KT33932UG KIT33932VWEVBE CD33932 MC33932 HSOP44 MC34700EP C0603 C0805

User's Guide Document Number: KT33932UG Rev. 1.0, 7/2008 KIT33932VWEVBE Evaluation Board Figure 1. Evaluation Board Table of

Freescale Semiconductor User's Guide Document Number: KT33932UG KT33932UG Rev. 1.0, 7/2008 KIT33932VWEVBE KIT33932VWEVBE Evaluation Board Figure 1. Evaluation Board Table of Contents Kit Contents / Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Kit Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Setup and Example Demonstrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 EVB Schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Bill of Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 © Freescale Semiconductor, Inc., 2009. All rights reserved. Kit Contents / Packing List 1 Kit Contents / Packing List · · Evaluation Board - KIT33932VWEVBE KIT33932VWEVBE Hardware Document CD, CD33932 CD33932 KIT33932VWEVBE KIT33932VWEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 2 Important Notice 2 Important Notice Freescale provides the enclosed product(s) under the following conditions: This evaluation kit is intended for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY. It is provided as a sample IC pre-soldered to a printed circuit board to make it easier to access inputs, outputs, and supply terminals. This EVB may be used with any development system or other source of I/O signals by simply connecting it to the host MCU or computer board via off-the-shelf cables. This EVB is not a Reference Design and is not intended to represent a final design recommendation for any particular application. Final device in an application will be heavily dependent on proper printed circuit board layout and heat sinking design as well as attention to supply filtering, transient suppression, and I/O signal quality. The goods provided may not be complete in terms of required design, marketing, and or manufacturing related protective considerations, including product safety measures typically found in the end product incorporating the goods. Due to the open construction of the product, it is the user's responsibility to take any and all appropriate precautions with regard to electrostatic discharge. In order to minimize risks associated with the customers applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. For any safety concerns, contact Freescale sales and technical support services. Should this evaluation kit not meet the specifications indicated in the kit, it may be returned within 30 days from the date of delivery and will be replaced by a new kit. Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typical", must be validated for each customer application by customer's technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale was negligent regarding the design or manufacture of the part.FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2008 KIT33932VWEVBE KIT33932VWEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 3 Kit Introduction 3 Kit Introduction · The KIT33932VWEVBE KIT33932VWEVBE Evaluation Board (EVB) is an easy-to-use circuit board that allows the user to exercise all the functions of the MC33932 MC33932 H-Bridge circuit. The EVB communicates to a PC through a USB/SPI Dongle connected to the PC's USB port. The Freescale SPIGen program provides the User Interface to the MC33932 MC33932 EVB's SPI port and allows the user to send commands to the IC. KIT33932VWEVBE KIT33932VWEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 4 Hardware Description 4 Hardware Description g The Hardware Block Diagram is shown below: VBat Reverse Battery And Transient Protection VPWR VDD 2 LED LED VDD VPWR, VDD FAULT LED OUTPUT POLARITY LEDS Charge Pump Cap JUMPERS USB/SPI DONGLE 16 conductor Flat Cable VPWR DATA0 DATA1 CNTL0 CNTL1 DATA2 DATA3 CNTL2 CNTL3 MC 33932 Dual H-Bridge 2 2 INPUT 1 INPUT 2 D1 EN/D2 INPUT 3 INPUT 4 D3 EN/D4 H-BRIDGE OUT1, OUT2 Screw Connectors H-BRIDGE OUT3, OUT4 Screw Connectors VPWR Charge Pump Cap FAULT LED All Grounds Figure 1. Block Diagram This EVB consists of a Dual H-Bridge, a USB to SPI Dongle interface, power conditioning circuitry, and a set of 8 Input Select Jumpers. All +5 volt VDD power required by the EVB is obtained via the USB/SPI Dongle interface. 4.1 LED Display Several LED's are provided as visual output devices for the EVB. A list of the LED devices is shown below: 1. VDD LED - Indicates when +5 Volt supply is connected 2. VPWR LED - Indicates when +12 Volt supply is connected 3. Fault LEDs - Illuminates when one of the H-Bridges detects a fault 4. Output LEDs - Red/Green LED, for each H-Bridge, that indicates which direction the current is flowing in the legs of the H-Bridge. 4.2 I/O Jumper Definitions (J3) The EVB contains seven jumpers that connect the inputs of the 33932 as follows (Bold = factory setting): JUMPER NAME JUMPER POSITION CONNECTION INPUT 1 1-2/2-3 GND/DATA0 INPUT 2 1-2/2-3 GND/DATA1 INPUT3 1-2/2-3 GND/DATA2 INPUT4 1-2/2-3 GND/DATA3 ENABLE/DISABLE 2 1-2/2-3 PullUp/CNTL1 KIT33932VWEVBE KIT33932VWEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 5 Hardware Description ENABLE/DISABLE 4 1-2/2-3 PullUp/CNTL3 DISABLE 1 1-2/2-3 CNTL0/GND DISABLE_2B 1-2/2-3 GND/CNTL2 The DATA0 -DATA3 and CNTL0 - CNTL3 signals are parallel outputs from the USB/SPI Dongle that can be controlled directly from the SPIGen program. An example config file called "MC33932 MC33932_EVB_CONFIGURATION_FILE.spi" is provided on the CD which contains a batch file example. If the user prefers to supply the various MC33932 MC33932 input signals externally, other than from the USB-SPI Interface, the jumpers can be removed and connections can be made to the open pin number 2' s. 4.3 USB/SPI Dongle Connector The USB/SPI dongle connector is a 16 pin,.1" center, dual-row connector that is designed to interface directly to the USB/SPI Dongle unit. The USB/SPI dongle connector consists of the following 16 pins Pin Number Name Description 1 CSB SPI signal, Chip Select Bar 2 CNTL2 Parallel port signal CNTL2 3 SO SPI signal, Serial Out 4 CNTL1 Parallel port signal CNTL1 5 SI SPI signal, Serial In 6 CNTL0 Parallel port signal CNTL0 7 SCLK SPI signal, Serial Clock 8 DATA4 Parallel port signal DATA4 9 CNTL3 Parallel port signal CNTL3 10 DATA3 Parallel port signal DATA3 11 VDD +5 Volt VDD from USB 12 DATA2 Parallel port signal DATA2 13 NC Unused 14 DATA1 Parallel port signal DATA1 15 GND Signal Ground 16 DATA0 Parallel port signal DATA0 This connector mates with the 16 conductor flat cable that connects to the USB/SPI Dongle (KITUSBSPIDGLEVME). KIT33932VWEVBE KIT33932VWEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 6 Hardware Description 4.4 Screw Terminal Connections The EVB contains input and output screw terminal connections to allow easy access to the MC33932 MC33932's drive circuits. The diagram below shows the locations of the screw terminals and their functional definitions: OUTPUT 1 &2 CONNECTOR USB/SPI DONGLE CONNECTOR VBAT CONNECTOR OUTPUT 3 & 4 CONNECTOR Figure 2. Screw Terminals with Definitions 4.5 VBAT Connector The VBAT Connector is a 2 position screw terminal that provides +12 Volt and Ground Terminals. The Ground terminal is marked "GND" and the +12 Volt Terminal is marked "VBAT". 4.6 H-Bridge Output Connectors The H-Bridge Output Connectors are 2 position screw terminals that provides the following two connections: 1) Output 1/2 of the H-Bridge 2) Output 3/4 of the H-Bridge For H-Bridge A the output 1 connector is labeled "OUT1" For H-Bridge A the output 2 connector is labeled "OUT2" For H-Bridge B the output 3 connector is labeled "OUT3" For H-Bridge B the output 4 connector is labeled "OUT4" KIT33932VWEVBE KIT33932VWEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 7 Setup and Example Demonstrations 5 Setup and Example Demonstrations To perform the examples included in the CD the following connections and setup must be performed: 1. Make sure the SPIGen 5.0X program is installed on the PC and it can communicate with the USB/SPI Dongle as described in that kit's documentation. 2. Connect the USB/SPI Dongle to the EVB via a 16 pin ribbon cable. Make sure to orient the cable so that pin1 on both the USB/SPI Dongle and the EVB are connected correctly, pin 1 to pin 1. 3. Connect the USB/SPI Dongle to a PC, LED 2 on the USB/SPI Dongle and the VDD LED on the board should both be illuminated. 4. Attach a +12 VDC supply (do not turn on power yet) to the power connector on the EVB, making sure to observe the GND and +12V terminals. The current capability of the +12V supply should exceed the maximum total current that the number of simultaneously ON loads will require. 5. Attach loads to the OUT1/2 and OUT3/4 terminals . One possible demo load is a 10w halogen G4 Base T3 bulb (used in landscape lighting applications). This load will draw approximately 850 mA and fits nicely into the screw terminals. 6. Launch SPIGen and from the "File" menu, select "Open" and browse to the CD containing the "MC33932 MC33932_EVB_CONFIGURATION_FILE.spi" file. The title on the SPIGen screen should change from "Generic SPI Generator" to "MC33932 MC33932 SPI Generator". 7. Turn on the +12 Volt Supply. Verify that all is working correctly by clicking on the "Extra Pins" button in the SPIGen main screen and then click on the following buttons to set the up the proper conditions: A. Control 0 "Low" B. Control 1 "High" C. Control 2 "Low" D. Control 3 "High" 8. Next, click on the Data 0 "High" button. The OUT1/2 load or bulb should turn on. The OUT 1/2 LED should be glowing green. Clicking on the DATA 0 "Low" button should turn off the load or bulb and the OUT 1/2 LED. Next, click on the Data 1 "High" button. The OUT1/2 load or bulb should turn on. The OUT 1/2 LED should be glowing red. Clicking on the DATA 1 "Low" button should turn off the load or bulb and the OUT 1/2 LED. 9. Next, click on the Data 2 "High" button. The OUT3/4 load or bulb should turn on. The OUT 3/4 LED should be glowing green. Clicking on the DATA 2 "Low" button should turn off the load or bulb and the OUT 3/4 LED. 10. Next, click on the Data 3 "High" button. The OUT3/4 load or bulb should turn on. The OUT 3/4 LED should be glowing red. Clicking on the DATA 3 "Low" button should turn off the load or bulb and the OUT 3/4 LED. If everything described so far occurs then you are ready to proceed with the remaining examples. EXAMPLE 1. RUNNING THE TEST BOTH H-BRIDGES BATCH FILE 1. Click on the "Send a Batch of Commands" Tab in the SPIGen main screen. 2. In the box below the "Commands to Send:" column is a pull-down menu box containing several batch file names. One of these example batch files is labeled "Test Both H-Bridges". 3. Click on this label to load it. You should see a list of commands in the "Command to Send" box. 4. Click on the "Continuous" button and observe that the loads or bulbs you have attached to the EVB board are blinking twice and then going out in succession. There are other demo batch examples that can be run and examined for learning how to use the EVB. KIT33932VWEVBE KIT33932VWEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 8 EVB Schematic 6 EVB Schematic Figure 1. EVB Schematic KIT33932VWEVBE KIT33932VWEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 9 Board Layout 7 7.1 Board Layout Assembly Layer Top Figure 2. Assembly Layer Top KIT33932VWEVBE KIT33932VWEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 10 Board Layout 7.2 Assembly Layer Bottom Figure 3. Assembly Layer Bottom KIT33932VWEVBE KIT33932VWEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 11 Bill of Material 8 Bill of Material Reference Designatio n Value Package Description Mfr PN Freescale Components U7 MC33932 MC33932 HSOP44 HSOP44 Freescale 5.0A Throttle Control H-Bridge Freescale MC34700EP MC34700EP Capacitors C1 C2 C3 C4 C5 C6 C7 C8 C9 C11 C12 .1 uF .1 uF .1 uF 33 nF 33 nF .01 uF .1 uF 47 uF 100 uF 1 uF .01 uF C0603 C0603 C0603 C0603 C0603 C0603 C0805 C0805 C0805 C0805 C0603 C0603 C0603 C0603 PANASONIC_D PANASONIC_D C0603 C0603 C0603 C0603 C13 .01 uF 1 uF .01 uF C0603 C0603 C17 .01 uF C0603 C0603 C18 .01 uF C0603 C0603 C19 .01 uF C0603 C0603 C20 .01 uF 399-1281-1-ND 399-1281-1-ND C0603 C0603 C16 399-1281-1-ND 399-1281-1-ND CAP .1UF 25V CERAMIC X7R 0603 C0603 C0603 C14 CAP .1UF 25V CERAMIC X7R 0603 C0603 C0603 CAP .1UF 25V CERAMIC X7R 0603 399-1281-1-ND 399-1281-1-ND CAP 33000PF 33000PF 50V CERM X7R 0805 PCC1834CT-ND PCC1834CT-ND CAP 33000PF 33000PF 50V CERM X7R 0805 PCC1834CT-ND PCC1834CT-ND Resistors R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R12 R13 R15 R16 1K 470 1K 1K 1K 1K 100 43K 1K 43K 1K 1K 1K 100 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 R0603 MBRB164 MBRB164 5T4G SMBJ40 SMBJ40 D2PAK Diodes D1 D2 DO214AA DO214AA KIT33932VWEVBE KIT33932VWEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 12 Bill of Material Reference Designatio n Value Package Description Mfr PN Other DISAB LE_2B DISAB LE_3 ENABL E ENABL E1 FBA FBB GND INPUT 1 INPUT 2 INPUT 3 INPUT 4 OUTPU T_A OUTPU T_B OUTPU T_LED OUTPU T_LED 1 Q1 Q2 SFA_B SFB_B SF_LE D_A SF_LE D_B USB_S PI_DO NGLE VBAT VDD_L ED VPWR _LED MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA02-1 MA02-1 MA02-1 MA02-1 MA01-1 MA01-1 MA03-1 MA03-1 MA02-1 MA02-1 MA02-1 MA02-1 MA01-1 MA01-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 MA03-1 AK500/2 AK500/2 AK500/2 AK500/2 LT1ED67 LT1ED67 A LT1ED67 LT1ED67 A 1.6X1.6 MMBT290 MMBT290 7ALT1SM D MMBT290 MMBT290 7ALT1SM D MA02-1 MA02-1 MA02-1 MA02-1 SOT23-BEC 1.6X1.6 SOT23-BEC MA02-1 MA02-1 MA02-1 MA02-1 CHIP-LED0603 CHIP-LED0603 CHIP-LED0603 CHIP-LED0603 MA08-2 MA08-2 MA08-2 MA08-2 AK500/2 AK500/2 CHIP-LED0603 CHIP-LED0603 CHIP-LED0603 CHIP-LED0603 Freescale does not assume liability, endorse, or warrant components from external manufacturers that are referenced in circuit drawings or tables. While Freescale offers component recommendations in this configuration, it is the customer's responsibility to validate their application KIT33932VWEVBE KIT33932VWEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 13 References 9 References Following are URLs where you can obtain information on other Freescale products and application solutions: Description URL Data Sheet - MC34932 MC34932 Freescale's Web Site www.freescale.com Freescale's Analog Web Site www.freescale.com/analog KIT33932VWEVBE KIT33932VWEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 14 Revision History 10 Revision History REVISION 1.0 DATE 7/2008 DESCRIPTION OF CHANGES · Initial Release KIT33932VWEVBE KIT33932VWEVBE Evaluation Board, Rev. 1.0 Freescale Semiconductor 15 How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support RoHS-compliant and/or Pb-free versions of Freescale products have the functionality and electrical characteristics of their non-RoHS-compliant and/or non-Pb-free counterparts. For further information, see http://www.freescale.com or contact your Freescale sales representative. For information on Freescale's Environmental Products program, go to http://www.freescale.com/epp. USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 EL516 2100 East Elliot Road Tempe, Arizona 85284 +1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku, Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 LDCForFreescaleSemiconductor@hibbertgroup.com KT33932UG KT33932UG Rev. 1.0 7/2008 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © Freescale Semiconductor, Inc., 2009. All rights reserved.