LQ121S1DG41 LD-15604 LD-15604A LD-15604B LD-15604C LD-15604D LD15604D-1

LQ121S1DG41 SPEC No. LD-15604 LD-15604A DATE JUN.20.2003 OCT.30.2003 SUMMARY PAGE 1st Issue 2 Change: 3. Mechanical technical

RECORDS OF REVISION LQ121S1DG41 LQ121S1DG41 SPEC No. LD-15604 LD-15604 LD-15604A LD-15604A DATE JUN.20.2003 OCT.30.2003 SUMMARY PAGE 1st Issue 2 Change: 3. Mechanical technical literature 3.Outline specification. 2 3. Outline specification Add: Number of colors(Number of gray scale level) 4 4-2. Backlight driving Add: Color of FL cable 5 Add: 6.Recommended operation condition 6 7-1. TFT-LCD panel driving Add: [Note6] I/F block diagram 11 10. Optical Characteristics Add: Chromaticity of Red,Green,Blue 13 12.Handling Precautions Add: h) Since there is a circuit p) Be careful of a back light 13 13.Packing form Add: Product Country TAIWAN 14 14 14 LD-15604B LD-15604B JUN.16.2004 7 11 14 LD-15604C LD-15604C JUN.28.2004 13 14 15 LD-15604D LD-15604D JUN.13.2005 NOTE 5 13 15 16 14.Reliability test items : normal operation state Add: Temperature, Humidity, Atmospheric pressure 15-1 Lot No. Label: Add: Discernment code Add: Taiwan product code 15-2 Packing box Label: Add: Taiwan product code 7-2. Backlight driving Add: It is usually required to measure Change: Lamp frequency (Min) 40kHz 35kHz 10. Optical Characteristics Response TimeRise: 15ms 10ms, Decay: 30ms 25ms 14. Reliability test items Add: ESD test Add: EMI 13. Packing form Add: Product Country CHINA 15-1 Lot No. Label: Add: China product code 15-2 Packing box Label: Add: China product code 7. Electrical Characteristics It is applied from the delivery in October, 2005. Change: Current dissipation Vcc=3.3V: 430mA(Typ.) 380mA530mA(Max.) 480mA Vcc=5.0V: 260mA(Typ.) 230mA310mA(Max.) 280mA 12.Handling Precautions Add: q) When install LCD modules 15-2 Packing box Label: Add: RoHS Compliance It is applied from the delivery in April, 2005. Fig1. OUTLINE DIMENSIONS Add: Recommended tighten torque for mounting 0.294±0.02Nm3.0±0.2kgfcm LD15604D-1 LD15604D-1 1. Application This specification applies to color TFT-LCD module, LQ121S1DG41 LQ121S1DG41 These specification sheets are the proprietary product of SHARP CORPORATION("SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. The device listed in these specification sheets was designed and manufactured for use in general electronic equipment. In case of using the device for applications such as control and safety equipment for transportation (aircraft, trains, automobiles, etc.), rescue and security equipment and various safety related equipment which require higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant system design should be taken. Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications, telecommunication equipment (trunk lines), nuclear power control equipment and medical or other equipment for life support. SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets. Contact and consult with a SHARP sales representative for any questions about this device. 2. Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a color TFT-LCD panel, driver ICs, control circuit and power supply circuit and a backlight unit. Graphics and texts can be displayed on a 800×3×600 dots panel with 262,144 colors by supplying 18 bit data signal (6bit/color), four timing signals, +3.3V/5.0V DC supply voltage for TFT-LCD panel driving and supply voltage for backlight. The TFT-LCD panel used for this module is a low-reflection and higher-color-saturation type. Therefore, this module is also suitable for the multimedia use. Viewing angle is 6 o'clock direction. This module is the type of wide viewing angle and high brightness(370cd/m2). Backlight-driving DC/AC inverter is not built in this module. LD15604D-2 LD15604D-2 3. Outline specification. Parameter Specifications Diagonal Unit Display size 31 (12.1") Active area 246.0(H)×184.5(V) mm Pixel format 800(H)×600(V) pixel (1 pixel=R+G+B dots) Number of colors (Number of gray scale level) cm - 262, 144 colors (64 gray scales per color) Pixel pitch 0.3075(H)×0.3075(V) mm Pixel configuration R,G,B vertical stripe - Display mode Normally white - Unit outline dimensions *1 276.0(W)×209.0(H)×Max.11.0 (D) Mass Max. 660 g Surface treatment Anti-glare and hard-coating 3H - *1: excluding backlight cables. Outline dimensions is shown in Fig.1 mm LD15604D-3 LD15604D-3 4. Input Terminals 4-1. TFT-LCD panel driving CN1 Corresponding connector: DF9-41S-1V DF9-41S-1V, DF9A-41S-1V DF9A-41S-1V, DF9B-41S-1V DF9B-41S-1V, DF9M-41S-1V DF9M-41S-1V Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Symbol GND CK GND Hsync Vsync GND GND GND R0 R1 R2 GND R3 R4 R5 GND GND GND G0 G1 G2 GND G3 G4 G5 GND GND GND B0 B1 B2 GND B3 B4 B5 GND ENAB R/L Vcc Vcc U/D Function Clock signal for sampling each data signal Horizontal synchronous signal Vertical synchronous signal RED data signal(LSB) RED data signal RED data signal RED data signal RED data signal RED data signal(MSB) GREEN data signal(LSB) GREEN data signal GREEN data signal GREEN data signal GREEN data signal GREEN data signal(MSB) BLUE data signal(LSB) BLUE data signal BLUE data signal BLUE data signal BLUE data signal BLUE data signal(MSB) Signal to settle the horizontal display position Horizontal display mode select signal +3.3V / +5.0V power supply +3.3V / +5.0V power supply Vertical display mode select signal (Hirose Electric Co., Ltd.) Remark [Note1] [Note1] [Note2] [Note3] [Note4] The shielding case is connected with GND. [Note1] The polarity of both synchronous signals are negative. [Note2] The horizontal display start timing is settled in accordance with a rising timing of ENAB signal. In case ENAB is fixed "Low", the horizontal start timing is determined as describedin 7-2. Don't keep ENAB "High" during operation. LD15604D-4 LD15604D-4 [Note 3],[Note 4] R/L = High, U/D = Low R/L = Low, U/D = Low R/L = High, U/D = High R/L = Low, U/D = High 4-2. Backlight driving CN2 ,CN3 Used connector : BHR-03VS-1 BHR-03VS-1(JST) Pin no. Corresponding connector :SM02(8.0)B-BHS(JST) symbol function 1 VHIGH 2 NC 3 VLOW Color of FL cable CN2 CN3 Pink Blue Power supply for lamp (High voltage side) This is electrically opened. Power supply for lamp (Low voltage side) 5. Absolute Maximum Ratings Parameter Input voltage supply voltage Storage temperature Operating temperature (Ambient) Symbol VI Vcc Tstg Topa White Condition Ta=25 oC Ta=25 oC - Ratings -0.3 to Vcc+0.3 0 to +6.0 -30 to +70 -10 to +65 [Note1] CK,R0R5,G0G5,B0B5,Hsync,Vsync,ENAB,R/L,U/D [Note2] Humidity: 95%RH Max. at Ta40 oC. Maximum wet-bulb temperature at 39 oC or less at Ta>40 oC. No condensation. Brown Unit V V o C o C Remark [Note1] [Note2] LD15604D-5 LD15604D-5 6.Recommended operation condition Parameter Symbol VI Input voltage VCC Supply voltage Ambient temperature Topa Min. 0 Typ. Max. Vcc 3.0 -10 +3.3/+5.0 Unit 5.5 +65 Remark [Note1] [Note2] [Note3] [Note1]CK,R0R5,G0G5,B0B5,Hsync,Vsync,ENAB,R/L,U/D [Note2] VCC Vcc-turn-on conditions 0