration #1 - Preferred for 2.5 mm to 10 mm detectors to minimize noise Converter A Signal processing circuit C Power supply B X Y Excitation circuit Non-hazardous or division 2 location A C B Power supply X Y Non-hazardous or division 2 location Configuration #2 Non-hazardous or division 2 location A C B X Y Non-hazardous or division 2 location Configuration #3 -6- A C B Power supply X Y Non-hazardous or division 2 location Yamatake Corporation No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) MODEL SELECTION Contents of model number table Detector (General model) Structure / Basic model no. Lining Watertight model MGG18U MGG18U PFA Watertight model MGG18D MGG18D PFA Watertight model MGG18D MGG18D Watertight model MGG18F MGG18F Pipe connection Size Union / Hose / Clamp 2.5 to 15 mm (0.1 to 1/2 inch) (0.1 to 3/8 inch) Ref. page page 8 Wafer 2.5 to 10 mm page 9 PFA / ETFE Wafer 15 to 200 mm (1/2 to 8 inches) page 10 PFA / ETFE Flange 15 to 200 mm (1/2 to 8 inches) page 11 Watertight model MGG18F MGG18F PFA / ETFE Flange 250 to 600 mm (10 to 24 inches) page 12 Watertight model MGG18D MGG18D Polyurethane rubber Wafer 25 to 200 mm (1 to 8 inches) page 13 Watertight model MGG18F MGG18F Polyurethane rubber Flange 25 to 200 mm (1 to 8 inches) page 14 Watertight model MGG18F MGG18F Chloroprene rubber Flange 250 to 600 mm (10 to 24 inches) page 15 Watertight model MGG18F MGG18F Chloroprene rubber Flange 700 to 1100 mm (28 to 44 inches) page 16 Detector (Submersible model) Pipe connection Lining Submersible model MGG19D MGG19D PFA / ETFE Wafer 15 to 200 mm (1/2 to 8 inches) page 17 Submersible model MGG19F MGG19F PFA / ETFE Flange 15 to 200 mm (1/2 to 8 inches) page 18 Submersible model MGG19F MGG19F PFA / ETFE Flange 250 to 600 mm (10 to 24 inches) page 19 Submersible model MGG19D MGG19D Polyurethane rubber Wafer 25 to 200 mm (1 to 8 inches) page 20 Submersible model MGG19F MGG19F Polyurethane rubber Flange 25 to 200 mm (1 to 8 inches) page 21 Note) All MGG19 MGG19 models satisfy FM/CSA Nonincendive approval. PFA / ETFE lining Rubber lining -7- Size Ref. page Structure / Basic model no. No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Yamatake Corporation Union / Hose / Clamp type (2.5 to 15 mm (0.1 to 1/2 inch) PFA lining Model MGG18U MGG18U - I II III IV V VI VII VIII IX - X - Y / Options (some options can be selected per each model) Basic model no. Selections MGG18U MGG18U I IV V VI VII VIII Options X - Line size II III IX Optional selections - 2.5 mm (0.1 inch) 002 5 mm (0.2 inch) 005 10 mm (3/8 inch) 010 15 mm (1/2 inch) 015 Lining PFA P Piping connection Union joint R1/2 (PT1/2) external thread U1 Union joint 1/2NPT external thread U2 Union joint R1/2 (PT1/2) internal thread U3 Union joint 1/2NPT internal thread U4 Hose joint H1 IDF clamp C1 Tri clamp C2 Electrode SUS316L SUS316L L Hastelloy C C Titanium K Zirconium H Tungsten carbide (only for size 10 mm or upper) W Others ! Grounding ring SUS316 SUS316 Electrical connec- Integral type tion / watertight Remote G1/2 internal thread / without watertight gland gland type G1/2 internal thread / with brass (Ni-plated) watertight gland G1/2 internal thread / with plastic watertight gland 1/2NPT internal thread / without watertight gland (Note 1) CM20 internal thread / without watertight gland Pg 13.5 internal thread / without watertight gland G1/2 internal thread / with SUS304 SUS304 watertight gland Face-to-face Standard Installation / wir- Integral type ing direction Remote Upstream side (horizontal / vertical piping mounting) type Downstream side (horizontal / vertical piping mounting) Horizontal piping mounting / left side viewed from upstream Horizontal piping mounting / right side viewed from upstream Calibration Standard Others Finish Standard Corrosion-resistant finish Corrosion-proof finish 1 2 3 4 5 6 7 8 A H A B C D A ! X 1 2 Yamatake version (must be selected) Calibration certificate (sent to ordering location separately) Traceability certificate for detector Material certificate (only for electrodes and ground rings) Attachment of the TAG number to the terminal box for detector (Note 2) Attachment of the TAG number plate to neck section for detector Note) S 1. Must be selected for CSA/FM NI approval 2. Must be selected for Tag no. requirement -8- Y A B C K L Yamatake Corporation No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Wafer type (2.5 to 10 mm (0.1 to 3/8 inch) PFA lining Model MGG18D MGG18D - I II III IV V VI VII VIII IX - X XI - Y / Options (some options can be selected per each model) Basic model no. Selections MGG18D MGG18D I IV V VI VII VIII 2.5 mm (0.1 inch) 002 5 mm (0.2 inch) 005 10 mm (3/8 inch) 010 Lining PFA P Piping connection Wafer JIS 10K 11 Wafer JIS 20K 12 Wafer JIS 30K 13 Wafer JIS 10/20K 10/20K for 10 mm flange 14 Wafer JIS 30K for 10 mm flange 15 Wafer ANSI 150 21 Wafer ANSI 300 22 Wafer DIN PN10 41 Wafer DIN PN16 42 Wafer DIN PN25 43 Wafer DIN PN40 44 Wafer DIN PN10/16/25/40 PN10/16/25/40 for 10 mm flange 45 Wafer JPI 150 61 Wafer JPI 300 62 Electrode SUS316L SUS316L Hastelloy C Titanium Zirconium Tantalum Tungsten carbide (only for size 10 mm) Platinum iridium Others Grounding ring SUS316 SUS316 Hastelloy C Titanium Zirconium Tantalum Platinum iridium Others Electrical connec- Integral type tion / watertight Remote G1/2 internal thread / without watertight gland gland type G1/2 internal thread / with brass (Ni-plated) watertight gland G1/2 internal thread / with plastic watertight gland 1/2NPT internal thread / without watertight gland (Note 1) CM20 internal thread / without watertight gland Pg 13.5 internal thread / without watertight gland G1/2 internal thread / with SUS304 SUS304 watertight gland Face-to-face Standard dimensions Others Installation / wir- Integral type ing direction Remote Upstream side (horizontal / vertical piping mounting) type Downstream side (horizontal / vertical piping mounting) Horizontal piping mounting / left side viewed from upstream Horizontal piping mounting / right side viewed from upstream Calibration Standard Others X Finish XI Bolt / nut Options - Line size II III IX Optional selections - Standard Corrosion-resistant finish Corrosion-proof finish None Carbon steel SUS304 SUS304 L C K H T W P ! S C K H T P ! 1 2 3 4 5 6 7 8 A ! H A B C D A ! X 1 2 X 1 2 Yamatake version (must be selected) Calibration certificate (sent to ordering location separately) Traceability certificate for detector Material certificate (only for electrodes and ground rings) With gasket for plastic piping Attachment of the TAG number to the terminal box for detector (Note 2) Attachment of the TAG number plate to neck section for detector -9- Y A B C J K L Note) 1. Must be selected for CSA/FM NI approval 2. Must be selected for Tag no. requirement No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Yamatake Corporation Wafer type (15 to 200 mm (1/2 to 8 inches) PFA / ETFE lining Model MGG18D MGG18D - I II III IV V VI VII VIII IX - X XI - Y / Options (some options can be selected per each model) Basic model no. Selections MGG18D MGG18D I Line size II Lining III Piping connection IV Electrode V Grounding ring VI Electrical connection / watertight gland VII Face-to-face dimensions Installation / wiring direction VIII Calibration X Finish XI Bolt / nut Options IX Optional selections - - 15 mm (1/2 inch) 015 25 mm (1 inch) 025 40 mm (1½ inches) 040 50 mm (2 inches) 050 65 mm (2½ inches) 065 80 mm (3 inches) 080 100 mm (4 inches) 100 125 mm (5 inches) 125 150 mm (6 inches) 150 200 mm (8 inches) 200 ETFE (Size 80 to 200 mm (3 to 8 inches) E PFA P Wafer JIS 10K Wafer JIS 20K Wafer JIS 30K Wafer ANSI 150 Wafer ANSI 300 Wafer JIS G3451 G3451 F12 (size 80 mm or larger) Wafer DIN PN10 Wafer DIN PN16 Wafer DIN PN25 Wafer DIN PN40 Wafer JPI 150 Wafer JPI 300 SUS316L SUS316L Hastelloy C Titanium Zirconium Tantalum Tungsten carbide Platinum iridium Others SUS316 SUS316 Hastelloy C Titanium Zirconium Tantalum Platinum iridium Others Integral type Remote G1/2 internal thread / without watertight gland type G1/2 internal thread / with brass (Ni-plated) watertight gland G1/2 internal thread / with plastic watertight gland 1/2NPT internal thread / without watertight gland (Note 1) CM20 internal thread / without watertight gland Pg 13.5 internal thread / without watertight gland G1/2 internal thread / with SUS304 SUS304 watertight gland Standard Others Integral type Remote Upstream side (horizontal / vertical piping mounting) type Downstream side (horizontal / vertical piping mounting) Horizontal piping mounting / left side viewed from upstream Horizontal piping mounting / right side viewed from upstream Standard Others Standard Corrosion-resistant finish Corrosion-proof finish None Carbon steel SUS304 SUS304 11 12 13 21 22 31 41 42 43 44 61 62 L C K H T W P ! S C K H T P ! 1 2 3 4 5 6 7 8 A ! H A B C D A ! X 1 2 X 1 2 Yamatake version (must be selected) Calibration certificate (sent to ordering location separately) Traceability certificate for detector Material certificate (only for electrodes and ground rings) With gasket for plastic piping Attachment of the TAG number to the terminal box for detector (Note 2) Attachment of the TAG number plate to neck section for detector - 10 - Y A B C J K L Note) 1. Must be selected for CSA/FM NI approval 2. Must be selected for Tag no. requirement Yamatake Corporation No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Flange type (15 to 200 mm (1/2 to 8 inches) PFA / ETFE lining Model MGG18F MGG18F - I II III IV V VI VII VIII IX X - XI - Y / Options (some options can be selected per each model) Basic model no. Selections MGG18F MGG18F Line size II Lining III Piping connection IV Flange material V Electrode VI Grounding ring VII Electrical connection / watertight gland VIII Face-to-face dimensions IX Installation / wiring direction X Calibration XI Finish Options I Optional selections - - 15 mm (1/2 inch) 015 25 mm (1 inch) 025 40 mm (1½ inches) 040 50 mm (2 inches) 050 65 mm (2½ inches) 065 80 mm (3 inches) 080 100 mm (4 inches) 100 125 mm (5 inches) 125 150 mm (6 inches) 150 200 mm (8 inches) 200 ETFE (Size 80 to 200 mm (3 to 8 inches) E PFA P Flange JIS 10K Flange JIS 20K Flange JIS 30K Flange ANSI 150 Flange ANSI 300 Flange JIS G3451 G3451 F12 (line size 80 mm or larger) Flange DIN PN10 Flange DIN PN16 Flange DIN PN25 Flange DIN PN40 Flange JPI 150 Flange JPI 300 Standard Others SUS316L SUS316L Hastelloy C Titanium Zirconium Tantalum Tungsten carbide Platinum iridium Others SUS316 SUS316 Hastelloy C Titanium Zirconium Tantalum Platinum iridium Others Integral type Remote G1/2 internal thread / without watertight gland type G1/2 internal thread / with brass (Ni-plated) watertight gland G1/2 internal thread / with plastic watertight gland 1/2NPT internal thread / without watertight gland (Note 1) CM20 internal thread / without watertight gland Pg 13.5 internal thread / without watertight gland G1/2 internal thread / with SUS304 SUS304 watertight gland Standard Others Integral type Remote Upstream side (horizontal / vertical piping mounting) type Downstream side (horizontal / vertical piping mounting) Horizontal piping mounting / left side viewed from upstream Horizontal piping mounting / right side viewed from upstream Standard Others J1 J2 J3 A1 A2 G1 D1 D2 D3 D4 P1 P2 1 ! L C K H T W P ! S C K H T P ! 1 2 3 4 5 6 7 8 A ! H A B C D A ! Standard Corrosion-resistant finish Corrosion-proof finish X 1 2 Yamatake version (must be selected) Calibration certificate (sent to ordering location separately) Traceability certificate for detector Material certificate (only for electrodes and ground rings) With gasket for plastic piping Attachment of the TAG number to the terminal box for detector (Note 2) Attachment of the TAG number plate to neck section for detector - 11 - Y A B C J K L Note) 1. Must be selected for CSA/FM NI approval 2. Must be selected for Tag no. requirement No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Yamatake Corporation Flange type (250 to 600 mm (10 to 24 inches) PFA / ETFE lining Model MGG18F MGG18F - I II III IV V VI VII VIII IX X - XI - Y / Options (some options can be selected per each model) Basic model no. Selections MGG18F MGG18F I III IV V VI VII VIII X Options XI - Line size II IX Optional selections - 250 mm (10 inches) 250 300 mm (12 inches) 300 350 mm (14 inches) 350 400 mm (16 inches) 400 450 mm (18 inches) 450 500 mm (20 inches) 500 600 mm (24 inches) 600 Lining ETFE E PFA P Piping connection Flange JIS 10K J1 Flange JIS 20K J2 Flange ANSI 150 A1 Flange ANSI 300 (Size 16 inches or smaller) A2 Flange JIS G3451 G3451 F12 G1 Flange DIN PN10 D1 Flange DIN PN16 D2 Flange DIN PN25 D3 Flange JPI 150 P1 Flange JPI 300 (Size 400 mm or smaller) P2 Flange material Standard 1 Others ! Electrode SUS316L SUS316L Hastelloy C Titanium Zirconium Tantalum Tungsten carbide Platinum iridium Others Grounding ring SUS316 SUS316 Hastelloy C Titanium Others Electrical connec- Integral type tion / watertight Remote G1/2 internal thread / without watertight gland gland type G1/2 internal thread / with brass (Ni-plated) watertight gland G1/2 internal thread / with plastic watertight gland 1/2NPT internal thread / without watertight gland (Note 1) CM20 internal thread / without watertight gland Pg 13.5 internal thread / without watertight gland G1/2 internal thread / with SUS304 SUS304 watertight gland Face-to-face Standard dimensions Others Installation / wir- Integral type ing direction Remote Upstream side (horizontal / vertical piping mounting) type Downstream side (horizontal / vertical piping mounting) Horizontal piping mounting / left side viewed from upstream Horizontal piping mounting / right side viewed from upstream Calibration Standard Others Finish L C K H T W P ! S C K ! 1 2 3 4 5 6 7 8 A ! H A B C D A ! Standard Corrosion-resistant finish Corrosion-proof finish X 1 2 Yamatake version (must be selected) Calibration certificate (sent to ordering location separately) Traceability certificate for detector Material certificate (only for electrodes and ground rings) With gasket for plastic piping Attachment of the TAG number to the terminal box for detector (Note 2) Attachment of the TAG number plate to neck section for detector - 12 - Y A B C J K L Note) 1. Must be selected for CSA/FM NI approval. 2. Must be selected for Tag no. requirement. Yamatake Corporation No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Wafer type (25 to 200 mm (1 to 8 inches) Polyurethane rubber lining Model MGG18D MGG18D - I II III IV V VI VII VIII IX - X XI - Y / Options (some options can be selected per each model) Basic model no. Selections MGG18D MGG18D I IV V VI VII VIII 25 mm (1 inch) 025 40 mm (1½ inches) 040 50 mm (2 inches) 050 65 mm (2½ inches) 065 80 mm (3 inches) 080 100 mm (4 inches) 100 125 mm (5 inches) 125 150 mm (6 inches) 150 200 mm (8 inches) 200 Lining Polyurethane rubber Q Piping connection Wafer JIS 10K 11 Wafer JIS 20K 12 Wafer JIS 30K 13 Wafer ANSI 150 21 Wafer ANSI 300 22 Wafer JIS G3451 G3451 F12 (line size 80 mm or larger) 31 Wafer DIN PN10 41 Wafer DIN PN16 42 Wafer DIN PN25 43 Wafer DIN PN40 44 Wafer JPI 150 61 Wafer JPI 300 62 Electrode SUS316L SUS316L L Titanium K Tungsten carbide (only for size 10 mm) W Others ! Grounding ring SUS316 SUS316 Titanium Others Electrical connec- Integral type tion / watertight Remote G1/2 internal thread / without watertight gland gland type G1/2 internal thread / with brass (Ni-plated) watertight gland G1/2 internal thread / with plastic watertight gland 1/2NPT internal thread / without watertight gland (Note 1) CM20 internal thread / without watertight gland Pg 13.5 internal thread / without watertight gland G1/2 internal thread / with SUS304 SUS304 watertight gland Face-to-face Standard dimensions Installation / wir- Integral type ing direction Remote Upstream side (horizontal / vertical piping mounting) type Downstream side (horizontal / vertical piping mounting) Horizontal piping mounting / left side viewed from upstream Horizontal piping mounting / right side viewed from upstream Calibration Standard Others X Finish XI Bolt / nut Options - Line size II III IX Optional selections - Standard Corrosion-resistant finish Corrosion-proof finish None Carbon steel SUS304 SUS304 S K ! 1 2 3 4 5 6 7 8 A H A B C D A ! X 1 2 X 1 2 Yamatake version (must be selected) Calibration certificate (sent to ordering location separately) Traceability certificate for detector Material certificate (only for electrodes and ground rings) With gasket for plastic piping Attachment of the TAG number to the terminal box for detector (Note 2) Attachment of the TAG number plate to neck section for detector - 13 - Y A B C J K L Note) 1. Must be selected for CSA/FM NI approval 2. Must be selected for Tag no. requirement No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Yamatake Corporation Flange type (25 to 200 mm (1 to 8 inches) Polyurethane rubber lining Model MGG18F MGG18F - I II III IV V VI VII VIII IX X - XI - Y / Options (some options can be selected per each model) Basic model no. Selections MGG18F MGG18F I IV V VI VII VIII X Options XI - Line size II III IX Optional selections - 25 mm (1 inch) 025 40 mm (1½ inches) 040 50 mm (2 inches) 050 65 mm (2½ inches) 065 80 mm (3 inches) 080 100 mm (4 inches) 100 125 mm (5 inches) 125 150 mm (6 inches) 150 200 mm (8 inches) 200 Lining Polyurethane rubber Q Piping connection Flange JIS 10K J1 Flange JIS 20K J2 Flange JIS 30K J3 Flange ANSI 150 A1 Flange ANSI 300 A2 Flange JIS G3451 G3451 F12 (line size 80 mm or larger) G1 Flange DIN PN10 D1 Flange DIN PN16 D2 Flange DIN PN25 D3 Flange DIN PN40 D4 Flange JPI 150 P1 Flange JPI 300 P2 Flange material Standard 1 Others ! Electrode SUS316L SUS316L Titanium Tungsten carbide (only for size 10 mm) Others Grounding ring SUS316 SUS316 Titanium Others Electrical connec- Integral type tion / watertight Remote G1/2 internal thread / without watertight gland gland type G1/2 internal thread / with brass (Ni-plated) watertight gland G1/2 internal thread / with plastic watertight gland 1/2NPT internal thread / without watertight gland (Note 1) CM20 internal thread / without watertight gland Pg 13.5 internal thread / without watertight gland G1/2 internal thread / with SUS304 SUS304 watertight gland Face-to-face Standard dimensions Installation / wir- Integral type ing direction Remote Upstream side (horizontal / vertical piping mounting) type Downstream side (horizontal / vertical piping mounting) Horizontal piping mounting / left side viewed from upstream Horizontal piping mounting / right side viewed from upstream Calibration Standard Others Finish L K W ! S K ! 1 2 3 4 5 6 7 8 A H A B C D A ! Standard Corrosion-resistant finish Corrosion-proof finish X 1 2 Yamatake version (must be selected) Calibration certificate (sent to ordering location separately) Traceability certificate for detector Material certificate (only for electrodes and ground rings) With gasket for plastic piping Attachment of the TAG number to the terminal box for detector (Note 2) Attachment of the TAG number plate to neck section for detector - 14 - Y A B C J K L Note) 1. Must be selected for CSA/FM NI approval 2. Must be selected for Tag no. requirement Yamatake Corporation No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Flange type (250 to 600 mm (10 to 24 inches) Chloroprene rubber lining Model MGG18F MGG18F - I II III IV V VI VII VIII IX X - XI - Y / Options (some options can be selected per each model) Basic model no. Selections MGG18F MGG18F I IV V VI VII VIII X Options XI - Line size II III IX Optional selections - 250 mm (10 inches) 250 300 mm (12 inches) 300 350 mm (14 inches) 350 400 mm (16 inches) 400 450 mm (18 inches) 450 500 mm (20 inches) 500 600 mm (24 inches) 600 Lining Chloroprene rubber R Piping connection Flange JIS 10K J1 Flange ANSI 150 A1 Flange JIS G3451 G3451 F12 G1 Flange DIN PN10 D1 Flange JPI 150 P1 Flange material Standard 1 Others ! Electrode SUS316L SUS316L Titanium Tungsten carbide Others Grounding ring SUS316 SUS316 Titanium Others Electrical connec- Integral type tion / watertight Remote G1/2 internal thread / without watertight gland gland type G1/2 internal thread / with brass (Ni-plated) watertight gland G1/2 internal thread / with plastic watertight gland 1/2NPT internal thread / without watertight gland (Note 1) CM20 internal thread / without watertight gland Pg 13.5 internal thread / without watertight gland G1/2 internal thread / with SUS304 SUS304 watertight gland Face-to-face Standard dimensions Others Installation / wir- Integral type ing direction Remote Upstream side (horizontal / vertical piping mounting) type Downstream side (horizontal / vertical piping mounting) Horizontal piping mounting / left side viewed from upstream Horizontal piping mounting / right side viewed from upstream Calibration Standard Others Finish Standard Corrosion-resistant finish Corrosion-proof finish S K ! 1 2 3 4 5 6 7 8 A ! H A B C D A ! X 1 2 Yamatake version (must be selected) Calibration certificate (sent to ordering location separately) Traceability certificate for detector Material certificate (only for electrodes and ground rings) With gasket for plastic piping Attachment of the TAG number to the terminal box for detector (Note 2) Attachment of the TAG number plate to neck section for detector Note) L K W ! 1. Must be selected for CSA/FM NI approval 2. Must be selected for Tag no. requirement - 15 - Y A B C J K L No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Yamatake Corporation Flange type (700 to 1100 mm (28 to 44 inches) Chloroprene rubber lining Model MGG18F MGG18F - I II III IV V VI VII VIII IX X - XI - Y / Options (some options can be selected per each model) Basic model no. Selections MGG18F MGG18F I Line size Optional selections - - 700 mm (28 inches) 700 800 mm (32 inches) 800 900 mm (36 inches) 900 1000 mm (40 inches) 10H 1100 mm (44 inches) 11H II Lining Chloroprene rubber III Piping connection Flange JIS 10K R J1 Flange ANSI 150 A1 Flange JIS G3451 G3451 F12 Flange material V Electrode D1 Flange JPI 150 IV G1 Flange DIN PN10 P1 Standard 1 SUS316L SUS316L L Titanium K Tungsten carbide VI Grounding ring W Others ! S Others VII SUS316 SUS316 ! Electrical connec- Integral type tion / watertight Remote G1/2 internal thread / without watertight gland gland type G1/2 internal thread / with brass (Ni-plated) watertight gland 1 2 3 G1/2 internal thread / with plastic watertight gland Installation / wiring direction 7 G1/2 internal thread / with SUS304 SUS304 watertight gland IX 6 Pg 13.5 internal thread / without watertight gland Face-to-face dimensions 5 CM20 internal thread / without watertight gland VIII 4 1/2NPT internal thread / without watertight gland 8 Standard A Others ! A Downstream side (horizontal / vertical piping mounting) B C Horizontal piping mounting / right side viewed from upstream Calibration H Upstream side (horizontal / vertical piping mounting) Horizontal piping mounting / left side viewed from upstream X Integral type Remote type D ! Standard X Corrosion-resistant finish 1 Corrosion-proof finish Options Finish A Others XI Standard 2 Yamatake version (must be selected) Y Calibration certificate (sent to ordering location separately) A Traceability certificate for detector B Material certificate (only for electrodes and ground rings) C Attachment of the TAG number to the terminal box for detector (Note 1) K Attachment of the TAG number plate to neck section for detector L Note) 1. Must be selected for Tag no. requirement - 16 - Yamatake Corporation No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Submersible detector with FM/CSA NI approval Wafer type (15 to 200 mm (1/2 to 8 inches) PFA / ETFE lining Model MGG19D MGG19D - I II III IV V VI VII VIII IX - X XI - Y / Options (some options can be selected per each model) Basic model no. Selections MGG19D MGG19D I - Line size II III IV V VI VII VIII IX 15 mm (1/2 inch) 015 25 mm (1 inch) 025 40 mm (1½ inches) 040 50 mm (2 inches) 050 65 mm (2½ inches) 065 80 mm (3 inches) 080 100 mm (4 inches) 100 125 mm (5 inches) 125 150 mm (6 inches) 150 200 mm (8 inches) 200 Lining ETFE (Size 80 to 200 mm (3 to 8 inches) E PFA P Piping connection Wafer JIS 10K 11 Wafer JIS 20K 12 Wafer JIS 30K 13 Wafer ANSI 150 21 Wafer ANSI 300 22 Wafer JIS G3451 G3451 F12 (line size 80 mm or larger) 31 Wafer DIN PN10 41 Wafer DIN PN16 42 Wafer DIN PN25 43 Wafer DIN PN40 44 Wafer JPI 150 61 Wafer JPI 300 62 Electrode SUS316L SUS316L L Hastelloy C C Titanium K Zirconium H Tantalum T Tungsten carbide W Platinum iridium P Others ! Grounding ring SUS316 SUS316 Hastelloy C Titanium Zirconium Tantalum Platinum iridium Others Electrical connection / Remote G1/2 internal thread / with brass (Ni-plated) watertight gland watertight gland type G1/2 internal thread / with SUS304 SUS304 watertight gland Face-to-face dimenStandard sions Others Installation / wiring Remote Upstream side (horizontal / vertical piping mounting) direction type Downstream side (horizontal / vertical piping mounting) Horizontal piping mounting / left side viewed from upstream Horizontal piping mounting / right side viewed from upstream Calibration Standard Others X Finish XI Bolt / nut Options Optional selections - Standard None Carbon steel SUS304 SUS304 3 8 A ! A B C D A ! X X 1 2 Yamatake version (must be selected) Calibration certificate (sent to ordering location separately) Traceability certificate for detector Material certificate (only for electrodes and ground rings) With gasket for plastic piping Attachment of the TAG number to the terminal box for detector (Note 1) Attachment of the TAG number plate to neck section for detector Note) S C K H T P ! 1. Must be selected for Tag no. requirement - 17 - Y A B C J K L No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Yamatake Corporation Submersible detector with FM/CSA NI approval Flange type (15 to 200 mm (1/2 to 8 inches) PFA / ETFE lining Model MGG19F MGG19F - I II III IV V VI VII VIII IX X - XI - Y / Options (some options can be selected per each model) Basic model no. Selections MGG19F MGG19F I - Line size II III IV V VI VII VIII IX X XI Options Optional selections - 15 mm (1/2 inch) 015 25 mm (1 inch) 025 40 mm (1½ inches) 040 50 mm (2 inches) 050 65 mm (2½ inches) 065 80 mm (3 inches) 080 100 mm (4 inches) 100 125 mm (5 inches) 125 150 mm (6 inches) 150 200 mm (8 inches) 200 Lining ETFE (Size 80 to 200 mm (3 to 8 inches) E PFA P Piping connection Flange JIS 10K J1 Flange JIS 20K J2 Flange JIS 30K J3 Flange ANSI 150 A1 Flange ANSI 300 A2 Flange JIS G3451 G3451 F12 (line size 80 mm or larger) G1 Flange DIN PN10 D1 Flange DIN PN16 D2 Flange DIN PN25 D3 Flange DIN PN40 D4 Flange JPI 150 P1 Flange JPI 300 P2 Flange material Standard 1 Others ! Electrode SUS316L SUS316L L Hastelloy C C Titanium K Zirconium H Tantalum T Tungsten carbide W Platinum iridium P Others ! Grounding ring SUS316 SUS316 Hastelloy C Titanium Zirconium Tantalum Platinum iridium Others Electrical connection / Remote G1/2 internal thread / with brass (Ni-plated) watertight gland watertight gland type G1/2 internal thread / with SUS304 SUS304 watertight gland Face-to-face dimensions Standard Others Installation / wiring direc- Remote Upstream side (horizontal / vertical piping mounting) tion type Downstream side (horizontal / vertical piping mounting) Horizontal piping mounting / left side viewed from upstream Horizontal piping mounting / right side viewed from upstream Calibration Standard Others Finish Standard 3 8 A ! A B C D A ! X Yamatake version (must be selected) Calibration certificate (sent to ordering location separately) Traceability certificate for detector Material certificate (only for electrodes and ground rings) With gasket for plastic piping Attachment of the TAG number to the terminal box for detector (Note 1) Attachment of the TAG number plate to neck section for detector Note) S C K H T P ! 1. Must be selected for Tag no. requirement - 18 - Y A B C J K L Yamatake Corporation No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Submersible detector with FM/CSA NI approval Flange type (250 to 600 mm (10 to 24 inches) PFA / ETFE lining Model MGG19F MGG19F - I II III IV V VI VII VIII IX X - XI - Y / Options (some options can be selected per each model) Basic model no. Selections MGG19F MGG19F I III IV V VI VII VIII X Options XI - Line size II IX Optional selections - 250 mm (10 inches) 250 300 mm (12 inches) 300 350 mm (14 inches) 350 400 mm (16 inches) 400 450 mm (18 inches) 450 500 mm (20 inches) 500 600 mm (24 inches) 600 Lining ETFE E PFA P Piping connection Flange JIS 10K J1 Flange JIS 20K J2 Flange ANSI 150 A1 Flange ANSI 300 (Size 16 inches or smaller) A2 Flange JIS G3451 G3451 F12 G1 Flange DIN PN10 D1 Flange DIN PN16 D2 Flange DIN PN25 D3 Flange JPI 150 P1 Flange JPI 300 (Size 400 mm or smaller) P2 Flange material Standard 1 Others ! Electrode SUS316L SUS316L L Hastelloy C C Titanium K Zirconium H Tantalum T Tungsten carbide W Platinum iridium P Others ! Grounding ring SUS316 SUS316 Hastelloy C Titanium Others Electrical connection / Remote G1/2 internal thread / with brass (Ni-plated) watertight gland watertight gland type G1/2 internal thread / with SUS304 SUS304 watertight gland Face-to-face dimensions Standard Others Installation / wiring direc- Remote Upstream side (horizontal / vertical piping mounting) tion type Downstream side (horizontal / vertical piping mounting) Horizontal piping mounting / left side viewed from upstream Horizontal piping mounting / right side viewed from upstream Calibration Standard Others Finish Standard 3 8 A ! A B C D A ! X Yamatake version (must be selected) Calibration certificate (sent to ordering location separately) Traceability certificate for detector Material certificate (only for electrodes and ground rings) With gasket for plastic piping Attachment of the TAG number to the terminal box for detector (Note 1) Attachment of the TAG number plate to neck section for detector Note) S C K ! 1. Must be selected for Tag no. requirement - 19 - Y A B C J K L No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Yamatake Corporation Submersible detector with FM/CSA NI approval Wafer type (25 to 200 mm (1 to 8 inches) Polyurethane rubber lining Model MGG19D MGG19D - I II III IV V VI VII VIII IX - X XI - Y / Options (some options can be selected per each model) Basic model no. Selections MGG19D MGG19D I Line size Optional selections - - 25 mm (1 inch) 025 40 mm (1½ inches) 040 50 mm (2 inches) 050 65 mm (2½ inches) 065 80 mm (3 inches) 080 100 mm (4 inches) 100 125 mm (5 inches) 125 150 mm (6 inches) 150 200 mm (8 inches) 200 II Lining Polyurethane rubber III Piping connection Wafer JIS 10K Q 11 Wafer JIS 20K 12 Wafer JIS 30K 13 Wafer ANSI 150 21 Wafer ANSI 300 22 Wafer JIS G3451 G3451 F12 (line size 80 mm or larger) 31 Wafer DIN PN10 41 Wafer DIN PN16 42 Wafer DIN PN25 43 Wafer DIN PN40 Electrode 61 Wafer JPI 300 IV 44 Wafer JPI 150 62 SUS316L SUS316L L Titanium K Tungsten carbide (only for size 10 mm) V Grounding ring W Others ! SUS316 SUS316 S Titanium K ! Others VI Electrical connection / watertight gland Remote type VII Face-to-face dimensions Standard VIII Installation / wiring direc- Remote tion type G1/2 internal thread / with brass (Ni-plated) watertight gland 3 G1/2 internal thread / with SUS304 SUS304 watertight gland 8 A Upstream side (horizontal / vertical piping mounting) A Downstream side (horizontal / vertical piping mounting) B Horizontal piping mounting / left side viewed from upstream IX Calibration C Horizontal piping mounting / right side viewed from upstream D Standard A Others ! Finish Standard Bolt / nut None X Carbon steel 1 SUS304 SUS304 2 Options X XI X Yamatake version (must be selected) Y Calibration certificate (sent to ordering location separately) A Traceability certificate for detector B Material certificate (only for electrodes and ground rings) C With gasket for plastic piping J Attachment of the TAG number to the terminal box for detector (Note 1) K Attachment of the TAG number plate to neck section for detector L Note) 1. Must be selected for Tag no. requirement - 20 - Yamatake Corporation No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Submersible detector with FM/CSA NI approval Flange type (25 to 200 mm (1 to 8 inches) Polyurethane rubber lining Model MGG19F MGG19F - I II III IV V VI VII VIII IX X - XI - Y / Options (some options can be selected per each model) Basic model no. Selections MGG19F MGG19F I Line size Optional selections - - 25 mm (1 inch) 40 mm (1½ inches) 025 040 50 mm (2 inches) 050 65 mm (2½ inches) 065 80 mm (3 inches) 080 100 mm (4 inches) 100 125 mm (5 inches) 125 150 mm (6 inches) 150 200 mm (8 inches) 200 II Lining Polyurethane rubber III Piping connection Flange JIS 10K Q J1 Flange JIS 20K J2 Flange JIS 30K J3 Flange ANSI 150 A1 Flange ANSI 300 A2 Flange JIS G3451 G3451 F12 (line size 80 mm or larger) G1 Flange DIN PN10 D1 Flange DIN PN16 D2 Flange DIN PN25 D3 Flange DIN PN40 D4 Flange JPI 150 P1 Flange JPI 300 P2 IV Flange material Standard V Electrode SUS316L SUS316L 1 L Titanium K Tungsten carbide VI Grounding ring W Others ! VIII IX S K Others VII SUS316 SUS316 Titanium ! Electrical connection / watertight gland Remote type Face-to-face dimensions Standard Installation / wiring direc- Remote tion type G1/2 internal thread / with brass (Ni-plated) watertight gland 3 G1/2 internal thread / with SUS304 SUS304 watertight gland 8 A Upstream side (horizontal / vertical piping mounting) A C Horizontal piping mounting / right side viewed from upstream D Standard A Others ! XI Finish Options Calibration B Horizontal piping mounting / left side viewed from upstream X Downstream side (horizontal / vertical piping mounting) Standard X Yamatake version (must be selected) Y Calibration certificate (sent to ordering location separately) A Traceability certificate for detector B Material certificate (only for electrodes and ground rings) C With gasket for plastic piping J Attachment of the TAG number to the terminal box for detector (Note 1) K Attachment of the TAG number plate to neck section for detector L Note) 1. Must be selected for Tag no. requirement - 21 - No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Yamatake Corporation DIMENSIONS All dimensions are in millimeters, dimensions in brackets ( ) are in inches (inch). (1.97) Union joint (size 2.5 to 15 mm (0.1 to 1/2 inch) (1.19 max.) (3.31) (3.78) (2.80) (2.83) (7.48) (1.85) (3.31) (3.86) (2.05) (4.33) (3.94) Hose joint (size 2.5 to 15 mm (0.1 to 1/2 inch) (1.19 max.) (3.31) (3.78) (2.80) (2.83) (7.48) (1.85) (3.31) (3.86) (2.05) (4.33) (3.94) - 22 - Yamatake Corporation No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) IDF / Tri clamp (size 2.5 to 15 mm (0.1 to 1/2 inch) (1.19 max.) (3.31) (3.78) (2.80) (2.83) (7.48) (1.85) (3.31) (3.86) (2.05) (4.33) (3.94) Note) 1. An integral detector includes an integral converter instead of a terminal box. 2. Clamp size: 1S - 23 - No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Yamatake Corporation Wafer type (size 2.5 to 15 mm (0.1 to 1/2 inch) (1.19 max.) (3.31) (1.85) (3.31) (2.05) (4.33) Wafer type (size 25 to 200 mm (1 to 8 inches) (1.19 max.) (3.31) (1.85) (3.31) Size mm 2.5 5 10 15 25 40 50 65 80 (inches) (0.1) (0.2) (3/8) (1/2) (1) (1½) (2) (2½) (3) Face to face mm 56 56 56 56 56 80 86 96 106 L dimension (inches) (2.20) (2.20) (2.20) (2.20) (2.20) (3.15) (3.39) (3.78) (4.17) mm 71 71 71 71 77 84 93 100 108 H1 (inches) (2.80) (2.80) (2.80) (2.80) (3.03) (3.31) (3.66) (3.94) (4.25) mm 72 72 72 72 34 43.5 52 62 67 H2 (inches) (2.83) (2.83) (2.83) (2.83) (1.34) (1.71) (2.05) (2.44) (2.64) Height mm 190 190 190 190 158 175 192 209 222 H3 (inches) (7.48) (7.48) (7.48) (7.48) (6.22) (6.89) (7.56) (8.23) (8.74) mm 96 96 96 96 102 109 118 125 133 H4 (inches) (3.78) (3.78) (3.78) (3.78) (4.02) (4.29) (4.65) (4.92) (5.24) mm 98 98 98 98 106 125 135 148 164 Housing width W (inches) (3.86) (3.86) (3.86) (3.86) (4.17) (4.92) (5.31) (5.83) (6.46) Housing outer mm 49.5 49.5 49.5 49.5 68 87 104 124 134 D diameter (inches) (1.95) (1.95) (1.95) (1.95) (2.68) (3.43) (4.09) (4.88) (5.28) kg 2.6 2.6 2.6 2.3 2.6 2.8 3.4 4.5 5.2 Weight (lb) (5.7) (5.7) (5.7) (5.1) (5.7) (6.2) (7.5) (9.9) (11.5) Note) 1. An integral detector includes an integral converter instead of a terminal box. - 24 - 100 (4) 120 (4.72) 121 (4.76) 79.5 (3.13) 247 (9.72) 146 (5.75) 189 (7.44) 159 (6.26) 6.7 (14.8) 125 150 200 (5) (6) (8) 140 160 200 (5.51) (6.30) (7.87) 133 160 185 (5.24) (6.30) (7.28) 95 110 135 (3.74) (4.33) (5.31) 275 317 367 (10.83) (12.48) (14.45) 158 185 210 (6.22) (7.28) (8.27) 214 240 290 (8.43) (9.45) (11.42) 190 220 270 (7.48) (8.66) (10.63) 10.0 13.6 22.0 (22.0) (30.0) (48.5) Yamatake Corporation No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Flange type (size 2.5 to 15 mm (0.1 to 1/2 inch) (1.19 max.) (3.31) (1.85) (3.31) (2.05) (4.33) Flange type (size 25 mm (1 inch) (1.19 max.) (3.31) (1.85) (3.31) Size mm 2.5 5 10 (inches) (0.1) (0.2) (3/8) mm 160 160 160 Face to face dimension L (inches) (6.30) (6.30) (6.30) mm 71 71 71 H1 (inches) (2.80) (2.80) (2.80) mm 72 72 72 H2 (inches) (2.83) (2.83) (2.83) Height mm 190 190 190 H3 (inches) (7.48) (7.48) (7.48) mm 96 96 96 H4 (inches) (3.78) (3.78) (3.78) mm 98 98 98 Width W (inches) (3.86) (3.86) (3.86) kg 5.0 5.0 5.0 Weight (lb) (11.0) (11.0) (11.0) Note) 1. This table is for remote detectors. 2. An integral detector includes an integral converter instead of a terminal box. 3. The table indicates dimensions for ANSI 150 flange. - 25 - 15 25 (1/2) 200 (7.87) 71 (2.80) 72 (2.83) 190 (7.48) 96 (3.78) 98 (3.86) 5.0 (11.0) (1) 200 (7.87) 77 (3.03) 54 (2.13) 178 (7.01) 102 (4.02) 106 (4.17) 6.6 (14.6) No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Yamatake Corporation Flange type (size 40 to 100 mm (1½ to 4 inches) (1.19 max.) (3.31) (1.85) (3.31) Flange type (size 150 to 600 mm (6 to 24 inches) (3.31) (3.31) (1.85) (1.19 max.) Size mm 40 50 65 80 100 125 150 200 250 300 350 400 450 500 600 (inches) (1½) (2) (2½) (3) (4) (5) (6) (8) (10) (12) (14) (16) (18) (20) (24) Face to face mm 200 200 200 200 250 250 300 350 450 500 550 600 600 600 650 L dimension (inches) (7.87) (7.87) (7.87) (7.87) (9.84) (9.84) (11.81) (13.78) (17.72) (19.69) (21.65) (23.62) (23.62) (23.62) (25.59) mm 84 93 100 108 121 133 160 185 235 258 282 310 339 366 415 H1 (inches) (3.31) (3.66) (3.94) (4.25) (4.76) (5.24) (6.30) (7.28) (9.25) (10.16) (11.10) (12.20) (13.35) (14.41) (16.34) mm 77 88 103 113 131 145 174 204 224 271 297 340 364 396 456 H2 (inches) (3.03) (3.46) (4.06) (4.45) (5.16) (5.71) (6.85) (8.03) (8.82) (10.67) (11.09) (13.39) (14.33) (15.59) (17.95) Height mm 208 228 250 268 299 325 381 436 506 576 626 697 750 809 918 H3 (inches) (8.19) (8.98) (9.84) (10.55) (11.77) (12.80) (15.0) (17.17) (19.92) (22.68) (24.65) (27.44) (29.53) (31.85) (36.14) mm 109 118 125 133 146 158 185 210 260 283 307 335 364 391 440 H4 (inches) (4.29) (4.65) (4.92) (5.24) (5.75) (6.22) (7.28) (8.27) (10.24) (11.14) (12.09) (13.19) (14.33) (15.39) (17.32) kg 6.0 10.5 12.5 15.5 23.3 32.0 35.4 60.0 68.0 97.0 128 163 213 249 339 Weight (kg) (lb) (13.2) (23.1) (27.6) (34.2) (51.4) (70.5) (78.0) (132) (150) (214) (282) (359) (470) (549) (747) Note) 1. This table is for remote detectors. 2. An integral detector includes an integral converter instead of a terminal box. 3. The table indicates dimensions for ANSI 150 flange. - 26 - Yamatake Corporation No. SS2-MGG200-0100 SS2-MGG200-0100 (Rev.7) Flange type (size 700 to 900 mm (28 to 36 inches) H Flange type (size 1000, 1100 mm (40, 44 inches) mm Face to face dimension L H H1 Height H2 H3 Feet length W Feet width A Feet halls * n-d Weight 700 800 900 1000 1100 (inches) Size (28) (32) (36) (40) (44) mm (inches) mm (inches) mm (inches) mm (inches) mm (inches) mm (inches) mm (inches) mm (inches) kg (lb) 1100 (43.31) 979 (38.54) 503 (19.80) 429 (16.89) 454 (17.87) 1049 (41.30) 600 (23.62) 4-33 (1.30) 630.0 (1389) 1200 (47.24) 1080 (42.52) 554 (21.81) 480 (18.90) 505 (19.88) 1145 (45.08) 600 (23.62) 4-33 (1.30) 720.0 (1587) 1300 (51.18) 1211 (47.68) 634 (24.96) 530 (20.87) 555 (21.85) 1245 (49.02) 600 (23.62) 4-33 (1.30) 1060.0 (2337) 1500 (59.06) 1278 (50.31) 650 (25.59) 581 (22.87) 606 (23.86) 980 (38.58) 800 (31.50) 4-33 (1.30) 1320.0 (2910) 1500 (59.06) 1399 (55.08) 720 (28.35) 632 (24.88) 657 (25.87) 1000 (39.37) 800 (31.50) 4-33 (1.30) 1540.0 (3395) Note) The table indicates dimensions for ANSI 150 flange. *: n = number, d = diameter - 27 - Savemation Totate international Building 2-12-19 Shibuya Shibuya-ku, Tokyo 150-8316 Japan Tel : 81-3-3486-2310 Fax : 81-3-3486-2593 Saving through Automation http://www.yamatake.com/ This has been printed on recycled paper.