MC74AC05 MC74ACT05 MC74AC/ACT05 ACT05 MC74AC05DT MC74AC05DTR2 MC74ACT05DT - Datasheet Archive

 

Hex Inverter with Open-Drain Outputs The MC74AC/ACT05 is identical in pinout to the LS05. The device inputs are compatible with

 

MC74AC05 MC74AC05, MC74ACT05 MC74ACT05 Hex Inverter with Open-Drain Outputs The MC74AC/ACT05 MC74AC/ACT05 is identical in pinout to the LS05. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with TTL outputs. http://onsemi.com · Outputs Source/Sink 24 mA · ACT05 ACT05 Has TTL Compatible Inputs VCC A6 Y6 A5 Y5 A4 Y4 14 13 12 11 10 9 PDIP­14 N SUFFIX CASE 646 8 14 1 SO­14 D SUFFIX CASE 751A 14 1 1 2 3 4 5 6 A1 Y1 A2 Y2 A3 Y3 14 7 GND 1 Figure 1. Pinout: 14-Lead Packages (Top View) 14 1 TSSOP­14 DT SUFFIX CASE 948G EIAJ­14 M SUFFIX CASE 965 FUNCTION TABLE Input A Output Y L H Z L ORDERING INFORMATION SOIC­14 55 Units/Rail SOIC­14 2500 Tape & Reel SOIC­14 55 Units/Rail SOIC­14 2500 Tape & Reel MC74AC05DT MC74AC05DT TSSOP­14 96 Units/Rail MC74AC05DTR2 MC74AC05DTR2 TSSOP­14 2500 Tape & Reel MC74ACT05DT MC74ACT05DT PIN 14 = VCC PIN 7 = GND * DENOTES OPENDRAIN OUTPUTS 25 Units/Rail MC74ACT05DR2 MC74ACT05DR2 1, 3, 5, 9, 11, 13 PDIP­14 MC74ACT05D MC74ACT05D A 25 Units/Rail MC74AC05DR2 MC74AC05DR2 Y* PDIP­14 MC74AC05D MC74AC05D 2, 4, 6, 8, 10, 12 Shipping MC74AC05N MC74AC05N Z = High Impedance Package MC74ACT05N MC74ACT05N NOTE: Device TSSOP­14 MC74ACT05DTR2 MC74ACT05DTR2 TSSOP­14 2500 Tape & Reel 96 Units/Rail EIAJ­14 50 Units/Rail MC74AC05MEL MC74AC05MEL EIAJ­14 2000 Tape & Reel MC74ACT05M MC74ACT05M EIAJ­14 50 Units/Rail MC74ACT05MEL MC74ACT05MEL Figure 2. Logic Diagram MC74AC05M MC74AC05M EIAJ­14 2000 Tape & Reel DEVICE MARKING INFORMATION See general marking information in the device marking section on page 5 of this data sheet. © Semiconductor Components Industries, LLC, 2001 May, 2001 ­ Rev. 5 1 Publication Order Number: MC74AC05/D MC74AC05/D MC74AC05 MC74AC05, MC74ACT05 MC74ACT05 MAXIMUM RATINGS* Symbol Parameter Value Unit VCC DC Supply Voltage (Referenced to GND) ­0.5 to +7.0 V Vin DC Input Voltage (Referenced to GND) ­0.5 to VCC + 0.5 V Vout DC Output Voltage (Referenced to GND) ­0.5 to VCC + 0.5 V Iin DC Input Current, per Pin ± 20 mA Iout DC Output Sink/Source Current, per Pin ± 50 mA ICC DC VCC or GND Current per Output Pin ± 50 mA Tstg Storage Temperature ­65 to +150 °C *Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. RECOMMENDED OPERATING CONDITIONS Symbol VCC VREG Parameter Min Min AC 2.0 5.0 6.0 ACT Supply Voltage Typ 4.5 5.0 5.5 ­ 40 ­ ­ 25 ­ ­ 10 ­ VCC @ 5.5 V ­ 8.0 V ­ VCC @ 4.5 V In ut Input Rise and Fall Time (Note 2) ACT Devices except Schmitt Inputs VCC 150 VCC @ 4.5 V Input Rise and Fall Time (Note 1) I Ri d F ll Ti (N ) AC Devices except Schmitt Inputs ­ ­ VCC @ 5.5 V tr, tf 0 VCC @ 3.0 V tr, tf DC Regulated Power Voltage (Ref. to GND) Unit V ­ ns/V ns/V ­ ­ 140 °C ­40 25 85 °C Output Current ­ HIGH ­ ­ ­24 mA Output Current ­ LOW ­ ­ 24 mA TJ Junction Temperature (PDIP) TA Operating Ambient Temperature Range IOH IOL 1. Vin from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times. 2. Vin from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times. http://onsemi.com 2 MC74AC05 MC74AC05, MC74ACT05 MC74ACT05 DC CHARACTERISTICS 74AC Symbol Parameter TA = +25°C VCC (V) 74AC TA = ­40°C to +85°C Typ VIH Unit Conditions Guaranteed Limits VOL 3.0 4.5 5.5 1.5 2.25 2.75 2.1 3.15 3.85 2.1 3.15 3.85 V VOUT = 0.1 V or VCC ­ 0.1 V Maximum Low Level Input Voltage 3.0 4.5 5.5 1.5 2.25 2.75 0.9 1.35 1.65 0.9 1.35 1.65 V VOUT = 0.1 V or VCC ­ 0.1 V Maximum Low Level Output Voltage 3.0 4.5 5.5 0.002 0.001 0.001 0.1 0.1 0.1 0.1 0.1 0.1 V 3.0 4.5 5.5 VIL Minimum High Level g Input Voltage ­ ­ ­ 0.36 0.36 0.36 0.44 0.44 0.44 5.5 55 ­ ±0.1 ±0 1 5.5 ­ 5.5 5.5 55 IIN Maximum Input Leakage Current IOLD Minimum Dynamic Output C O t t Current t IOHD ICC Maximum Q Quiescent Supply Current IOUT = 50 µA V *VIN = VIL or VIH 12 mA IOL 24 mA 24 mA ±1.0 ±1 0 µA VI = VCC, GND ­ 75 mA VOLD = 1.65 V Max ­ ­ ­75 mA VOHD = 3.85 V Min ­ 4.0 40 40 µA VIN = VCC or GND *All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. NOTE: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V. AC CHARACTERISTICS 74AC Symbol TA = +25°C CL = 50 pF VCC* (V) Parameter 74AC TA = ­40°C to +85°C CL = 50 pF Min Typ Max Min Unit Max tPZL Propagation Delay g y Output Enable 3.3 5.0 1.5 1.5 ­ ­ 8.0 6.0 1.0 1.0 9.0 6.5 ns tPLZ Propagation Delay g y Output Enable 3.3 5.0 1.5 1.5 ­ ­ 8.0 6.0 1.0 1.0 9.0 6.5 ns *Voltage Range 3.3 V is 3.3 V ±0.3 V. Voltage Range 5.0 V is 5.0 V ±0.5 V. http://onsemi.com 3 MC74AC05 MC74AC05, MC74ACT05 MC74ACT05 DC CHARACTERISTICS 74ACT 74ACT Symbol Parameter TA = +25°C VCC (V) 74ACT 74ACT TA = ­40°C to +85°C Typ Unit Conditions Guaranteed Limits VIH Minimum High Level g Input Voltage 4.5 5.5 1.5 1.5 2.0 2.0 2.0 2.0 V VOUT = 0.1 V or VCC ­ 0.1 V VIL Maximum Low Level Input Voltage 4.5 5.5 1.5 1.5 0.8 0.8 0.8 0.8 V VOUT = 0.1 V or VCC ­ 0.1 V VOL Maximum Low Level Output Voltage 4.5 5.5 0.001 0.001 0.1 0.1 0.1 0.1 V 4.5 5.5 ­ ­ 0.36 0.36 0.44 0.44 V *VIN = VIL or VIH 24 mA IOH 24 mA IOUT = 50 µA IIN Maximum Input Leakage Current 5.5 55 ­ ±0.1 ±0 1 ±1.0 ±1 0 µA VI = VCC, GND ICCT Additional Max. ICC/Input 5.5 0.6 ­ 1.5 mA VI = VCC ­ 2.1 V IOLD Minimum Dynamic Output C O t t Current t 5.5 ­ ­ 75 mA VOLD = 1.65 V Max 5.5 ­ ­ ­75 mA VOHD = 3.85 V Min 5.5 55 ­ 4.0 40 40 µA VIN = VCC or GND IOHD ICC Maximum Q Quiescent Supply Current *All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. AC CHARACTERISTICS 74ACT 74ACT Symbol TA = +25°C CL = 50 pF VCC* (V) Parameter 74ACT 74ACT TA = ­40°C to +85°C CL = 50 pF Min Typ Max Min Unit Max tPZL Pro agation Propagation Delay Output Enable 5.0 50 1.5 15 ­ 8.0 80 1.0 10 8.5 85 ns tPLZ Pro agation Propagation Delay Output Enable 5.0 50 1.5 15 ­ 8.5 85 1.0 10 9.0 90 ns *Voltage Range 5.0 V is 5.0 V ±0.5 V. CAPACITANCE Symbol Value Typ Parameter Unit Test Conditions CIN Input Capacitance 4.5 pF VCC = 5.0 V CPD Power Dissipation Capacitance 30 pF VCC = 5.0 V http://onsemi.com 4 MC74AC05 MC74AC05, MC74ACT05 MC74ACT05 MARKING DIAGRAMS PDIP­14 SO­14 TSSOP­14 EIAJ­14 MC74AC05N MC74AC05N AWLYYWW AC05 AWLYWW AC 05 ALYW 74AC05 74AC05 ALYW MC74ACT05N MC74ACT05N AWLYYWW ACT05 ACT05 AWLYWW ACT 05 ALYW 74ACT05 74ACT05 ALYW A WL, L YY, Y WW, W = Assembly Location = Wafer Lot = Year = Work Week http://onsemi.com 5 MC74AC05 MC74AC05, MC74ACT05 MC74ACT05 PACKAGE DIMENSIONS PDIP­14 N SUFFIX 14 PIN PLASTIC DIP PACKAGE CASE 646­06 ISSUE M 14 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. 8 B 1 7 A F DIM A B C D F G H J K L M N L N C ­T­ SEATING PLANE J K H D 14 PL G 0.13 (0.005) M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. ­A­ 8 ­B­ 1 P 7 PL 0.25 (0.010) 7 G M B M F R X 45 _ C ­T­ SEATING PLANE D 14 PL 0.25 (0.010) M T B J M K S A MILLIMETERS MIN MAX 18.16 18.80 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.37 7.87 -10_ 0.38 1.01 M SO­14 D SUFFIX 14 PIN PLASTIC SOIC PACKAGE CASE 751A­03 ISSUE F 14 INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.290 0.310 -10_ 0.015 0.039 S http://onsemi.com 6 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 MC74AC05 MC74AC05, MC74ACT05 MC74ACT05 PACKAGE DIMENSIONS TSSOP­14 DT SUFFIX 14 PIN PLASTIC TSSOP PACKAGE CASE 948G­01 ISSUE O NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. 14X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S S N 2X 14 L/2 0.25 (0.010) 8 M B ­U­ L PIN 1 IDENT. F 7 1 S DETAIL E K A ­V­ K1 J J1 DIM A B C D F G H J J1 K K1 L M ÉÉ ÇÇ ÉÉÇ ÇÇÇ 0.15 (0.006) T U N SECTION N­N ­W­ C 0.10 (0.004) ­T­ SEATING PLANE H G D DETAIL E EIAJ­14 M SUFFIX 14 PIN PLASTIC EIAJ PACKAGE CASE 965­01 ISSUE O 14 LE 8 Q1 E HE L 7 1 M_ DETAIL P Z D VIEW P A e c b 0.13 (0.005) A1 M 0.10 (0.004) http://onsemi.com 7 MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 -1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.50 0.60 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 -0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.020 0.024 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). DIM A A1 b c D E e HE 0.50 LE M Q1 Z MILLIMETERS MIN MAX -2.05 0.05 0.20 0.35 0.50 0.18 0.27 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 0_ 10 _ 0.70 0.90 -1.42 INCHES MIN MAX -0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 0_ 10 _ 0.028 0.035 -0.056 MC74AC05 MC74AC05, MC74ACT05 MC74ACT05 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303­675­2175 or 800­344­3860 Toll Free USA/Canada Fax: 303­675­2176 or 800­344­3867 Toll Free USA/Canada Email: ONlit@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4­32­1 Nishi­Gotanda, Shinagawa­ku, Tokyo, Japan 141­0031 Phone: 81­3­5740­2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800­282­9855 Toll Free USA/Canada http://onsemi.com 8 MC74AC05/D MC74AC05/D