LT119A/LT319A LM119/LM319 LT119A LM119 LT319A LT119/319 LM319 LT119AH LM119H - Datasheet Archive

 

LM119/LM319 Dual Comparator U DESCRIPTION FEATURES s s s s s Guaranteed Maximum 0.5mV Input Offset Voltage Input Protection

 

LT119A/LT319A LT119A/LT319A LM119/LM319 LM119/LM319 Dual Comparator U DESCRIPTION FEATURES s s s s s Guaranteed Maximum 0.5mV Input Offset Voltage Input Protection Diodes Operates From Single 5V Supply 25mA Drive Capability 80ns Response Time U APPLICATIONS s s s The LT119A LT119A is capable of operation over a supply range from 5V to ±15V and can drive 25mA loads from each open collector output. A separate ground pin allows the LT119A LT119A to isolate system grounds. Linear Technology Corporation's advanced processing, design techniques and reliability make the LT119A/LT319A LT119A/LT319A an ideal choice over previous devices in most comparator applications. Window Detectors High Speed One Shot Relay/Lamp Drivers Voltage Controlled Oscillators U s The LT119A LT119A is an improved version of the LM119 LM119 dual comparator. It features lower input offset voltage and offset current, higher voltage gain, guaranteed common mode rejection, and input protection diodes. TYPICAL APPLICATION Response Time for Various Input Overdrives Window Detector* 6 5V 3 5 10 + 500 1 1/2 LT319A LT319A VIN 4 ­ TTL OUTPUT 2 OUTPUT VOLTAGE (V) VUT 2mV 4 3 5mV 20mV 2 8 + 6 1/2 LT319A LT319A VLT 9 ­ VOUT = 5.0V FOR VLT VIN VUT VOUT = 0V FOR VIN VLT OR VIN VUT 7 5 INPUT VOLTAGE (mV) 1 VS = ±15V RL = 500 V + = 5V TA = 25°C 0 100 50 0 0 LT119/319 LT119/319 TA1 50 100 150 200 250 300 350 TIME (ns) LT119/319 LT119/319 TA2 *ALLOWED WINDOW FOR SINGLE +5V SUPPLY IS 1.2V TO 3.8V 1 LT119A/LT319A LT119A/LT319A LM119/LM319 LM119/LM319 W U U W W W Supply Voltage . 36V Output to Negative Supply Voltage . 36V Ground to Negative Supply Voltage . 25V Ground to Positive Supply Voltage . 18V Differential Input Voltage (Note 5) . ± 5V Differential Input Current (Note 5) .± 5mA Input Voltage (Note 1) Output Short-Circuit Duration . 10s Operating Temperature Range LT119A LT119A, LM119 LM119 . ­ 55°C to 125°C LT319A LT319A, LM319 LM319 . 0°C to 70°C Storage Temperature Range . ­ 65°C to 150°C Lead Temperature (Soldering, 10 sec). 300°C U ABSOLUTE MAXIMUM RATINGS PACKAGE/ORDER INFORMATION TOP VIEW V+ ­INPUT 2 OUTPUT 1 10 1 9 8 +INPUT 2 GND 2 LT119AH LT119AH LM119H LM119H LT319AH LT319AH LM319H LM319H 7 GND 2 +INPUT 1 3 ­INPUT 1 ORDER PART NUMBER 4 5 V­ 6 OUTPUT 2 H PACKAGE 10-LEAD 10-LEAD TO-5 METAL CAN TJMAX = 150°C, JA = 150°C/ W, Jc = 45°C/ W TOP VIEW NC 1 NC 2 13 NC GND 3 12 OUTPUT 1 +INPUT 4 11 V + ­INPUT 5 10 ­ INPUT 2 V­ 6 9 +INPUT 2 OUTPUT 2 7 8 LT119AJ LT119AJ LM119J LM119J LT319AJ LT319AJ LM319J LM319J LT319AN LT319AN LM319N LM319N 14 NC GND 2 J PACKAGE 14-LEAD 14-LEAD CERAMIC DIP N PACKAGE 14-LEAD 14-LEAD PLASTIC DIP TJMAX = 150°C, JA = 100°C/ W (J) TJMAX = 85°C, JA = 100°C/ W (N) Consult factory for Industrial and Military grade parts. ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER VOS Input Offset Voltage VOS Input Offset Voltage (Note 2) CONDITIONS VS = ±15V, VCM = 0 (Note 3) MIN q CMRR IOS Common-Mode Rejection Ratio Input Offset Current 90 (Note 3) q IB Input Bias Current (Note 3) q AV VSAT Voltage Gain Response Time Saturation Voltage Output Leakage Current 20 (Note 4) VIN ­5mV, IO = 25mA V+ 4.5V, V ­ = 0V VIN ­6mA, ISINK 3.2mA TA 0°C TA 0°C VIN 5mV, VOUT = 35V 0.23 q Input Voltage Range 2 VS = ±15V V+ = 5V, V ­ = 0V LT119A LT119A TYP MAX 0.3 0.5 0.5 1.0 1.2 2.0 106 20 40 75 150 500 1000 40 80 0.75 1.5 q q ­12 1 0.2 1 ±13 0.4 0.6 2 10 12 3 MIN LT119 LT119 TYP 0.7 30 150 10 40 80 0.75 0.23 ­12 1 0.2 1 ±13 MAX 4 4 7 1.5 UNITS mV mV mV dB nA nA nA nA V/mV ns V 0.4 0.6 2 10 12 3 V V µA µA V V 75 100 500 1000 LT119A/LT319A LT119A/LT319A LM119/LM319 LM119/LM319 ELECTRICAL CHARACTERISTICS SYMBOL PARAMETER Differential Input Voltage IS Supply Current IS Positive Supply Current IS Negative Supply Current VOS Input Offset Voltage VOS Input Offset Voltage CMRR IOS Common-Mode Rejection Ratio Input Offset Current (Note 2) CONDITIONS MIN q V + = 5V, V ­ = 0V VS = ±15V VS = ±15V VS = ±15V, VCM = 0V RS 5k (Note 3) q 90 (Note 3) q IB Input Bias Current (Note 3) q AV VSAT Voltage Gain Response Time Saturation Voltage Output Leakage Current Input Voltage Range IS IS IS Differential Input Voltage Supply Current Positive Supply Current Negative Supply Current 20 (Note 4) VIN ­10mV, ISINK = 25mA TA = 25°C V+ 4.5V, V­ = 0V VIN ­10mV, ISINK 3.2mA VIN 10mV, VOUT = 35V VS = ±15V V+ = 5V, V ­ = 0V LT119A LT119A TYP MAX ±5 4.3 8 11.5 3 4.5 0.3 0.5 0.5 1 2 106 30 40 60 150 500 1000 40 80 The q denotes specifications which apply over the full operating temperature range. Note 1: For supply voltages less than ±15V, the maximum input voltage is equal to the supply voltage. Note 2: Unless otherwise noted, supply voltage equals ±15V and TA = 25°C. The ground pin is grounded. Note that the maximum voltage allowed between the ground pin and V + is 18V. Do not tie the ground pin to V ­ when the power supply voltage exceeds ±9V. The offset voltage, offset current and bias current specifications apply for all supply voltages between ±15V and 5V unless otherwise specified. LT119 LT119 TYP 4.3 8 3 2 80 250 8 MAX ±5 11.5 4.5 8 8 10 200 300 1000 1200 40 80 UNITS V mA mA mA mV mV mV dB nA nA nA nA V/mV ns 0.75 q q 0.75 1.5 V 0.3 0.2 ±13 q 1.5 0.4 10 0.3 0.2 ±13 0.4 10 V µA V V V mA mA mA 1 3 ±5 q V+ = 5V, V ­ = 0V VS = ±15V VS = ±15V MIN 4.3 8 3 12.5 5 1 3 ±5 4.3 8 3 12.5 5 Note 3: The offset voltages and currents given are the maximum values required to drive the output within 1V of either supply with a 1mA load, thus these parameters define an error band and take into account the worst case effects of voltage gain and input impedance. Note 4: Response time specified is for a 100mV input step with 5mV overdrive. Note 5: Inputs are protected with back-to-back 5.6V zener diodes. This limits maximum differential input voltage to ±5V if current is unlimited. Larger differential input drive is allowed if input current is limited to ±5mA with external resistance. 3 LT119A/LT319A LT119A/LT319A LM119/LM319 LM119/LM319 U W TYPICAL PERFORMANCE CHARACTERISTICS Transfer Function 40 V + + = 5V 25 5 20 4 15 3 10 2 5.0 300 200 200 1 0 ­1.0 ­0.6 0.2 0.6 ­0.2 DIFFERENTIAL INPUT VOLTAGE (mV) 100 0 ­6 2 6 ­2 DIFFERENTIAL INPUT VOLTAGE (V) 5mV 2 5 20mV 6 5 2mV 4 3 2 0 0 ­50 ­100 0 50 VS = 5V RL = 500 V + = 5V TA = 25°C 100 50 0 100 150 200 250 300 350 TIME (ns) 0 50 100 150 200 250 300 350 TIME (ns) LT119/319 LT119/319 G4 Output Saturation Voltage ­100 50 100 150 200 250 300 350 TIME (ns) Output Limiting Characteristics 1.2 TJ = 25°C 5 POSITIVE SUPPLY 6 4 NEGATIVE SUPPLY 2 VS = ±15V INPUT OVERDRIVE = 5mV 0 0.6 0.8 0.4 OUTPUT VOLTAGE (V) SHORT-CIRCUIT CURRENT (mA) SUPPLY CURRENT (mA) 10 8 1.0 LT119/319 LT119/319 G7 0 15 5 10 SUPPLY VOLTAGE (V) 20 LT119/319 LT119/319 G8 1.0 100 SHORT-CIRCUIT CURRENT AFTER 3 MINUTES 80 0.8 60 0.6 40 0.4 POWER DISSIPATION 20 0 0.2 0 5 10 OUTPUT VOLTAGE (V) 15 LT119/319 LT119/319 G9 0 POWER DISSIPATION (W) OUTPUT CURRENT (mA) 0 120 10 15 2mV ­50 TJ = 25°C 20 4 5mV 0 0 Supply Current TJ = 25°C 0.2 20mV 2 LT119/319 LT119/319 G6 12 0 4 3 LT119/319 LT119/319 G5 25 0 VS = 5V RL = 500 V + = 5V TA = 25°C 1 INPUT VOLTAGE (mV) 0 5mV 20mV 1 INPUT VOLTAGE (mV) 1 INPUT VOLTAGE (mV) OUTPUT VOLTAGE (V) 4 3 Response Time for Various Input Overdrives 6 VS = ±15V RL = 500 V + = 5V TA = 25°C 5 25 45 65 85 105 125 TEMPERATURE (°C) LT119/319 LT119/319 G3 Response Time for Various Input Overdrives OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 2mV 0 ­ 55 ­35 ­15 10 LT119/319 LT119/319 G2 Response Time for Various Input Overdrives 5 100 OFFSET LT119/319 LT119/319 G1 6 BIAS 150 50 MAXIMUM DIFFERENTIAL INPUT VOLTAGE ­100 ­10 0 1.0 VS = ±15V INPUT CURRENT (nA) 6 250 VS = ±15V TA = 25°C 7 INPUT BIAS CURRENT (nA) 30 Input Currents 400 OUTPUT VOLTAGE LOW (V) OUTPUT VOLTAGE HIGH (V) V + + = 36V VS = ±15V RL = 1.4k TA = 25°C 35 Input Characteristics 8 LT119A/LT319A LT119A/LT319A LM119/LM319 LM119/LM319 U W TYPICAL PERFORMANCE CHARACTERISTICS Common-Mode Limits Supply Current V+ 12 V + = 5V, V ­ = 0V ­0.8 10 SUPPLY CURRENT (mA) COMMON-MODE LIMITS (V) ­0.4 VS = ±15V ­1.2 ­1.6 REFERRED TO SUPPLY VOLTAGES ­2.0 1.2 0.8 + ­ VS = ±15V, V = 5V, V = 0V POSITIVE SUPPLY = 15V 8 6 POSITIVE SUPPLY = 5V, V ­ = 0V 4 2 NEGATIVE SUPPLY = ­15V 0.4 V­ ­ 55 ­ 35 ­15 0 ­ 55 ­ 35 ­15 5 25 45 65 85 105 125 TEMPERATURE (°C) 5 25 45 65 85 105 125 TEMPERATURE (°C) LT119/319 LT119/319 G11 LT119/319 LT119/319 G10 U TYPICAL APPLICATIONS High Noise Immunity 60Hz Sync Circuit Relay Driver 5V 28V 5V 68k 9 10 ­ 8 60Hz INPUT 10VP­P (TYP) 6 1/2 LT319A LT319A INPUTS 7 + 1N4148 1N4148 3.3k 20k 9 0.15µF 35V 5 ­ 10 1/2 LT319A LT319A 8 + 6 OUTPUT 7 5 10k LT119/319 LT119/319 TA3 Voltage Controlled Crystal Oscillator With 100PPM 100PPM Trim Range INPUT 0V TO 5V 100k 10k LT119/319 LT119/319 TA4 AT CUT 18pF, 100kHz 10k 5V MV1405 MV1405* 4 1000pF 1/2 LT319A LT319A 3 5V 10 1k ­ 1 8 + 1k + 6 1/2 LT319A LT319A 9 2 39k 20k OUTPUT 7 ­ 5 3k 20k 5V 2k LT119/319 LT119/319 TA5 5 LT119A/LT319A LT119A/LT319A LM119/LM319 LM119/LM319 U TYPICAL APPLICATIONS Voltage Controlled High Speed One Shot 5V 100pF 9 10 ­ 680 6 1/2 LT319A LT319A 2k 8 5V INPUT PULSE + 7408 2 5V OUTPUT 0µs TO 1µs (20ns MINIMUM) 10k 100pF 1k 3 2k 120pF 4 680 + 1 1/2 LT319A LT319A 7 ­ 0V TO 1V INPUT 300pF 5 LT119/319 LT119/319 TA6 LM385-1 LM385-1.2 5V 10-Bit Serial Output A/D Converter 5V INPUT 0V TO 3.5V 5V 10k* 20k* LT1004-1 LT1004-1.2 4.7k 10k PN4250 PN4250 4 PN4250 PN4250 5V 10 ­ 1 1/2 LT119A LT119A 3 1N4148 1N4148 8 2 + 1000µF 9 5 ­5V 74C04 74C04 1k + 1/2 LT119A LT119A ­ 6 DATA OUT 7 1N4148 1N4148 39k 82k 0.1µF 2N3904 2N3904 1N4148 1N4148 1k 3.9k 15k 1k CONVERT COMMAND INPUT (TTL) *1% FILM ­5V POLYSTYRENE, MOUNT CAPACITORS CLOSE TOGETHER CONVERSION TIME = 10ms * = 1% CAPACITORS ARE POLYSTYRENE MOUNT IN CLOSE PROXIMITY 5V LT119/319 LT119/319 TA7 5 Microsecond Sample-and-Hold with Zero Hold Step 15V + 10µF 1N4148 1N4148 4.7k 100 3k 2N2907 2N2907 240 15V 2N2907 2N2907 2N4931 2N4931 15V 10 12k 0.003µF 10k 1 2N2907 2N2907 3k 2N2222 2N2222 VOUT ­ 20k 3 3.3k 9k 1/2 LT119A LT119A 2 + ­15V 4 1k ­ 6 8 7 + 9k 15V 3k 1N4148 1N4148 ­15V 6 9 1/2 LT119A LT119A 1k 5 INPUT *TRIM FOR ZERO VOLTS OUT WITH ZERO VOLTS IN POLYSTYRENE CAPACITOR 2pF TO 8pF* 10pF Q VS CLK D 74C74 74C74 CLR PRESET 5V 0V SAMPLE HOLD LT119/319 LT119/319 TA8 LT119A/LT319A LT119A/LT319A LM119/LM319 LM119/LM319 U TYPICAL APPLICATIONS 5kHz to 2MHz VF Converter 5V 50pF POLYSTYRENE 3.3k 5V 5V 330 TTL OUT 5kHz TO 2MHz 470 10k 2k 20k 4 0V TO 10V 0.01µF 3 2N2369 2N2369 ­ 1/2 LT119A LT119A + 470 1 22pF 2 10k 220 1M 5V 10k 2k 10 LT1004-1 LT1004-1.2 ­ ­5V 6 1/2 LT119A LT119A + 7 ALL DIODES 1N4148 1N4148 SET SCALE FACTOR 9 0.1µF 8 5 3k LT119/319 LT119/319 TA9 ­5V W W SCHEMATIC DIAGRAM R1 3.5k R2 4k V+ R3 4k R6 3k R7 3k Q9 Q4 Q8 Q3 ­ + C1 18pF Q6 Q2 R4 3k 5.6V INPUTS Q7 R11 13k R5 3k R12 13k R10 170 5.6V Q15 R8 2k Q1 Q5 Q13 R9 18k Q22 R23 4k R22 60 R20 3.6k R18 1.9k Q11 R25 600 R24 250 R19 250 Q20 OUTPUT Q14 R13 600 Q16 Q12 Q21 TO OTHER SIDE LT119A LT119A R15 300 Q10 R16 600 R14 2k Q19 Q17 R21 Q18 900 R17 3 V­ Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. GND 7 LT119A/LT319A LT119A/LT319A LM119/LM319 LM119/LM319 U PACKAGE DESCRIPTION Dimension in inches (millimeters) unless otherwise noted. H Package 10-Lead T0-5 Metal Can 0.335 ­ 0.370 (8.509 ­ 9.398) DIA 0.305 ­ 0.335 (7.747 ­ 8.509) 0.040 (1.016) MAX 0.016 ­ 0.021 (0.406 ­ 0.533) 36°BSC 0.050 (1.270) MAX SEATING PLANE 0.027 ­ 0.034 (0.686 ­ 0.864) 0.165 ­ 0.185 (4.191 ­ 4.699) GAUGE PLANE 0.010 ­ 0.045 (0.254 ­ 1.143) 0.027 ­ 0.045 (0.686 ­ 1.143) 0.230 ( 5.842) BSC REFERENCE PLANE 0.500 ­ 0.750 (12.700 ­ 19.050) 0.110 ­ 0.160 (2.794 ­ 4.064) INSULATING STANDOFF NOTE: LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE AND SEATING PLANE. H10(5) 0592 J Package 14-Lead Ceramic DIP CORNER LEADS OPTION (4 PLCS) 0.023 ­ 0.045 (0.584 ­ 1.143) HALF LEAD OPTION 0.045 ­ 0.068 (1.143 ­ 1.727) FULL LEAD OPTION 0.785 (19.939) MAX 0.005 (0.127) MIN 14 13 12 11 10 9 8 0.220 ­ 0.310 (5.588 ­ 7.874) 0.025 (0.635) RAD TYP 1 2 3 4 5 6 7 0.200 (5.080) MAX 0.300 BSC (0.762 BSC) 0.015 ­ 0.060 (0.381 ­ 1.524) 0.008 ­ 0.018 (0.203 ­ 0.457) 0° ­ 15° 0.385 ± 0.025 (9.779 ± 0.635) 0.045 ­ 0.068 (1.143 ­ 1.727) 0.100 ± 0.010 (2.540 ± 0.254) 0.125 (3.175) MIN 0.014 ­ 0.026 (0.360 ­ 0.660) J14 0594 NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP OR TIN PLATE LEADS. N Package 14-Lead Plastic DIP 0.300 ­ 0.325 (7.620 ­ 8.255) 0.045 ­ 0.065 (1.143 ­ 1.651) 0.130 ± 0.005 (3.302 ± 0.127) 0.015 (0.380) MIN ( +0.635 8.255 ­0.381 ) 14 13 12 11 10 9 8 1 2 3 4 5 6 7 0.260 ± 0.010* 0.065 (6.604 ± 0.254) (1.651) TYP 0.009 ­ 0.015 (0.229 ­ 0.381) +0.025 0.325 ­0.015 0.770* (19.558) MAX 0.125 (3.175) MIN 0.075 ± 0.015 (1.905 ± 0.381) 0.100 ± 0.010 (2.540 ± 0.254) 0.018 ± 0.003 (0.457 ± 0.076) N14 0594 *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm). 8 Linear Technology Corporation LT/GP 0694 5K REV A · PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7487 (408) 432-1900 q FAX: (408) 434-0507 q TELEX: 499-3977 © LINEAR TECHNOLOGY CORPORATION 1994