MAX660 /883B GDIP1-T08 CDIP2-T08 CQCC1-N20 MAX660/883B MAX660MJA/883B

100mA CMOS SWITCHED-CAPACITOR VOLTAGE CONVERTER 1.5V TO 5.5V Device Type 01 Generic Number MAX660(x)/883B SMD Number 5962-94632

SCOPE: 100mA CMOS SWITCHED-CAPACITOR VOLTAGE CONVERTER 1.5V TO 5.5V Device Type 01 Generic Number MAX660 MAX660(x)/883B /883B SMD Number 5962-94632 Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows: Outline Letter Maxim SMD JA P LP 2 Mil-Std-1835 Case Outline Package Code GDIP1-T08 GDIP1-T08 or CDIP2-T08 CDIP2-T08 CQCC1-N20 CQCC1-N20 8 LEAD CERDIP 20 Leadless chip carrier J08 L20 Absolute Maximum Ratings Voltage Referenced to VSupply Voltage (V+ to GND, or GND to OUT) . +6V LV Input Voltage . OUT -0.3V to V+ +0.3V FC and OSC Input Voltages . (the least negative of OUT -0.3V or V+-6V) to V+ +0.3V OUT and V+ Continuous Output Current. 120mA Output Short-Circuit Duration to GND (Note 1) . 1 sec Lead Temperature (soldering, 10 seconds) . +300°C Storage Temperature . -65°C to +150°C Continuous Power Dissipation . TA=+70°C 8 lead CERDIP(derate 8.0mW/°C above +70°C) . 640mW 20 lead LCC(derate 9.09mW/°C above +70°C) . 727mW Junction Temperature TJ . +150°C Thermal Resistance, Junction to Case, JC: Case Outline 8 lead CERDIP. 55°C/W Case Outline 20 lead LCC . 20°C/W Thermal Resistance, Junction to Ambient, JA: Case Outline 8 lead CERDIP. 125°C/W Case Outline 20 lead LCC . 110°C/W Recommended Operating Conditions Ambient Operating Range (TA) . -55°C to +125°C Inverter mode V+ to GND . +1.5V dc to +5.5V dc Doubler mode GND to VOUT . +2.5V dc to +5.5V dc NOTE 1: OUT may be shorted to GND for 1 sec without damage, but shorting OUT to V+ may damage the device and should be avoided. Also, for temperatures above +85°C, OUT must not be shorted to GND or V+, even instantaneously, or device damage may result. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. - Electrical Characteristics of MAX660/883B MAX660/883B for /883B /883B and SMD 5962-94632 19-0251 Page 2 of Rev. C 5 TABLE 1. ELECTRICAL TESTS: TEST CONDITIONS -55 °C TA +125°C 2/ V+=5.0V, C1, C2=150µF, FC=open Unless otherwise specified RL=1k, Inverter, LV=open RL=1k, Inverter, LV=GND RL=1k, Doubler, LV=OUT No load, FC=open No load, FC=V+ OUT more negative than -4V Symbol Operating Supply Voltage Supply Current Output Current Group A Subgroup Device type 1,2,3 All 1,2,3 Output Resistance NOTE 3 Oscillator Frequency ROUT Voltage Conversion Efficiency Limits Max 5.5 5.5 5.5 0.5 3.0 IL=100mA FC=open 2 1,2,3 FC=V+ RL=1k, connected between V+ and OUT RL=500 connected between OUT and GND No Load VCEFF 100 ORDERING INFORMATION: MAX660MJA/883B MAX660MJA/883B MAX660MLP/883B MAX660MLP/883B TERMINAL CONNECTIONS: J8 L20 1 FC NC 2 CAP+ FC 3 GND NC 4 CAPCAP+ 5 OUT GND 6 LV GND 7 OSC NC 8 V+ CAP9 NC 10 NC - 11 12 13 14 15 16 17 18 19 20 mA mA 10 12 All 5 1,2,3 1,2,3 All 40 96 1,2,3 All 92 1 All 99 All kHz % % NOTE 2: In the test circuit, capacitors C1 and C2 are 150µF, 0.2 maximum ESR, aluminum electrolytics (Maxim part # MAXC001 MAXC001). Capacitors with higher ESR may reduce output voltage and efficiency. NOTE 3: Specified output resistance is a combination of internal switch resistance and capacitor ESR. Package 8 pin CERDIP 20 pin LCC V 2 All PEFF Units 1,3 1,3 IL=100mA fOSC Power Efficiency 3.0 1.5 2.5 All All OUT more negative than -3.8V Limits Min SMD Number 5962-9463201MPA 5962-9463201MPA 5962-9463201M2C 5962-9463201M2C L20 OUT NC NC NC LV NC OSC NC NC V+ Electrical Characteristics of MAX660/883B MAX660/883B for /883B /883B and SMD 5962-94632 19-0251 Page 3 of Rev. C 5 QUALITY ASSURANCE Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in MilStd-883. Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015: 1. Test Condition, A, B, C, or D. 2. TA = +125°C minimum. 3. Interim and final electrical test requirements shall be specified in Table 2. Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B, C, and D inspection. Group A inspection: 1. Tests as specified in Table 2. 2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted. Group C and D inspections: a. End-point electrical parameters shall be specified in Table 1. b. Steady-state life test, Method 1005 of Mil-Std-883: 1. Test condition A, B, C, D. 2. TA = +125°C, minimum. 3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883. TABLE 2. ELECTRICAL TEST REQUIREMENTS Mil-Std-883 Test Requirements Interim Electric Parameters Method 5004 Final Electrical Parameters Method 5005 Group A Test Requirements Method 5005 Group C and D End-Point Electrical Parameters Method 5005 * Subgroups per Method 5005, Table 1 1 1*, 2, 3 1, 2, 3 1 PDA applies to Subgroup 1 only. - Electrical Characteristics of MAX660/883B MAX660/883B for /883B /883B and SMD 5962-94632 19-0251 Page 4 of Rev. C 5