MC10H601 MC100H601 MC10H/100H601 DL122 MC10H601/D - Datasheet Archive

 

SEMICONDUCTOR TECHNICAL DATA 9-Bit ECL/TTL Translator MC10H601 MC100H601 The MC10H/100H601 is a 9­bit, dual supply ECL to TTL

 

MOTOROLA SEMICONDUCTOR TECHNICAL DATA 9-Bit ECL/TTL Translator MC10H601 MC10H601 MC100H601 MC100H601 The MC10H/100H601 MC10H/100H601 is a 9­bit, dual supply ECL to TTL translator. Devices in the Motorola 9­bit translator series utilize the 28­lead PLCC for optimal power pinning, signal flow­through and electrical performance. The devices feature a 48 mA TTL output stage, and AC performance is specified into both a 50 pF and 200 pF load capacitance. For the 3­state output disable, both ECL and TTL control inputs are provided, allowing maximum design flexibility. The 10H version is compatible with MECL 10H ECL logic levels. The 100H version is compatible with 100K levels. · · · · · · · · 9­Bit Ideal for Byte­Parity Applications 3­State TTL Outputs Flow­Through Configuration Extra TTL and ECL Power Pins to Minimize Switching Noise ECL and TTL 3­State Control Inputs Dual Supply 4.8 ns Max Delay into 50 pF, 9.6 ns into 200 pF (all outputs switching) PNP TTL Inputs for Low Loading FN SUFFIX 28­LEAD PLASTIC PLCC PACKAGE CASE 776­02 PIN NAMES PIN GND VCCE VCCT VEE D0 ­ D8 Q0 ­ Q8 OEECL OETTL OEECL OETTL FUNCTION TTL Ground (0 V) ECL VCC (0 V) TTL Supply (+ 5.0 V) ECL Supply (­ 5.2 / ­ 4.5 V) Data Inputs (ECL) Data Outputs (TTL) 3­State Control (ECL) 3­State Control (TTL) TRUTH TABLE D0 Q0 D1 Q1 D2 Q2 D3 Q3 OEECL OETTL D Q L L H X L L X H L H X X L H Z Z Q5 GND VCCT Q6 GND Q7 Q8 25 24 23 22 21 20 19 Q4 Q4 D4 D5 D8 Q3 27 17 D7 28 16 VCCE 15 D6 TTL Q5 D6 18 VCCT ECL 26 Q6 Q2 GND 2 14 D5 Q1 3 13 D4 Q0 4 12 D3 5 6 7 8 9 10 Q7 D7 OETTL NC OEECL VEE D0 D1 Q8 D8 10/97 2­1 D2 Figure 1. 28­Lead Pinout (Top View) Figure 2. Logic Diagram © Motorola, Inc. 1997 11 REV 7 MC10H601 MC10H601 MC100H601 MC100H601 10H ECL DC CHARACTERISTICS: VCCT = 5.0 V ± 10%; VEE = ­ 5.2 V ± 5% 0°C Symbol S b l Parameter P Min 25°C Max Min 85°C Max Max Min Unit U i IEE Power Supply Current ­ 51 ­ 51 ­ 51 mA IIH IIL Input HIGH Current Input LOW Current 225 145 145 0.5 µA µA VIH VIL Input HIGH Voltage Input LOW Voltage ­1170 ­1950 ­ 720 ­1445 Condition C di i mV 0.5 ­ 840 ­1480 0.5 ­1130 ­1950 ­ 810 ­1480 ­1060 ­1950 100H ECL DC CHARACTERISTICS: VCCT = 5.0 V ± 10%; VEE = ­ 4.2 V to ­ 5.5 V 0°C Symbol S b l Parameter P Min 25°C Max IEE Power Supply Current IIH IIL Input HIGH Current Input LOW Current 0.5 VIH VIL Input HIGH Voltage Input LOW Voltage ­1165 ­1810 Min 85°C Max ­ 51 Min Max Unit U i ­ 53 mA 145 µA µA ­ 880 ­1475 mV ­ 51 225 145 0.5 ­ 880 ­1475 0.5 ­1165 ­1810 ­ 880 ­1475 ­1165 ­1810 Condition C di i TTL DC CHARACTERISTICS: VCCT = 5.0 V ± 10%; VEE = ­ 5.2 V ± 5% (10H version); VEE = ­ 4.2 V to ­ 5.5 V (100H version) 0°C Symbol S b l Parameter P Min 25°C Max Min 85°C Max ICCH ICCL Power Supply Current ICCZ IIH IIL Input LOW Current IOS Output Short Circuit Current IOZH IOZL Output Disable Current HIGH Output Disable Current LOW VIHT VILT Input HIGH Voltage Input LOW Voltage 2.0 VOHT Output HIGH Voltage 2.5 2.0 VOLT Output LOW Voltage 0.55 0.55 VIK Input Clamp Voltage ­1.2 Max Min ­1.2 Unit U i Condition C di i mA 110 110 110 110 110 110 Power Supply Current 105 105 105 Input HIGH Current 20 100 20 100 20 100 µA VIN = 2.7 V VIN = 7.0 V ­ 0.6 ­100 ­ 0.6 ­ 225 ­100 ­ 225 50 ­ 50 ­ 0.6 mA VIN = 0.5 V ­ 225 mA VOUT = 0 V 50 ­ 50 ­100 µA VOUT = 2.7 V VOUT = 0.5 V 50 ­ 50 2.0 2.0 0.8 V 0.8 2.5 2.0 0.8 2.5 2.0 V IOH = ­ 3.0 mA IOH = ­15 mA 0.55 V IOL = 48 mA ­1.2 V IIN = ­18 mA AC CHARACTERISTICS: VCCT = 5.0 V ± 10%; VEE = ­ 5.2 V ± 5% (10H version); VEE = ­ 4.2 V to ­ 5.5 V (100H version) 0°C Symbol S b l Parameter P Output Disable Time Max Min Max Unit U i 1.7 3.4 4.8 9.6 1.7 3.4 4.8 9.6 1.7 3.4 4.8 9.6 ns ns CL = 50 pF CL = 200 pF OEECL 3.7 5.4 6.5 13 3.7 5.4 6.5 13 3.7 5.4 6.5 13 ns ns CL = 50 pF CL = 200 pF 4.3 7.0 7.5 15 4.3 7.0 7.5 15 4.3 7.0 7.5 15 ns ns CL = 50 pF CL = 200 pF OEECL 3.5 5.0 6.0 12 3.5 5.0 6.0 12 3.5 5.0 6.0 12 ns ns CL = 50 pF CL = 200 pF OETTL tPLZ tPHZ Min 4.2 6.0 7.0 14 4.2 6.0 7.0 14 4.2 6.0 7.0 14 ns ns CL = 50 pF CL = 200 pF 1.2 3.0 ns ns CL = 50 pF CL = 200 pF Propagation Delay to Output tPLZ tPHZ Output Enable Time tPZL tPZH tR tF 85°C Max OETTL tPLH tPHL tPZL tPZH 25°C Min Output Rise/Fall Time 1.0 V ­ 2.0 V MOTOROLA 1.2 3.0 1.2 3.0 2­2 Condition C di i MECL Data DL122 DL122 - Rev 6 MC10H601 MC10H601 MC100H601 MC100H601 OUTLINE DIMENSIONS FN SUFFIX PLASTIC PLCC PACKAGE CASE 776­02 ISSUE D 0.007 (0.180) B T L­M M N S T L­M S S Y BRK ­N­ 0.007 (0.180) U M N S D Z ­M­ ­L­ W 28 D X G1 0.010 (0.250) T L­M S N S S V 1 VIEW D­D A 0.007 (0.180) R 0.007 (0.180) M T L­M S N S C M T L­M S N 0.007 (0.180) H Z M T L­M N S S S K1 E 0.004 (0.100) G J S K SEATING PLANE F VIEW S G1 0.010 (0.250) ­T­ T L­M S N S M T L­M S N S VIEW S NOTES: 1. DATUMS ­L­, ­M­, AND ­N­ DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM ­T­, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). MECL Data DL122 DL122 - Rev 6 0.007 (0.180) 2­3 DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 ­­­ 0.025 ­­­ 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 ­­­ 0.020 2_ 10_ 0.410 0.430 0.040 ­­­ MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 ­­­ 0.64 ­­­ 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 ­­­ 0.50 2_ 10_ 10.42 10.92 1.02 ­­­ MOTOROLA MC10H601 MC10H601 MC100H601 MC100H601 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1­303­675­2140 or 1­800­441­2447 JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4­32­1, Nishi­Gotanda, Shinagawa­ku, Tokyo 141, Japan. 81­3­5487­8488 Customer Focus Center: 1­800­521­6274 MfaxTM: RMFAX0@email.sps.mot.com ­ TOUCHTONE 1­602­244­6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, Motorola Fax Back System ­ US & Canada ONLY 1­800­774­1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852­26629298 ­ http://sps.motorola.com/mfax/ HOME PAGE: http://motorola.com/sps/ MOTOROLA 2­4 MC10H601/D MC10H601/D MECL Data DL122 DL122 - Rev 6