LTM4604 LTM4604A 66-PIN LTM4604EV LTM4604V LTM4604IV LTM4604E LTM4604I D8-D11 - Datasheet Archive

 

Low Voltage, 4A DC/DC µModule® Regulator with Tracking DESCRIPTION FEATURES n n n n n n n n n n Complete Standalone

 

LTM4604 LTM4604 Low Voltage, 4A DC/DC µModule® Regulator with Tracking DESCRIPTION FEATURES n n n n n n n n n n Complete Standalone Power Supply Wide Input Voltage Range: 2.375V to 5.5V 4A DC, 5A Peak Output Current 0.8V to 5V Output Output Voltage Tracking ±2% Total DC Error UltraFastTM Transient Response Current Mode Control Current Foldback Protection, Parallel/Current Sharing Small and Very Low Profile Package: 15mm × 9mm × 2.3mm LGA APPLICATIONS n n n Telecom and Networking Equipment Servers, ATCA Cards Industrial Equipment For easier PC board layout and assembly due to increased spacing between land grid pads, please refer to the LTM4604A LTM4604A. The LTM®4604 is a complete 4A switch mode DC/DC power supply. Included in the package are the switching controller, power FETs, inductor and all support components. Operating over an input voltage range of 2.375V to 5.5V, the LTM4604 LTM4604 supports an output voltage range of 0.8V to 5V, set by a single resistor. This high efficiency design delivers up to 4A continuous current (5A peak). Only bulk output capacitors are needed to complete the design. The low profile package (2.3mm) enables utilization of unused space on the bottom of PC boards for high density point of load regulation. High switching frequency and a current mode architecture enable a very fast transient response to line and load changes without sacrificing stability. The device supports output voltage tracking for supply rail sequencing. Fault protection features include foldback current protection, thermal shutdown and a programmable soft-start function. The LTM4604 LTM4604 is offered in a space saving and thermally enhanced 15mm × 9mm × 2.3mm LGA package and is Pb free and RoHS compliant. L, LT, LTC, LTM, Linear Technology, the Linear logo and Module are registered trademarks of Linear Technology Corporation. UltraFast is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION Efficiency vs Output Current 3.3V to 2.5V/4A Module Regulator 100 VIN 3.3V VIN = 3.3V VOUT = 2.5V 95 10F 6.3V PGOOD VOUT 2.5V 4A VOUT LTM4604 LTM4604 COMP FB RUN/SS TRACK GND VIN 2.37k 22F 6.3V 2 EFFICIENCY (%) 90 VIN 85 80 75 70 4604 TA01a 65 0 1 2 3 OUTPUT CURRENT (A) 4 4604 G02 4604fa 1 LTM4604 LTM4604 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Note 1) TOP VIEW TRACK VIN, PGOOD . ­0.3V to 6V COMP, RUN/SS, FB, TRACK . ­0.3V to VIN SW, VOUT . ­0.3V to (VIN + 0.3V) Operating Temperature Range (Note 2) .­40°C to 85°C Junction Temperature . 125°C Storage Temperature Range . ­55°C to 125°C A B PGOOD C F D E G VIN COMP 1 2 RUN/ SS SW 3 FB GND 4 5 6 7 8 9 10 11 GND For easier PC board layout and assembly due to increased spacing between land grid pads, please refer to the LTM4604A LTM4604A. VOUT LGA PACKAGE 66-PIN 66-PIN (15mm 9mm 2.3mm) TJMAX = 125°C, JA = 25°C/W, JC(BOT) = 7°C/W, JC(TOP) = 35°C/W, WEIGHT = 0.86g ORDER INFORMATION LEAD FREE FINISH TRAY PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTM4604EV LTM4604EV#PBF LTM4604EV LTM4604EV#PBF LTM4604V LTM4604V 15mm × 9mm × 2.3mm LGA ­40°C to 85°C LTM4604IV LTM4604IV#PBF LTM4604IV LTM4604IV#PBF LTM4604V LTM4604V 15mm × 9mm × 2.3mm LGA ­40°C to 85°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ This product is only offered in trays. For more information go to: http://www.linear.com/packaging/ ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 5V unless otherwise noted. See Figure 15. SYMBOL VIN(DC) VOUT(DC) PARAMETER CONDITIONS Input DC Voltage Output Voltage, Total Variation CIN = 10F × 1, COUT = 22F ×3, RFB = 5.69k 0.5% with Line and Load VIN = 2.375V to 5.5V, IOUT = 0A to 4A, 0°C TA 85°C VIN = 2.375V to 5.5V, IOUT = 0A to 4A Input Specifications Undervoltage Lockout VIN(UVLO) Threshold Peak Input Inrush Current at IINRUSH(VIN) Start-Up IQ(VIN NOLOAD) Input Supply Bias Current IOUT = 0A IOUT = 0A, CIN = 10F COUT = 22F ×3, , RUN/SS = 0.01F VOUT = 1.5V , VIN = 3.3V VIN = 5V VIN = 3.3V, VOUT = 1.5V, No Switching VIN = 3.3V, VOUT = 1.5V, Switching Continuous VIN = 5V, VOUT = 1.5V, No Switching VIN = 5V, VOUT = 1.5V, Switching Continuous Shutdown, RUN = 0, VIN = 5V MIN 2.375 TYP l MAX 5.5 UNITS V l 1.478 1.470 1.5 1.5 1.522 1.522 V V 1.75 2 2.3 V 0.7 0.7 60 28 100 35 7 A A A mA A mA A 4604fa 2 LTM4604 LTM4604 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 5V unless otherwise noted. See Figure 15. SYMBOL IS(VIN) PARAMETER Input Supply Current Output Specifications IOUT(DC) Output Continuous Current Range (See Output Current Derating Curves for Different VIN, VOUT and TA) Line Regulation Accuracy VOUT(LINE) VOUT VOUT(LOAD) Load Regulation Accuracy VOUT VOUT(AC) fS VOUT(START) tSTART VOUT(LS) tSETTLE IOUT(PK) Control Section VFB IFB VRUN ITRACK VTRACK(OFFSET) VTRACK(RANGE) RFBHI PGOOD VPGOOD RPGOOD Output Ripple Voltage Output Ripple Voltage Frequency Turn-On Overshoot Turn-on Time Peak Deviation for Dynamic Load Step Settling Time for Dynamic Load Step Output Current Limit Voltage at FB Pin RUN Pin On/Off Threshold TRACK Pin Current Offset Voltage Tracking Input Range Resistor Between VOUT and FB Pins PGOOD Range PGOOD Resistance CONDITIONS VIN = 2.5V, VOUT = 1.5V, IOUT = 4A VIN = 3.3V, VOUT = 1.5V, IOUT = 4A VIN = 5V, VOUT = 1.5V, IOUT = 4A MIN TYP 2.9 2.2 1.45 VIN = 3.3V, VOUT = 1.5V VOUT = 1.5V, 0A to 4A VIN = 3.3V VIN = 5V IOUT = 0A, COUT = 22F/X5R/Ceramic ×3 VIN = 3.3V, VOUT = 1.5V VIN = 5V, VOUT = 1.5V IOUT = 4A, VIN = 5V, VOUT = 1.5V IOUT = 0A, VOUT = 1.5V, 0°C TA 85°C IOUT = 0A, VOUT = 1.5V A l 0.1 0.2 % l l 0.3 0.3 0.6 0.6 % % 10 12 1.25 COUT = 22F ×3, VOUT = 1.5V, RUN/SS = 10nF , IOUT = 0A VIN = 3.3V VIN = 5V COUT = 22F ×3, VOUT = 1.5V, IOUT = 1A Resistive Load, TRACK = VIN and RUN/SS = Float VIN = 3.3V VIN = 5V Load: 0% to 50% to 0% of Full Load, COUT = 22F ×3 Ceramic VIN = 5V, VOUT = 1.5V Load: 0% to 50% to 0% of Full Load VIN = 5V, VOUT = 1.5V COUT = 22F ×3 VIN = 3.3V, VOUT = 1.5V VIN = 5V, VOUT = 1.5V mVP-P mVP-P MHz 20 20 0 4.975 s 8 8 TRACK = 0.4V mV 10 0.792 0.788 ms ms 25 l mV mV 1.5 1.0 0.5 Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. UNITS A A A 4 VOUT = 1.5V, VIN from 2.375V to 5.5V, IOUT = 0A Open-Drain Pull-Down MAX A A 0.8 0.8 0.2 0.65 0.2 30 4.99 ±7.5 90 0.808 0.812 0.8 5.025 V V A V A mV V k 150 % 0.8 Note 2: The LTM4604E LTM4604E is guaranteed to meet performance specifications from 0°C to 85°C. Specifications over the ­ 40°C to 85°C operating temperature range are assured by design, characterization and correlation with statistical process controls. The LTM4604I LTM4604I is guaranteed over the full ­40°C to 85°C operating temperature range. 4604fa 3 LTM4604 LTM4604 TYPICAL PERFORMANCE CHARACTERISTICS Efficiency vs Output Current VIN = 2.5V Efficiency vs Output Current VIN = 3.3V Efficiency vs Output Current VIN = 5V 95 95 90 90 90 85 80 75 65 0 1 85 80 VOUT = 2.5V VOUT = 1.8V VOUT = 1.5V VOUT = 1.2V VOUT = 0.8V 75 VOUT = 1.8V VOUT = 1.5V VOUT = 1.2V VOUT = 0.8V 70 EFFICIENCY (%) 95 EFFICIENCY (%) 100 EFFICIENCY (%) 100 70 2 4 3 OUTPUT CURRENT (A) 65 0 1 65 2 VOUT (V) 2.5 1 2 3 OUTPUT CURRENT (A) 4 4604 G03 Load Transient Response ILOAD 2A/DIV ILOAD 2A/DIV 2.0 0 4 3 OUTPUT CURRENT (A) Load Transient Response VOUT = 3.3V VOUT = 2.5V VOUT = 1.8V VOUT = 1.5V VOUT = 1.2V VOUT = 0.8V VOUT = 3.3V VOUT = 2.5V VOUT = 1.8V VOUT = 1.5V VOUT = 1.2V VOUT = 0.8V 75 4604 G02 Minimum Input Voltage at 4A Load 3.0 80 70 4604 G01 3.5 85 VOUT 20mV/DIV VOUT 20mV/DIV 1.5 1.0 VIN = 5V 20s/DIV VOUT = 1.2V , COUT = 4 22F 6.3V CERAMICS 0.5 0 VIN = 5V 20s/DIV VOUT = 1.5V , COUT = 4 22F 6.3V CERAMICS 4604 G05 4604 G0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 VIN (V) 4604 G04 Load Transient Response Load Transient Response Load Transient Response ILOAD 2A/DIV ILOAD 2A/DIV VOUT 20mV/DIV ILOAD 2A/DIV VOUT 20mV/DIV VOUT 20mV/DIV 20s/DIV VIN = 5V VOUT = 1.8V , COUT = 3 22F 6.3V CERAMICS 4604 G0 VIN = 5V 20s/DIV VOUT = 2.5V , COUT = 3 22F 6.3V CERAMICS 4604 G0 VIN = 5V 20s/DIV VOUT = 3.3V , COUT = 2 22F 6.3V CERAMICS 4604 G0 4604fa 4 LTM4604 LTM4604 TYPICAL PERFORMANCE CHARACTERISTICS Start-Up Start-Up VIN 2V/DIV VIN 2V/DIV IIN 1A/DIV IIN 1A/DIV 4604 G10 VIN = 5V 200s/DIV VOUT = 2.5V COUT = 4 22F NO LOAD (0.01F SOFT-START CAPACITOR) VIN = 5V 200s/DIV VOUT = 2.5V COUT = 4 22F 4A LOAD (0.01F SOFT-START CAPACITOR) VFB vs Temperature 4604 G1 Current Limit Foldback 806 1.6 1.4 804 1.2 1.0 VOUT (V) VFB (mV) 802 800 0.8 0.6 798 VOUT = 1.5V VIN = 5V 0.2 VIN = 3.3V VIN = 2.5V 0 4 5 3 0.4 796 794 -50 -25 0 25 50 TEMPERATURE (°C) 75 100 7 6 OUTPUT CURRENT (A) 8 4604 G13 4604 G12 Short-Circuit Protection 1.5V Short, No Load Short-Circuit Protection 1.5V Short, 4A Load VOUT 0.5V/DIV VOUT 0.5V/DIV IIN 4A/DIV IIN 1A/DIV VIN = 5V 20s/DIV 4604 G14 VIN = 5V 100s/DIV 4604 G15 4604fa 5 LTM4604 LTM4604 PIN FUNCTIONS VIN (B1, C1, C3-C7, D7, E6 and E7): Power Input Pins. Apply input voltage between these pins and GND pins. Recommend placing input decoupling capacitance directly between VIN pins and GND pins. resistor. Different output voltages can be programmed with an additional resistor between FB and GND pins. Two power modules can current share when this pin is connected in parallel with the adjacent module's FB pin. See Applications Information section. VOUT (D8-D11 D8-D11, E8-E11 E8-E11, F6-F11 F6-F11, G6-G11 G6-G11): Power Output Pins. Apply output load between these pins and GND pins. Recommend placing output decoupling capacitance directly between these pins and GND pins. Review Table 4. COMP (G1): Current Control Threshold and Error Amplifier Compensation Point. The current comparator threshold increases with this control voltage. Two power modules can current share when this pin is connected in parallel with the adjacent module's COMP pin. GND (G3-G5, F3-F5, E4-E5, A1-A11 A1-A11, B6-B11 B6-B11, C8-C11 C8-C11): Power Ground Pins for Both Input and Output Returns. PGOOD (F1): Output Voltage Power Good Indicator. Opendrain logic output that is pulled to ground when the output voltage is not within ±7.5% of the regulation point. TRACK (E1): Output Voltage Tracking Pin. When the module is configured as a master output, then a soft-start capacitor is placed on the RUN/SS pin to ground to control the master ramp rate. Slave operation is performed by putting a resistor divider from the master output to ground, and connecting the center point of the divider to this pin on the slave regulator. If tracking is not desired, then connect the TRACK pin to VIN. Load current must be present for tracking. See Applications Information section. RUN/SS (D1): Run Control and Soft-Start Pin. A voltage above 0.8V will turn on the module, and below 0.5V will turn off the module. This pin has a 1M resistor to VIN and a 1000pF capacitor to GND. See Application Information section for soft-start information. SW (B3 and B4): Switching Node of the circuit is used for testing purposes. This can be connected to copper on the board to improve thermal performance. Make sure not to connect it to other output pins. FB (G2): The Negative Input of the Error Amplifier. Internally, this pin is connected to VOUT with a 4.99k precision TOP VIEW TRACK A B PGOOD C F D E G VIN COMP 1 2 SW 3 RUN/ SS FB GND 4 5 6 7 8 9 10 11 GND VOUT 4604fa 6 LTM4604 LTM4604 BLOCK DIAGRAM VIN PGOOD RSS 1M RUN/SS CSSEXT 10F 6.3V 2 10F 6.3V VIN 2.375V TO 5.5V CSS 1000pF M1 TRACK SUPPLY 4.99k TRACK 5.76k L CONTROL, DRIVE C2 470pF M2 COMP VOUT R1 4.99k 0.5% 22F 6.3V 3 10F 6.3V INTERNAL COMP VOUT 1.5V 4A GND 4604 BD FB RFB 5.76k SW Figure 1. Simplified LTM4604 LTM4604 Block Diagram DECOUPLING REQUIREMENTS TA = 25°C. Use Figure 1 Configuration. SYMBOL PARAMETER CONDITIONS MIN CIN External Input Capacitor Requirement (VIN = 2.375V to 5.5V, VOUT = 1.5V) IOUT = 4A 10 COUT External Output Capacitor Requirement (VIN = 2.375V to 5.5V, VOUT = 1.5V) IOUT = 4A 22 TYP MAX UNITS F 100 F 4604fa 7 LTM4604 LTM4604 OPERATION Power Module Description The LTM4604 LTM4604 is a standalone non-isolated switch mode DC/DC power supply. It can deliver up to 4A of DC output current with few external input and output capacitors. This module provides a precise regulated output voltage programmable via one external resistor from 0.8V DC to 5.0V DC over a 2.375V to 5.5V input voltage. A typical application schematic is shown in Figure 15. The LTM4604 LTM4604 has an integrated constant frequency current mode regulator with built-in power MOSFETs with fast switching speed. The typical switching frequency is 1.25MHz. With current mode control and internal feedback loop compensation, the LTM4604 LTM4604 module has sufficient stability margins and good transient performance under a wide range of operating conditions and with a wide range of output capacitors, even all ceramic output capacitors. Current mode control provides cycle-by-cycle fast current limit. In addition, foldback current limiting is provided in an overcurrent condition while VOUT drops. Internal overvoltage and undervoltage comparators pull the open- drain PGOOD output low if the output feedback voltage exits a ±7.5% window around the regulation point. Furthermore, in an overvoltage condition, internal top FET M1 is turned off and bottom FET M2 is turned on and held on until the overvoltage condition clears. Pulling the RUN pin below 0.5V forces the controller into its shutdown state, turning off both M1 and M2. At low load current, the module works in continuous current mode by default to achieve minimum output voltage ripple. The TRACK pin is used for power supply tracking. See the Applications Information section. The LTM4604 LTM4604 is internally compensated to be stable over a wide operating range. Table 4 provides a guideline for input and output capacitance for several operating conditions. An excel loop analysis tool is provided for transient and stability analysis. The FB pin is used to program the output voltage with a single resistor connected to ground. 4604fa 8 LTM4604 LTM4604 APPLICATIONS INFORMATION A typical LTM4604 LTM4604 application circuit is shown in Figure 15. External component selection is primarily determined by the maximum load current and output voltage. Refer to Table 4 for specific external capacitor requirements for a particular application. Without considering the inductor current ripple, the RMS current of the input capacitor can be estimated as: VIN to VOUT Step-Down Ratios In the above equation, % is the estimated efficiency of the power module. The bulk capacitor can be a switcherrated electrolytic aluminum capacitor, OS-CON capacitor for bulk input capacitance due to high inductance traces or leads. If a low inductance plane is used to power the device, then no input capacitance is required. The two internal 10F ceramics are typically rated for 2A to 3A of RMS ripple current. The worst-case ripple current for the 4A maximum current is 2A or less. There are restrictions in the maximum VIN and VOUT stepdown ratio that can be achieved for a given input voltage. The LTM4604 LTM4604 is 100% duty cycle, but the VIN to VOUT minimum dropout is a function of the load current. A typical 0.5V minimum is sufficient (see Typical Performance Characteristics). Output Voltage Programming The PWM controller has an internal 0.8V reference voltage. As shown in the Block Diagram, a 4.99k, 0.5% internal feedback resistor connects the VOUT and FB pins together. The output voltage will default to 0.8V with no feedback resistor. Adding a resistor RFB from the FB pin to GND programs the output voltage: VOUT = 0.8 V · 4.99k + RFB RFB Table 1. FB Resistor vs Output Voltage VOUT 0.8V 1.2V 1.5V 1.8V 2.5V 3.3V RFB Open 10k 5.76k 4.02k 2.37k 1.62k Input Capacitors The LTM4604 LTM4604 module should be connected to a low acimpedance DC source. Two 10F ceramic capacitors are included inside the module. Additional input capacitors are only needed if a large load step is required up to a full 4A level. An input 47F bulk capacitor is only needed if the input source impedance is compromised by long inductive leads or traces. For a buck converter, the switching duty cycle can be estimated as: D= VOUT VIN ICIN(RMS) = IOUT(MAX ) % · D · (1 ­ D) Output Capacitors The LTM4604 LTM4604 is designed for low output voltage ripple. The bulk output capacitors defined as COUT are chosen with low enough effective series resistance (ESR) to meet the output voltage ripple and transient requirements. COUT can be a low ESR tantalum capacitor, a low ESR polymer capacitor or an X5R/X7R ceramic capacitor. The typical output capacitance range is 22F to 100F Additional . output filtering may be required by the system designer if further reduction of output ripple or dynamic transient spike is required. Table 4 shows a matrix of different output voltages and output capacitors to minimize the voltage droop and overshoot during a 2A/s transient. The table optimizes the total equivalent ESR and total bulk capacitance to maximize transient performance. The Linear Technology Module Power Design Tool can be provided for further optimization. Fault Conditions: Current Limit and Overcurrent Foldback The LTM4604 LTM4604 has current mode control, which inherently limits the cycle-by-cycle inductor current not only in steady-state operation, but also in transient. To further limit current in the event of an overload condition, the LTM4604 LTM4604 provides foldback current limiting as the output voltage falls. The LTM4604 LTM4604 device has overtemperature shutdown protection that inhibits switching operation around 150°C. 4604fa 9 LTM4604 LTM4604 APPLICATIONS INFORMATION Run Enable and Soft-Start The RUN/SS pin provides dual functions of enable and soft-start control. The RUN/SS pin is used to control turn on of the LTM4604 LTM4604. While this pin is below 0.5V, the LTM4604 LTM4604 will be in a 7A low quiescent current state. A 0.8V threshold will enable the LTM4604 LTM4604. This pin can be used to sequence LTM4604 LTM4604 devices. The soft-start control is provided by a 1M pull-up resistor (RSS) and a 1000pF capacitor (CSS) as drawn in the Block Diagram. An external capacitor can be applied to the RUN/SS pin to increase the soft-start time. A typical value is 0.01F The approximate . equation for soft-start is: VIN t SOFTSTART = ln · RSS (CSS + CSSEXT ) VIN ­ 1.8 V where RSS and CSS are shown in the Block Diagram of Figure 1, 1.8V is the soft-start upper range, and CSSEXT is the additional capacitance for further soft-start control. The soft-start function can also be used to control the output ramp-up time, so that another regulator can be easily tracked. An independent ramp control signal can be applied to the master ramp, otherwise, connect the TRACK pin to VIN to disable tracking. VIN 5V CIN1 10F 6.3V X5R OR X7R VIN PGOOD LTM4604 LTM4604 COMP VTRACK = RFB2 ·V 4.99k + RFB2 MASTER VTRACK is the track ramp applied to the slave's TRACK pin. VTRACK applies the track reference for the slave output up to the point of the programmed value at which VTRACK proceeds beyond the 0.8V reference value. The VTRACK pin must go beyond 0.8V to ensure the slave output has reached its final value. Load current must be present for proper tracking. 10 FB RUN/SS TRACK GND CSSEXT RAMP CONTROL OR VIN RFB3 1.62k COUT1 22F 6.3V 3 X5R OR X7R VMASTER 3.3V 4A VIN 5V CIN2 10F 6.3V X5R OR X7R VIN PGOOD VOUT LTM4604 LTM4604 COMP FB RUN/SS TRACK GND RFB 5.76k RFB2 5.76k COUT2 22F 6.3V 3 X5R OR X7R VSLAVE 1.5V 4A RFB1 4.99k 4604 F02 Output Voltage Tracking Figure 2 MASTER OUTPUT OUTPUT VOLTAGE (V) Output voltage tracking can be programmed externally using the TRACK pin. The output can be tracked up and down with another regulator. The master regulator's output is divided down with an external resistor divider that is the same as the slave regulator's feedback divider to implement coincident tracking. The LTM4604 LTM4604 uses a very accurate 4.99k resistor for the top feedback resistor. Figure 2 shows an example of coincident tracking. VOUT SLAVE OUTPUT TIME 4604 F03 Figure 3 4604fa LTM4604 LTM4604 APPLICATIONS INFORMATION Ratio metric modes of tracking can be achieved by selecting different resistor values to change the output tracking ratio. The master output must be greater than the slave output for the tracking to work. Linear Technology Tracker Cad26 can be used to implement different tracking scenarios. The Master and Slave data inputs can be used to implement the correct resistor values for coincident or ratio tracking. The master and slave regulators require load current for tracking down. Parallel Operation The LTM4604 LTM4604 device is an inherently current mode controlled device. Parallel modules will have very good current sharing. This will balance the thermals on the design. Figure 16 shows a schematic of the parallel design. The voltage feedback changes with the variable N as more modules are paralleled. The equation: VOUT Power Good The PGOOD pin is an open-drain pin that can be used to monitor valid output voltage regulation. This pin monitors a ±7.5% window around the regulation point. COMP Pin The pin is the external compensation pin. The module has already been internally compensated for all output voltages. Table 4 is provided for most application requirements. A spice model will be provided for other control loop optimizations. 4.99k + RFB = 0.8 V · N RFB N is the number of paralleled modules. Thermal Considerations and Output Current Derating The power loss curves in Figures 4 and 5 can be used in coordination with the load derating curves in Figures 6 through 13 for calculating an approximate JA for the module with and without heat sinking methods with various airflow conditions. Thermal models are derived from several temperature measurements at the bench, and are correlated with thermal analysis software. Tables 2 and 3 provide a summary of the equivalent JA for the noted conditions. These equivalent JA parameters are correlated to the measured values and improve with air flow. The maximum junction temperature is monitored while the derating curves are derived. 1.8 1.6 1.6 1.4 1.4 1.2 1.2 WATTS 2.0 1.8 WATTS 2.0 1.0 0.8 1.0 0.8 0.6 0.6 5V TO 1.2V POWER LOSS 3.3V TO 1.2V POWER LOSS 0.4 0.2 0 0 1 3 2 LOAD CURRENT (A) 4 0.2 5 4604 F04 Figure 4. 1.2V Power Loss 5V TO 2.5V POWER LOSS 3.3V TO 2.5V POWER LOSS 0.4 0 0 1 2 3 LOAD CURRENT (A) 4 5 4604 F05 Figure 5. 2.5V Power Loss 4604fa 11 LTM4604 LTM4604 APPLICATIONS INFORMATION 3.5 3.0 3.0 LOAD CURRENT (A) 4.0 3.5 LOAD CURRENT (A) 4.0 2.5 2.0 1.5 1.0 2.0 1.5 1.0 0LFM 200LFM 200LFM 400LFM 400LFM 0.5 0 2.5 70 0 80 85 90 95 100 105 110 115 AMBIENT TEMPERATURE (°C) 75 0LFM 200LFM 200LFM 400LFM 400LFM 0.5 70 75 80 85 90 95 100 105 110 115 AMBIENT TEMPERATURE (°C) 4606 F06 4606 F07 4.0 3.5 3.5 3.0 3.0 LOAD CURRENT (A) Figure 7. 5VIN to 1.2VOUT with Heat Sink 4.0 LOAD CURRENT (A) Figure 6. 5VIN to 1.2VOUT No Heat Sink 2.5 2.0 1.5 2.0 1.5 1.0 1.0 0LFM 200LFM 200LFM 400LFM 400LFM 0.5 0 2.5 70 75 0LFM 200LFM 200LFM 400LFM 400LFM 0.5 0 80 85 90 95 100 105 110 115 AMBIENT TEMPERATURE (°C) 70 75 80 85 90 95 100 105 110 115 AMBIENT TEMPERATURE (°C) 4606 F09 4606 F08 Figure 8. 3.3VIN to 1.2VOUT No Heat Sink Figure 9. 3.3VIN to 1.2VOUT with Heat Sink 3.5 3.0 3.0 LOAD CURRENT (A) 4.0 3.5 LOAD CURRENT (A) 4.0 2.5 2.0 1.5 1.0 2.0 1.5 1.0 0LFM 200LFM 200LFM 400LFM 400LFM 0.5 0 2.5 70 75 0LFM 200LFM 200LFM 400LFM 400LFM 0.5 80 85 90 95 100 105 110 AMBIENT TEMPERATURE (°C) 4606 F10 Figure 10. 5VIN to 2.5VOUT No Heat Sink 0 70 75 80 85 90 95 100 105 110 115 AMBIENT TEMPERATURE (°C) 4606 F11 Figure 11. 5VIN to 2.5VOUT with Heat Sink 4604fa 12 LTM4604 LTM4604 APPLICATIONS INFORMATION 3.5 3.0 3.0 LOAD CURRENT (A) 4.0 3.5 LOAD CURRENT (A) 4.0 2.5 2.0 1.5 2.0 1.5 1.0 1.0 0LFM 200LFM 200LFM 400LFM 400LFM 0.5 0 2.5 70 75 0LFM 200LFM 200LFM 400LFM 400LFM 0.5 80 85 90 95 100 105 110 115 AMBIENT TEMPERATURE (°C) 4606 F12 Figure 12. 3.3VIN to 2.5VOUT No Heat Sink 0 70 75 80 85 90 95 100 105 110 115 AMBIENT TEMPERATURE (°C) 4606 F13 Figure 13. 3.3VIN to 2.5VOUT with Heat Sink 4604fa 13 LTM4604 LTM4604 APPLICATIONS INFORMATION Table 2. 1.2V Output DERATING CURVE VIN (V) POWER LOSS CURVE AIR FLOW (LFM) HEAT SINK JA (°C/W) Figures 6, 8 3.3, 5 Figure 4 0 None 25 Figures 6, 8 3.3, 5 Figure 4 200 None 22.5 Figures 6, 8 3.3, 5 Figure 4 400 None 21 Figures 7, 9 3.3, 5 Figure 4 0 BGA Heat Sink 21 Figures 7, 9 3.3, 5 Figure 4 200 BGA Heat Sink 20 Figures 7, 9 3.3, 5 Figure 4 400 BGA Heat Sink 18 DERATING CURVE VIN (V) POWER LOSS CURVE AIR FLOW (LFM) HEAT SINK JA (°C/W) Figures 10, 12 3.3, 5 Figure 5 0 None 25 Figures 10, 12 3.3, 5 Figure 5 200 None 21 Figures 10, 12 3.3, 5 Figure 5 400 None 21 Figures 11, 13 3.3, 5 Figure 5 0 BGA Heat Sink 21 Figures 11, 13 3.3, 5 Figure 5 200 BGA Heat Sink 18 Figures 11, 13 3.3, 5 Figure 5 400 BGA Heat Sink 16 Table 3. 2.5V Output Table 4. Output Voltage Response Versus Component Matrix (Refer to Figure 17), 0A to 2A Load Step Typical Measured Values CIN VOUT (V) (CERAMIC) CIN (Bulk) COUT (CERAMIC) CCOMP VIN (V) DROOP (mV) PEAK-TOPEAK(mV) RECOVERY LOAD STEP (s) (A/s) RFB (k) 1.2 10F 56F Aluminum 100F 6.3V None 2.5 21 43 10 2 10 1.2 10F 56F Aluminum 22F ×4 None 3.3 23 45 10 2 10 1.2 10F 56F Aluminum 22F ×4 None 5 24 46 10 2 10 1.5 10F 56F Aluminum 100F 6.3V None 2.5 19 41 10 2 5.76 1.5 10F 56F Aluminum 22F ×4 None 3.3 21 43 10 2 5.76 1.5 10F 56F Aluminum 22F ×4 None 5 21 43 10 2 5.76 1.8 10F 56F Aluminum 100F 6.3V None 2.5 25 50 10 2 4.02 1.8 10F 56F Aluminum 22F ×3 None 3.3 30 60 10 2 4.02 1.8 10F 56F Aluminum 22F ×3 None 5 30 60 10 2 4.02 2.5 10F 56F Aluminum 100F 6.3V None 2.5 22 45 12 2 2.37 2.5 10F 56F Aluminum 22F ×3 None 3.3 25 55 12 2 2.37 2.5 10F 56F Aluminum 22F ×3 None 5 25 55 12 2 2.37 3.3 10F 56F Aluminum 100F 6.3V None 2.5 22 50 15 2 1.62 3.3 10F 56F Aluminum 22F ×3 None 3.3 25 56 15 2 1.62 3.3 10F 56F Aluminum 22F ×3 None 5 25 56 15 2 1.62 4604fa 14 LTM4604 LTM4604 APPLICATIONS INFORMATION Safety Considerations · Do not put vias directly on the pads unless they are capped. The LTM4604 LTM4604 modules do not provide isolation from VIN to VOUT. There is no internal fuse. If required, a slow blow fuse with a rating twice the maximum input current needs to be provided to protect each unit from catastrophic failure. · SW pads can be soldered to board to improve thermal performance. Figure 14 gives a good example of the recommended layout. For easier PC board layout and assembly due to increased spacing between land grid pads, please refer to the LTM4604A LTM4604A. Layout Checklist/Example The high integration of LTM4604 LTM4604 makes the PCB board layout very simple and easy. However, to optimize its electrical and thermal performance, some layout considerations are still necessary. GND VOUT COUT · Use large PCB copper areas for high current path, including VIN, GND and VOUT. It helps to minimize the PCB conduction loss and thermal stress. COUT COUT · · Place high frequency ceramic input and output capacitors next to the VIN, GND and VOUT pins to minimize high frequency noise. · · · · VIN · Place a dedicated power ground layer underneath the unit. · · · · · To minimize the via conduction loss and reduce module thermal stress, use multiple vias for interconnection between top layer and other power layers. CIN · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · SW · · · · · · · · · · GND · · 4604 F14 Figure 14. Recommended PCB Layout VIN 2.375V TO 5.5V CIN 10F 6.3V X5R OR X7R OPEN-DRAIN PULL UP VIN PGOOD VOUT 1.5V 4A VOUT LTM4604 LTM4604 COMP FB RUN/SS TRACK CSSEXT 0.01F GND RFB 5.69k 0.5% COUT 22F 3 6.3V X5R OR X7R REFER TO TABLE 4 4604 F15 Figure 15. Typical 2.375V to 5.5V Input, 1.5V at 4A Design 4604fa 15 LTM4604 LTM4604 TYPICAL APPLICATIONS VIN 2.375V TO 5V CIN1 10F 6.3V X5R OR X7R OPEN-DRAIN PULL UP VOUT = 0.8V (4.99k/N) + RFB)/RFB WHERE N IS THE NUMBER OF PARALLEL DEVICES VIN PGOOD VOUT COUT1 22F 3 6.3V X5R OR X7R REFER TO TABLE 4 LTM4604 LTM4604 COMP FB RUN/SS TRACK CSSEXT 0.01F RFB 2.87k GND VOUT 1.5V 8A CIN2 10F 6.3V X5R OR X7R VIN PGOOD VOUT COUT2 22F 3 6.3V X5R OR X7R REFER TO TABLE 4 LTM4604 LTM4604 COMP FB RUN/SS TRACK GND 4604 F16 Figure 16. Two LTM4604s in Parallel, 1.5V at 8A Design. Also See the 8A LTM4608A LTM4608A or Dual 4A per Channel LTM4614 LTM4614 VIN 3.3V TO 5V CIN 10F 6.3V X5R OR X7R 50k VIN OPEN-DRAIN PULL UP PGOOD VOUT 2.5V 4A VOUT LTM4604 LTM4604 COMP FB RUN/SS TRACK CSSEXT 0.01F GND RFB 2.37k COUT 22F 3 6.3V X5R OR X7R REFER TO TABLE 4 4604 F17 Figure 17. 3.3V to 5V Input, 2.5V at 4A Design 4604fa 16 3.810 2.540 1.270 0.4445 0.000 0.4445 1.270 2.540 SUGGESTED PCB LAYOUT TOP VIEW 1.270 PACKAGE TOP VIEW 0.4445 0.000 0.4445 5.080 X 9.00 BSC Y aaa Z 1.90 ­ 2.10 DETAIL A MOLD CAP Z 0.29 ­ 0.35 SUBSTRATE LAND DESIGNATION PER JESD MO-222 MO-222 4 SYMBOL TOLERANCE 0.15 aaa 0.10 bbb 6. THE TOTAL NUMBER OF PADS: 66 5. PRIMARY DATUM -Z- IS SEATING PLANE DETAILS OF PAD #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE PAD #1 IDENTIFIER MAY BE EITHER A MOLD OR A MARKED FEATURE 3 2. ALL DIMENSIONS ARE IN MILLIMETERS TRAY PIN 1 BEVEL COMPONENT PIN "A1" 3 PADS SEE NOTES 1.27 BSC 0.864 ­ 0.914 7.620 BSC NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994 5M-1994 DETAIL A PACKAGE SIDE VIEW 2.19 ­ 2.45 (Reference LTC DWG # 05-08-1807 Rev A) bbb Z aaa Z 3.810 4 1.270 PAD "A1" CORNER 6.350 15.00 BSC 6.350 5.080 3.810 2.540 2.540 3.810 LGA Package 66-Lead (15mm × 9mm × 2.32mm) 11 10 8 7 6 5 PACKAGE BOTTOM VIEW 4 3 LGA 66 0607 REV A PACKAGE IN TRAY LOADING ORIENTATION LTMXXXXXX mModule 9 12.70 BSC 0.864 ­ 0.914 2 1 PAD 1 A B C D E F G LTM4604 LTM4604 PACKAGE DESCRIPTION 4604fa 17 LTM4604 LTM4604 PACKAGE DESCRIPTION Pin Assignment Table (Arranged by Pin Number) PIN NAME PIN NAME PIN NAME PIN NAME PIN NAME PIN NAME PIN NAME A1 GND B1 VIN C1 VIN D1 RUN/SS E1 TRACK F1 PGOOD G1 COMP A2 GND B2 ­ C2 ­ D2 ­ E2 ­ F2 ­ G2 FB A3 GND B3 SW C3 VIN D3 ­ E3 ­ F3 GND G3 GND A4 GND B4 SW C4 VIN D4 ­ E4 GND F4 GND G4 GND A5 GND B5 ­ C5 VIN D5 ­ E5 GND F5 GND G5 GND A6 GND B6 GND C6 VIN D6 ­ E6 VIN F6 VOUT G6 VOUT A7 GND B7 GND C7 VIN D7 VIN E7 VIN F7 VOUT G7 VOUT A8 GND B8 GND C8 GND D8 VOUT E8 VOUT F8 VOUT G8 VOUT A9 GND B9 GND C9 GND D9 VOUT E9 VOUT F9 VOUT G9 VOUT A10 GND B10 GND C10 GND D10 VOUT E10 VOUT F10 VOUT G10 VOUT A11 GND B11 GND C11 GND D11 VOUT E11 VOUT F11 VOUT G11 VOUT 4604fa 18 LTM4604 LTM4604 REVISION HISTORY REV DATE DESCRIPTION PAGE NUMBER A 5/10 Updated Front Page Text 1 Updated Absolute Maximum Ratings and Pin Configuration Section 2 Updated Callouts on Graphs 5 Added text to Layout Checklist/Example Section 15 Updated Figure 16 Title 15 4604fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 19 LTM4604 LTM4604 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC2900 LTC2900 Quad Supply Monitor with Adjustable Reset Timer Monitors Four Supplies; Adjustable Reset Timer LTC2923 LTC2923 Power Supply Tracking Controller Tracks Both Up and Down; Power Supply Sequencing LTM4600 LTM4600 10A DC/DC Module Basic 10A DC/DC Module LTM4601 LTM4601 12A DC/DC Module with PLL, Output Tracking/ Margining and Remote Sensing Synchronizable, PolyPhase Operation, LTM4601-1 LTM4601-1 Version has no Remote Sensing LTM4602 LTM4602 6A DC/DC Module Pin Compatible with the LTM4600 LTM4600 LTM4603 LTM4603 6A DC/DC Module with PLL and Output Tracking/ Margining and Remote Sensing Synchronizable, PolyPhase Operation, LTM4603-1 LTM4603-1 Version has no Remote Sensing, Pin Compatible with the LTM4601 LTM4601 LTM4608 LTM4608 8A Low Voltage Module 2.375V VIN 5V, Parallel for Higher Output Current, 9mm × 15mm × 2.8mm 4604fa 20 Linear Technology Corporation LT 0510 REV A · PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com © LINEAR TECHNOLOGY CORPORATION 2007