LM3S6633 LM3S6000 LM3S6633-IQC50 LM3S6633-EQC50 LM3S6633-IBZ50 LM3S6965 - Datasheet Archive

 

® LM3S6633 Microcontroller Automatic MDI/MDI-X cross-over correction Programmable MAC address 32 JTAG NVIC SWD 50 MHz 256 KB

 

® ® LM3S6633 LM3S6633 Microcontroller Automatic MDI/MDI-X cross-over correction Programmable MAC address 32 JTAG NVIC SWD 50 MHz 256 KB Flash ARM® CortexTM-M3 64 KB SRAM 32 Serial Interfaces Synchronous serial interface (SSI) with master and 3 UARTs 2 SSI/SPI Systick Timer 4 Timer/PWM/CCP Each 32-bit or 2x16-bit Watchdog Timer 2 I 2C SYSTEM SERIAL INTERFACES Clocks, Reset System Control UART GPIOs R T C Two fully programmable 16C550-type UARTs with Battery-Backed Hibernate IrDA support Timer Comparators PWM Generator PWM Interrupt Dead-Band Generator Separate 16x8 transmit (TX) and 16x12 receive (RX) LDO Voltage Regulator 3 Analog Comparators 10-bit ADC 8 channel 1 Msps FIFOs to reduce CPU interrupt service loading ANALOG MOTION CONTROL 2 Quadrature Encoder Inputs 6 PWM Outputs slave modes for SPI, MICROWIRE, or TI synchronous serial I2C interface (master and slave) Two fully programmable 16C550-type UARTs with IrDA support Temp Sensor Programmable baud-rate generator with fractional divider Analog-to-Digital Converter (ADC) Single- and differential-input configurations Three 10-bit channels (inputs) when used as single-ended inputs LM3S6000 LM3S6000 Series Block Diagram. This block diagram shows the superset of features for the LM3S6000 LM3S6000 series of microcontrollers. Sample rate of 500 thousand samples/second On-chip temperature sensor Product Features One integrated analog comparator Configurable for output to: drive an output pin, 32-Bit RISC Performance 50-MHz operation with 32-bit ARM® CortexTM-M3 architecture Thumb®-compatible Thumb-2-only instruction set, with hardware-division and single-cycle-multiplication Integrated Nested Vectored Interrupt Controller (NVIC) provides deterministic interrupt handling 27 interrupt channels with eight priority levels Memory protection unit (MPU) Unaligned data access enables data to be efficiently packed into memory Atomic bit manipulation (bit-banding) delivers maximum memory utilization and streamlined peripheral control Analog Comparators generate an interrupt, or initiate an ADC sample sequence Compare external pin input to external pin input or to internal programmable voltage reference Inter-Integrated Circuit (I2C) Interface Master and slave receive and transmit operation with transmission speed up to 100 Kbps in Standard mode and 400 Kbps in Fast mode Interrupt generation Master with arbitration and clock synchronization, multimaster support, and 7-bit addressing mode GPIOs 32 KB single-cycle SRAM 15-41 GPIOs, depending on configuration 5-V-tolerant input/outputs Programmable interrupt generation Fast toggle capable of a change every two clock cycles Can initiate an ADC sample sequence Flexible Timer Capability Power Three general-purpose timers, each configurable as On-chip Low Drop-Out (LDO) voltage regulator, with one 32-bit or two 16-bit timers Real-Time Clock (RTC) capability 24-bit system (SysTick) timer 32-bit watchdog timer On-Chip Memory 128 KB single-cycle flash with two forms of flash protection on a 2-KB block basis 10/100 Ethernet Controller Conforms to the IEEE 802.3-2002 Specification IEEE 1588-2002 Precision Time Protocol (PTP) compliant Full- and half-duplex for both 100 Mbps and 10 Mbps operation Integrated 10/100 Mbps Transceiver (PHY) programmable output user-adjustable from 2.25 V to 2.75 V Battery-backed hibernation module with real-time clock and 256-bytes of non-volatile memory 3.3-V supply brown-out detection Low-power options on controller: Sleep and Deep-sleep modes Low-power options for peripherals: software controls shutdown of individual peripherals User-enabled LDO unregulated voltage detection and automatic reset On-chip temperature sensor ® ® LM3S6633 LM3S6633 Microcontroller Flexible Reset Sources Power-on reset (POR) Reset pin assertion Brown-out (BOR) detector alerts to system power drops Software reset Watchdog timer reset Internal low drop-out (LDO) regulator output goes unregulated Additional Features Six reset sources Programmable clock source control Clock gating to individual peripherals for power savings IEEE 1149.1-1990 compliant Test Access Port (TAP) controller Debug access via JTAG and Serial Wire interfaces Full JTAG boundary scan Package and Temperature 100-pin RoHS-compliant LQFP package ­ Industrial-range (-40°C to +85°C) ­ Extended-range (-40°C to +105°C) 108-ball RoHS-compliant BGA package ­ Industrial-range (-40°C to +85°C) Target Applications Ordering Information Orderable Part Number Description ® LM3S6633-IQC50 LM3S6633-IQC50 a LM3S6633-IQC50 LM3S6633-IQC50 (T) LM3S6633-EQC50 LM3S6633-EQC50 LM3S6633-EQC50 LM3S6633-EQC50 (T) LM3S6633-IBZ50 LM3S6633-IBZ50 LM3S6633-IBZ50 LM3S6633-IBZ50 (T) Stellaris LM3S6633 LM3S6633 Microcontroller Industrial Temperature ® Stellaris LM3S6633 LM3S6633 Microcontroller Extended Temperature ® Stellaris LM3S6633 LM3S6633 Microcontroller Industrial Temperature a. T= Tape and Reel. Evaluation Kit The Luminary Micro Stellaris® LM3S6965 LM3S6965 Evaluation Kit provides the hardware and software tools to speed development of powerful, network-connected devices. Ask your Luminary Micro distributor for part number EKK-LM3S6965 EKK-LM3S6965 (ARM RealView® MDK tools), EKI-LM3S6965 EKI-LM3S6965 (IAR Embedded Workbench® tools), EKC-LM3S6965 EKC-LM3S6965 (CodeSourcery Sourcery G+ tools), or EKT-LM3S6965 EKT-LM3S6965 (Code Red Technologies Code Suite tools). See the Luminary Micro web site for the latest tools available. Motion control Factory automation Fire and security HVAC and building control Power and energy Test and measurement equipment Medical instrumentation Luminary Micro, Inc. · 108 Wild Basin, Suite 350 · Austin, TX 78746 Main: +1-512-279-8800 · Fax: +1-512-279-8879 · http://www.luminarymicro.com Copyright © 2007-2008 Luminary Micro, Inc. All rights reserved. Stellaris, Luminary Micro, and the Luminary Micro logo are registered trademarks of Luminary Micro, Inc. or its subsidiaries in the United States and other countries. ARM and Thumb are registered trademarks and Cortex is a trademark of ARM Limited. Other names and brands may be claimed as the property of others. PB-LM3S6633-01 PB-LM3S6633-01