HMC433 HMC433E - Datasheet Archive

v03.1008 FREQUENCY DIVIDERS & DETECTORS - SMT 6 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8 GHz Typical Applications Features

HMC433 HMC433 / 433E v03.1008 FREQUENCY DIVIDERS & DETECTORS - SMT 6 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8 GHz Typical Applications Features Prescaler for DC to C Band PLL Applications: Ultra Low SSB Phase Noise: -150 dBc/Hz · UNII, Point-to-Point & VSAT Radios Single-Ended I/O's · 802.11a & HiperLAN WLAN Output Power: -2 to -3.5 dBm · Fiber Optic Single DC Supply: +3V @ 53 mA · Cellular / 3G Infrastructure 9 mm2 Ultra Small Package: SOT26 Functional Diagram General Description The HMC433 HMC433(E) is a low noise Divide-by-4 Static Divider utilizing InGaP GaAs HBT technology in ultra small surface mount SOT26 plastic packages. This device operates from DC (with a square wave input) to 8.0 GHz input frequency with a single +3.0V DC supply. Single-ended inputs and outputs reduce component count and cost. The low additive SSB phase noise of -150 dBc/Hz at 100 kHz offset helps the user maintain good system noise performance. Electrical Specifi cations, TA = +25° C, 50 Ohm System, Vcc= +3V Parameter Conditions Minimum Input Frequency Min. Typ. 8 Maximum Input Frequency 8.5 Sine Wave Input. [1] Output Power Reverse Leakage SSB Phase Noise (100 kHz offset) Output Transition Time Supply Current (Icc) -12 -3 -15 -7 -5.0 -6.5 GHz +12 +10 -2.0 -3.5 dBm dBm dBm dBm RF Output Terminated, Fin= 4 GHz, Pin= 0 dBm -25 dBm Pin= 0 dBm, Fin= 4 GHz -150 dBc/Hz Pin= 0 dBm, Fout= 882 MHz 120 Vcc= +3.0V 53 ps 71 1. Divider will operate down to DC for square-wave input signal. 6 - 72 Units GHz 0.2 Fin= 1 to 6 GHz Fin= 6 to 8 GHz Fin= 4 GHz Fin= 8 GHz Input Power Range Max. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com mA HMC433 HMC433 / 433E v03.1008 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8 GHz 15 10 10 5 INPUT POWER (dBm) 20 15 INPUT POWER (dBm) 20 Recommended Operating Window 0 -5 -10 -15 5 Min Pin +25 C Max Pin +25 C Min Pin -40 C Max Pin -40 C Min Pin +85 C Max Pin +85 C 0 -5 -10 -15 -20 -20 0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 INPUT FREQUENCY (GHz) 4 5 6 7 8 9 10 INPUT FREQUENCY (GHz) SSB Phase Noise Performance, Pin= 0 dBm, T= 25 °C Output Power vs. Temperature 0 0 SSB PHASE NOISE (dBc/Hz) OUTPUT POWER (dBm) 6 Input Sensitivity Window vs. Temperature -2 -4 +25 C -40 C +85 C -6 -20 -40 -60 -80 -100 -120 -8 -140 -10 0 1 2 3 4 5 6 7 8 9 10 -160 2 10 3 10 INPUT FREQUENCY (GHz) 5 10 6 10 7 10 OFFSET FREQUENCY (Hz) Output Harmonic Content, Pin= 0 dBm, T= 25 °C Reverse Leakage, Pin= 0 dBm, T= 25 °C 0 0 -10 -10 POWER LEVEL (dBm) OUTPUT LEVEL (dBm) 4 10 FREQUENCY DIVIDERS & DETECTORS - SMT Input Sensitivity Window, T= 25 °C -20 -30 Pfeedthru 2nd Harmonic 3rd Harmonic -40 -20 -30 -40 -50 -60 -50 0 1 2 3 4 5 6 7 INPUT FREQUENCY (GHz) 8 9 10 0 2 4 6 8 10 INPUT FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 6 - 73 HMC433 HMC433 / 433E v03.1008 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8 GHz Output Voltage Waveform, Pin= 0 dBm, Fout= 882 MHz, T= 25 °C Absolute Maximum Ratings 300 RF Input (Vcc= +3.0V) -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) -200 250mW Storage Temperature -100 135 °C Continuous Pdiss (T=85 °C) (derate 5mW/°C above 85 °C) 0 +3.5V Maximum Channel Temperature 100 +15 dBm Vcc 200 AMPLITUDE (mV) FREQUENCY DIVIDERS & DETECTORS - SMT 6 Class 1A DC blocking capacitors are required at RF input and RF output ports. Choose value for lowest frequency of operation. -300 23 23.4 23.8 24.2 24.6 25 TIME (nS) ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Typical Supply Current vs. Vcc Vcc (V) Icc (mA) 2.70 42 3.0 53 3.30 63 Note: Divider will operate over full voltage range shown above Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOT FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC433 HMC433 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC433E HMC433E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H433 XXXX [2] 433E XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX 6 - 74 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC433 HMC433 / 433E v03.1008 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8 GHz Pin Number Function Description 1, 4 N/C No Connection 2 GND Pin must connect ro RF/DC ground. 3 IN RF input must be DC blocked. 5 Vcc Supply voltage 3V ± 0.3V. 6 OUT Interface Schematic Divided output must be DC blocked. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com FREQUENCY DIVIDERS & DETECTORS - SMT 6 Pin Description 6 - 75 HMC433 HMC433 / 433E v03.1008 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8 GHz FREQUENCY DIVIDERS & DETECTORS - SMT 6 Evaluation PCB Note: Line lengths on pins 1 & 4 (N/C) are not necessary. List of Materials for Evaluation PCB 105675 [1] Item Description J1 - J2 PCB Mount SMA RF Connector J3 - J4 DC Pin C1 - C2 100 pF Capacitor, 0402 Pkg. C3 1000 pF Capacitor, 0402 Pkg. C4 10 F Tantalum Capacitor, 1206 Pkg. U1 HMC433 HMC433 / HMC433E HMC433E Divide-by-4 PCB [2] 105199 Eval Board The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 6 - 76 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC433 HMC433 / 433E v03.1008 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8 GHz Note: DC blocking capacitor values (C1, C2) and DC decoupling capacitor values (C3, C4) are chosen for lowest frequency of operation. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 6 FREQUENCY DIVIDERS & DETECTORS - SMT Application Circuit 6 - 77