KA-3529SES-L 1500PCS DSAH1458 JUN/06/2008

PRELIMINARY SPEC Part Number: KA-3529SES-L Features RED-ORANGE Description SINGLE COLOR. The Red-orange device is made with TS

3.5x2.8 mm SMD CHIP LED LAMP PRELIMINARY SPEC Part Number: KA-3529SES-L KA-3529SES-L Features RED-ORANGE Description SINGLE COLOR. The Red-orange device is made with TS AlInGaP light SUITABLE FOR ALL SMT ASSEMBLY AND SOLDER emitting diode. PROCESS. AVAILABLE ON TAPE AND REEL. IDEAL FOR BACKLIGHTING. WHITE SMD PACKAGE, SILICONE RESIN. LOW THERMAL RESISTANCE. PACKAGE: 1500PCS 1500PCS / REEL. MOISTURE SENSITIVITY LEVEL : LEVEL 2a. RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAH1458 DSAH1458 REV NO: V.7 DATE: JUN/06/2008 JUN/06/2008 PAGE: 1 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: R.CHEN ERP: 1201002739 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might leads to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. Do not stack together assembled PCBs containing exposed LEDs. Outside impact may scratch the silicone lens or damage the internal circuitry. 4. The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner diameter of the nozzle should be as large as possible. 5. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup. 6. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup and avoid damage during production. SPEC NO: DSAH1458 DSAH1458 REV NO: V.7 DATE: JUN/06/2008 JUN/06/2008 PAGE: 2 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: R.CHEN ERP: 1201002739 Selection Guide Dice Part No. Lens Type Iv (mcd) [2] @ 150mA v (mlm) [2] @ 150mA Viewing Angle [1] Min. KA-3529SES-L KA-3529SES-L RED-ORANGE (AlInGaP) WATER CLEAR Typ. Min. Typ. 21/2 3800 6000 2500 4000 120° Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2. Luminous intensity / luminous flux: +/-15%. Absolute Maximum Ratings at TA=25°C Parameter Symbol Value Unit Power Dissipation Pt 615 mW Junction Temperature [1] TJ 110 °C Operating Temperature Top -40 To +85 °C Storage Temperature Tstg -40 To +85 °C IF 150 mA IFM 350 mA Thermal Resistance [1] (Junction/ambient) Rth j-a 200 °C/W Thermal Resistance [1] (Junction/solder point) Rth j-S 80 °C/W DC Forward Current [1] Peak Forward Current [2] Notes: 1.Results from mounting on PC board FR4(pad size70mm 2 ), mounted on pc board-metal core PCB is recommend for lowest thermal Resistance. 2.1/10 Duty Cycle, 0.1ms Pulse Width. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device peak Peak Wavelength Red-orange D [1] Dominant Wavelength 1/2 Typ. Max. Units Test Conditions 626 nm IF=150mA Red-orange 618 nm IF=150mA Spectral Line Half-width Red-orange 20 nm IF=150mA C Capacitance Red-orange 25 pF VF=0V;f=1MHz VF [2] Forward Voltage Red-orange 3.6 4.1 V IF=150mA IR Reverse Current Red-orange 10 uA VR = 5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. SPEC NO: DSAH1458 DSAH1458 REV NO: V.7 DATE: JUN/06/2008 JUN/06/2008 PAGE: 3 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: R.CHEN ERP: 1201002739 Red-orange KA-3529SES-L KA-3529SES-L SPEC NO: DSAH1458 DSAH1458 REV NO: V.7 DATE: JUN/06/2008 JUN/06/2008 PAGE: 4 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: R.CHEN ERP: 1201002739 KA-3529SES-L KA-3529SES-L Recommended Soldering Pattern (Units : mm; Tolerance: ±0.1) Tape Specifications (Units : mm) SPEC NO: DSAH1458 DSAH1458 REV NO: V.7 DATE: JUN/06/2008 JUN/06/2008 PAGE: 5 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: R.CHEN ERP: 1201002739 PACKING & LABEL SPECIFICATIONS KA-3529SES-L KA-3529SES-L SPEC NO: DSAH1458 DSAH1458 REV NO: V.7 DATE: JUN/06/2008 JUN/06/2008 PAGE: 6 OF 6 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: R.CHEN ERP: 1201002739