GP1FM520TZ/GP1FM520RZ GP1FM520TZ/ GP1FM520RZ GP1FM520TZ GP1C331 ML93B - Datasheet Archive

 

GP1FM520TZ/ GP1FM520RZ Fiber Optic Transmitter/Receiver s Features s Outline Dimensions (Unit : mm) 9.5 1. Uni-diretional signal

 

GP1FM520TZ/GP1FM520RZ GP1FM520TZ/GP1FM520RZ GP1FM520TZ/ GP1FM520TZ/ GP1FM520RZ GP1FM520RZ Fiber Optic Transmitter/Receiver s Features s Outline Dimensions (Unit : mm) 9.5 1. Uni-diretional signal transmission for plastic optical fiber cables 2. The optical receiver can be directly connectable the TTL, due to the use of OPIC 12 11.5 (Ta=25°C) Parameter Symbol Rating Unit Supply voltage VCC -0.5 to +7.0 V IOH 4 (Source current) Output current mA (GP1FM520RZ GP1FM520RZ) IOL 4 (Sink current) VIN -0.5 to VCC +0.5 V Input voltage (GP1FM520TZ GP1FM520TZ) Operating temperature Topr -20 to +70 °C Storage temperature Tstg -30 to +80 °C *1 Soldering temperature Tsol 260 °C 2.54 (Lead root) (10.5) 6 3.6 1.9 2±0.2 2.54 (Lead root) 0.65±0.2 4.7 2 8.5 1 2 3 1 2 3 4±0.5 s Absolute Maximum Ratings 10.1 11 1. DVD players 2. CD players 3. MD players 1.6±0.2 s Applications VIN VCC GND Unspecified tolerance:±0.3mm Internal equivalent circuit GP1FM520RZ GP1FM520RZ 1 Comp & output circuit Amp. *1 For 5s (2 times or less) Amp. Amp. GP1FM520TZ GP1FM520TZ LED Drive IC 3 Amp. 1 2 OPIC light detector 1 2 3 2 VCC GND VOUT 3 2 1 3 VIN VCC GND LED:GaAlAs Drive IC:Silicone Example of mounting drawing from the soldering face (Unspecified tolerance:±0.1mm) 2.4 1.4 5.7 2.54 2.54 3-1 1.4 5.7 2.4 3.8 "OPIC"(Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and signalprocessing circuit integrated onto a single chip. Notice In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet Internet address for Electronic Components Group http://sharp-world.com/ecg/ GP1FM520TZ/GP1FM520RZ GP1FM520TZ/GP1FM520RZ s Recommended Operating Conditions (GP1FM520TZ GP1FM520TZ) Symbol VCC T Parameter Operating supply voltage *2 Operating transfer rate MIN. 4.75 - TYP. 5.0 - MAX. 5.25 8 (Ta=25°C) Unit V Mb/s *2 NRZ signal, duty 50% s Recommended Operating Conditions (GP1FM520RZ GP1FM520RZ) Symbol VCC T PC Parameter Operating supply voltage *3*4 Operating transfer rate *5 Input optical power level MIN. 4.75 0.1 -24 TYP. 5.0 - - MAX. 5.25 8 -14.5 (Ta=25°C) Unit V Mb/s dBm *3 The above operating transfer rate is the value when NRZ signal, "0101." continuous signal of duty 50% is transmitted *4 The output (H/L level) of GP1FM520RZ GP1FM520RZ are not fixed constantly when it receivers the modulating light (including DC light, no input light) less than 0.1Mb/s *5 Peak emission value s Electro-optical Characteristics (GP1FM520TZ GP1FM520TZ) Parameter Symbol p Peak emission wavelength Optical output coupling with fiber Dissipation current High level input voltage Low level input voltage LowHigh delay time HighLow delay time Pulse width distortion Jitter MIN. Conditions - Refer to Fig.1 Refer to Fig.2 Refer to Fig.2 Refer to Fig.2 Refer to Fig.3 Refer to Fig.3 Refer to Fig.3 Refer to Fig.3 PC ICC VIH VIL tpLH tpHL tw tj 630 -21 - 2 - - - -25 - s Electro-optical Characteristics (GP1FM520RZ GP1FM520RZ) Parameter Symbol p MIN. - - Conditions - Refer to Fig.4 Refer to Fig.5 Refer to Fig.5 Refer to Fig.5 Refer to Fig.5 Refer to Fig.5 Refer to Fig.5 Refer to Fig.5 Refer to Fig.6, PC=-14.5dBm Refer to Fig.6, PC=-24dBm Peak sensitivity wavelength Dissipation current High level output voltage Low level output voltage Rise time Fall time LowHigh delay time HighLow delay time Pulse width distortion ICC VOH VOL tr tf tpLH tpHL tw Jitter tj 2.7 - - - - - -30 - - (Ta=25°C, VCC=5V) TYP. MAX. Unit nm 660 690 dBm -17 -15 mA 4 10 - - V V - 0.8 ns 100 - 100 - ns +25 - ns 1 25 ns (Ta=25°C, VCC=5V) TYP. MAX. Unit nm 700 - mA 40 15 V - 3.5 0.2 0.4 V ns 12 30 ns 30 4 100 - ns - 100 ns +30 - ns 30 1 ns 30 - ns s Mechanical Characteristics Parameter Insertion force, withdrawal force Symbol Conditions MIN. TYP. MAX. Unit - Initial value when a GP1C331 GP1C331 in used 6 - 40 N GP1FM520TZ/GP1FM520RZ GP1FM520TZ/GP1FM520RZ Fig.1 Measuring Method of Optical Output Coupling with Fiber Standard optical fiber cable Optical power meter (Anritsu) ML93B ML93B GP1FM520TZ GP1FM520TZ Unit to be measured VIN VCC GND VCC D The optical power meter must be calibrated to have the wavelength sensitivity of 660nm (0dB=1mW) Note (1) VCC;5.0V (State of operating) (2) To bundle up the standard fiber optic cable, make it into a loop with the diameter D=10cm or more (The standard fiber optic cable will be specified elsewhere.) Fig.2 Measuring Method of Intput Voltage and Supply Current Standard fiber optic cable Optical power meter (Anritsu) ML93B ML93B GP1FM520TZ GP1FM520TZ Unit to be measured VIN VCC GND D ICC VIN VCC Input conditions and judgement method Conditions VIN=2.0V or more VIN=0.8V or less Judgement method -21PC-15dBm, ICC=10mA or less PC-36dBm, ICC=10mA or less Note VCC=5.0V (State of operating) The optical power meter must be calibrated to have the wavelength sensitivity of 660nm (0dB=1mW) GP1FM520TZ/GP1FM520RZ GP1FM520TZ/GP1FM520RZ Fig.3 Measuring Method of Pulse Response and Jitter Standard fiber optic cable GP1FM520TZ GP1FM520TZ Unit to be measured VIN VCC Standard receiver GND Output signal VCC Oscilloscope Input 1 1 0 Input signal 3Mb/s biphase mark PRBS signal 0 Tektronix 7834 or 7934 type Trigger;CH1 Storage mode CH1 CH2 50% Input signal tPLH tPHL Standard receiver output 50% tjr Parameter tjf Symbol Conditions tpLH tpHL tw tjr tjf LowHigh delay time HighLow delay time Pulse width distortion LowHigh jitter HighLow jitter Refer to the above mentioned prescription Refer to the above mentioned prescription tw=tpHL-tpLH Set the trigger on the rise of input signal to measure the jitter of the rise of output Set the trigger on the fall of input signal to measure the jitter of the fall of output Notes (1) The waveform write time shall be 4s. But do not allow the waveform to be distorted by increasing the brightness too much (2) VCC=5.0V (State of operating) (3) The probe for the oscilloscope must be more than 1M and less than 10pF Fig.4 Supply Current Measuring method Input conditions VCC=5.0V PC=-14.5dBm Supply voltage Fiber coupling light output Standard transmitter input signal Measured on an ammeter (DC average amperage) 6Mb/s NRZ, Duty 50% or 3Mb/s biphase mark PRBS signal Fiber optic cable GP1FM520RZ GP1FM520RZ Unit to be measured Standard transmitter VIN VCC GND 5V Input VCC GND A Am meter VCC VOUT GP1FM520TZ/GP1FM520RZ GP1FM520TZ/GP1FM520RZ Fig.5 Measuring Method of Output Voltage and Pulse Response Fiber optic cable Standard transmitter GP1FM520RZ GP1FM520RZ Unit to be measured VCC VIN VCC GND VOUT GND RSO VCC Input 5V RSI 6Mb/s NRZ, Duty 50% CH1 Tektronix 7834 or 7934 type Oscilloscope CH2 Test item Test item Low High pulse delay time High Low pulse delay time Rise time Fall time Pulse width distortion tw=tpHL-tpLH High level output voltage Low level output voltage Notes (1) (2) (3) (4) (5) Symbol tpLH tpHL tr tf tw VOH VOL VCC=5.0V (State of operating) The fiber coupling light output set at -14.5dBm/-24dBm The probe for the oscilloscope must be more than 1M and less than 10pF RSI, RSO:Standard load resistance (RSI:3.3k, RSO:2.2k) The output (H/L level) of GP1FM520RZ GP1FM520RZ are not fixed constantly when it receives the modulating light (including DC light, no input light) less than 0.1Mb/s Standard transmitter Input signal (CH1) 50% tr tf VOH 90% GP1FM520RZ GP1FM520RZ Output signal (CH2) 50% 10% VOL tpLH tpHL GP1FM520TZ/GP1FM520RZ GP1FM520TZ/GP1FM520RZ Fig.6 Measuring Method of Jitter Fiber optic cable Standard transmitter VIN VCC GP1FM520RZ GP1FM520RZ Unit to be measured VCC GND GND VOUT RSO VCC 5V RSI Oscilloscope Input CH1 Tektronix 7834 or 7934 type Trigger:CH1 Storage mode Sweep:AUTO/NORM CH2 Input signal 3Mb/s biphase, PRBS signal Test item Test item Symbol Test condition Jitter tj Jitter tj Input signal 50% GP1FM520RZ GP1FM520RZ Output 50% Set the trigger on the rise of input signal to measure the jitter of the rise of output Set the trigger on the fall of input signal to measure the jitter of the fall of output Notes (1) The fiber coupling light output set at -14.5dBm/-24dBm (2) RSI, RSO:Standard load resistance (RSI:3.3k, RSO:2.2k) (3) The waveform write time shall be 3s. But do not allow the waveform to be distorted by increasing the brightness too much (4) VCC=5.0V (State of operating) (5) The probe for the oscilloscope must be more than 1M and less than 10pF tj tj NOTICE G The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. G Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. G Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: - - - Personal computers - - Office automation equipment - - Telecommunication equipment [terminal] - - - Test and measurement equipment - - - Industrial control - - Audio visual equipment - - Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: - - Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) - - - Traffic signals - - - Gas leakage sensor breakers - - - Alarm equipment - - Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: - - - Space applications - - Telecommunication equipment [trunk lines] - - Nuclear power control equipment - - Medical and other life support equipment (e.g., scuba). G If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is necessary to obtain approval to export such SHARP devices. G This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. G Contact and consult with a SHARP representative if there are any questions about the contents of this publication.