LMV710 LMV711 LMV715 SLOS463A SC-70 LMV711/LMV715 LMV710I LMV711I LMV715I - Datasheet Archive

 

SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN www.ti.com SLOS463A ­ APRIL 2005

 

LMV710 LMV710, LMV711 LMV711, LMV715 LMV715 SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN www.ti.com SLOS463A SLOS463A ­ APRIL 2005 ­ REVISED JULY 2005 FEATURES · · · · · · · · · 2.7-V and 5-V Performance Low Offset Voltage . . . 0.4 mV Typ, 3 mV Max Input Common-Mode Range . . . 200 mV Beyond the Rails Rail-to-Rail Swing Into 600 Gain Bandwidth . . . 5 MHz Typ Slew Rate . . . 5 V/µs Typ Turn-On Time From Shutdown . . . 1 M (unless otherwise noted) PARAMETER VIO Input offset voltage IIB TEST CONDITIONS Input bias current CMRR Common-mode rejection ratio kSVR Supply-voltage rejection ratio VICR Common-mode input voltage range VIC = 0.85 V and 1.85 V TYP MAX 0.4 3 3.2 25°C 4 25°C 2.7 V VCC+ 5 V, VIC = 0.85 V 50 ­40°C to 85°C 0 VIC 2.7 V 25°C 70 75 ­40°C to 85°C 110 68 Output voltage VOH RL = 600 to 1.35 V VOL 28 12 25 ­40°C to 85°C VOL 15 25°C RL = 10 k to 1.35 V ­0.3 to 3 ­40°C to 85°C VOH ­0.2 to 2.9 25°C Sinking VO = 5 V dB 95 25°C CMRR 50 dB mV dB 68 25°C 2.7 V VCC+ 5 V, VIC = 1.85 V 70 UNIT pA 45 ­40°C to 85°C Output short circuit current (1) VO MIN ­40°C to 85°C Sourcing VO = 0 IOS TA 25°C 22 25°C 2.62 ­40°C to 85°C V mA 40 2.6 25°C 2.68 0.01 ­40°C to 85°C 0.12 0.15 25°C 2.52 ­40°C to 85°C V 2.5 25°C 2.55 0.05 ­40°C to 85°C 0.23 0.3 VO(SD) Output voltage level in shutdown mode LMV711 LMV711 only 25°C 50 IO(SD) Output leakage current in shutdown mode LMV715 LMV715 only 25°C 1 pA CO(SD) Output capacitance in shutdown mode LMV715 LMV715 only 25°C 32 pF 25°C 1.22 ICC Supply current ON mode Shutdown mode, SHDN = 0 ­40°C to 85°C Large-signal voltage gain 1.7 1.9 25°C 0.002 Sourcing RL = 10 k, VO = 1.35 V to 2.3 V AV 200 25°C 80 ­40°C to 85°C 25°C 80 ­40°C to 85°C 76 25°C 80 ­40°C to 85°C 80 ­40°C to 85°C µA 76 25°C mA 76 Sinking RL = 10 k, VO = 0.4 V to 1.35 V 10 mV 76 Sourcing RL = 600 , VO = 1.35 V to 2.2 V Sinking RL = 600 , VO = 0.5 V to 1.35 V 115 113 110 dB 100 SR (2) Slew rate 25°C 5 V/µs GBWP Gain bandwidth product 25°C 5 MHz m Phase margin 25°C 60 deg T(on) Amplifier turn-on time 25°C 1 M (unless otherwise noted) PARAMETER TEST CONDITIONS TA V(ON) SHDN Shutdown pin voltage range 25°C MIN TYP 2.4 to 2.7 1.5 to 2.7 V(OFF) Vn Input referred voltage noise 0 to 1 f = 1 kHz 25°C MAX 0 to 0.8 20 UNIT V nV/Hz Electrical Characteristics VCC+ = 3.2 V, VCC­ = GND, and VIC = 1.6 V (unless otherwise noted) PARAMETER TEST CONDITIONS VOH VO Output voltage IO = 6.5 mA VOL TA MIN TYP 25°C 2.95 3 ­40°C to 85°C 2.92 25°C ­40°C to 85°C 0.01 MAX 0.18 UNIT V 0.25 5 LMV710 LMV710, LMV711 LMV711, LMV715 LMV715 SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN www.ti.com SLOS463A SLOS463A ­ APRIL 2005 ­ REVISED JULY 2005 Electrical Characteristics VCC+ = 5 V, VCC­ = GND, VIC = 2.5 V, and RL > 1 M (unless otherwise noted) PARAMETER VIO Input offset voltage IIB TEST CONDITIONS Input bias current CMRR Common-mode rejection ratio kSVR Supply-voltage rejection ratio VICR Common-mode input voltage range VIC = 0.85 V and 1.85 V TYP MAX 0.4 3 3.2 25°C 4 25°C 2.7 V VCC+ 5 V, VIC = 0.85 V 50 ­40°C to 85°C 0 VIC 2.7 V 25°C 70 75 ­40°C to 85°C 110 68 Output voltage VOH RL = 600 to 1.35 V VOL 35 21 25 ­40°C to 85°C VOL 25 25°C RL = 10 k to 1.35 V ­0.3 to 5.3 ­40°C to 85°C VOH ­0.2 to 5.2 25°C Sinking VO = 5 V dB 95 25°C CMRR 50 dB mV dB 68 25°C 2.7 V VCC+ 5 V, VIC = 1.85 V 70 UNIT pA 48 ­40°C to 85°C Output short circuit current (1) VO MIN ­40°C to 85°C Sourcing VO = 0 IOS TA 25°C 21 25°C 4.92 ­40°C to 85°C V mA 40 4.9 25°C 4.98 0.01 ­40°C to 85°C 0.12 0.15 25°C 4.82 ­40°C to 85°C V 4.8 25°C 4.85 0.05 ­40°C to 85°C 0.23 0.3 VO(SD) Output voltage level in shutdown mode LMV711 LMV711 only 25°C 50 IO(SD) Output leakage current in shutdown mode LMV715 LMV715 only 25°C 1 pA CO(SD) Output capacitance in shutdown mode LMV715 LMV715 only 25°C 32 pF 25°C 1.17 ICC Supply current ON mode Shutdown mode, SHDN = 0 ­40°C to 85°C Large-signal voltage gain 1.7 1.9 25°C 0.2 Sourcing RL = 10 k, VO = 1.35 V to 2.3 V AV 200 25°C 80 ­40°C to 85°C 25°C 80 ­40°C to 85°C 76 25°C 80 ­40°C to 85°C 80 ­40°C to 85°C µA 76 25°C mA 76 Sinking RL = 10 k, VO = 0.4 V to 1.35 V 10 mV 76 Sourcing RL = 600 , VO = 1.35 V to 2.2 V Sinking RL = 600 , VO = 0.5 V to 1.35 V 123 120 110 dB 118 SR (2) Slew rate 25°C 5 V/µs GBWP Gain bandwidth product 25°C 5 MHz m Phase margin 25°C 60 deg T(on) Amplifier turn-on time 25°C 1 M (unless otherwise noted) PARAMETER TEST CONDITIONS TA V(ON) SHDN Shutdown pin voltage range 25°C V(OFF) Vn Input referred voltage noise f = 1 kHz MIN TYP 2.4 to 5 2 to 5 0 to 1.5 25°C 20 MAX 0 to 0.8 UNIT V nV/Hz 7 LMV710 LMV710, LMV711 LMV711, LMV715 LMV715 SINGLE LOW-POWER RRIO OPERATIONAL AMPLIFIERS WITH HIGH OUTPUT CURRENT DRIVE AND SHUTDOWN SLOS463A SLOS463A ­ APRIL 2005 ­ REVISED JULY 2005 TYPICAL PERFORMANCE CHARACTERISTICS GRAPH PREVIEWS Figure 1. Supply Current vs Supply Voltage (ON Mode) Figure 2. LMV711/LMV715 LMV711/LMV715 Supply Current vs Supply Voltage (Shutdown Mode) Figure 3. Output Positive Swing vs Supply Voltage RL = 600 ) Figure 4. Output Negative Swing vs Supply Voltage RL = 600 ) Figure 5. Output Positive Swing vs Supply Voltage RL = 10 k) Figure 6. Output Negative Swing vs Supply Voltage RL = 10 k) Figure 7. Output Positive Swing vs Supply Voltage (ISRC = 7 mA) Figure 8. Output Negative Swing vs Supply Voltage (ISINK = 7 mA) Figure 9. Input Voltage Noise vs Frequency Figure 10. PSRR vs Frequency Figure 11. CMRR vs Frequency Figure 12. LMV711/LMV715 LMV711/LMV715 Turn-On Characteristics Figure 13. Sourcing Current vs Output Voltage Figure 14. Sinking Current vs Output Voltage Figure 15. THD+N vs Frequency (VCC = 5 V) Figure 16. THD+N vs Frequency (VCC = 2.7 V) Figure 17. THD+N vs VOUT (VCC± = ±2.5 V) Figure 18. THD+N vs VOUT (VCC± = ±1.35 V) Figure 19. CCM vs VCM (VCC = 2.7 V) Figure 20. CCM vs VCM (VCC = 5 V) Figure 21. CDIFF vs VCM (VCC = 2.7 V) Figure 22. CDIFF vs VCM (VCC = 5 V) Figure 23. Open-Loop Frequency Response (VCC± = ±1.35 V) Figure 24. Open-Loop Frequency Response (VCC± = ±1.6 V) Figure 25. Open-Loop Frequency Response (VCC± = ±2.5 V) Figure 26. Open-Loop Frequency Response (VCC± = ±1.35 V) Figure 27. Open-Loop Frequency Response (VCC± = ±1.6 V) Figure 28. Open-Loop Frequency Response (VCC± = ±2.5 V) Figure 29. Noninverting Large Signal Pulse Response Figure 30. Noninverting Small Signal Pulse Response Figure Figure 31. Inverting Large Signal Pulse Response Figure 32. Inverting Small Signal Pulse Response Figure 33. VOS vs VCM (VCC = 2.7 V) Figure 34. VOS vs VCM (VCC = 5 V) 8 www.ti.com PACKAGE OPTION ADDENDUM www.ti.com 5-Dec-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty LMV710IDBVR LMV710IDBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV710IDBVRE4 LMV710IDBVRE4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV710IDCKR LMV710IDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV710IDCKRE4 LMV710IDCKRE4 ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV711IDBVR LMV711IDBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV711IDBVRE4 LMV711IDBVRE4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV711IDCKR LMV711IDCKR ACTIVE SC70 DCK 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV711IDCKRE4 LMV711IDCKRE4 ACTIVE SC70 DCK 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV715IDBVR LMV715IDBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV715IDBVRE4 LMV715IDBVRE4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV715IDCKR LMV715IDCKR ACTIVE SC70 DCK 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV715IDCKRE4 LMV715IDCKRE4 ACTIVE SC70 DCK 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated