FTR-1419 AN-2025 IEC-825 AT24C01A 1010000X AT24C01A/02/04/08/16 1010111X

40km Extended GBIC Transceiver FTR-1419 Product Features · Up to 1.25Gb/s bi-directional data links · 1310nm DFB

Product Specification 40km Extended GBIC Transceiver FTR-1419 FTR-1419 Product Features · Up to 1.25Gb/s bi-directional data links · 1310nm DFB Laser Transmitter · "Smart" Digital Diagnostics Functions · Extended Operating Temperature Range (0°C to +70°C) · Extended Power Supply Voltage (Operate at 3.3V and 5V) · 1.0625Gb/s Fibre Channel 1.25 Gigabit Ethernet Fully metallic enclosure for low EMI · · · Hot-Pluggable (complies with GBIC specification Rev. 5.4) · Applications Low power dissipation Finisar's FTR-1419 FTR-1419 Extended GBIC transceivers have a maximum fiber length of 40 km, and comply with GBIC Specification Revision 5.41*. They are compatible with the Gigabit Ethernet standard as specified in IEEE Std 802.32* and Fibre Channel FC-PI3*. Additional real time diagnostic functions are also available via the 2-wire serial bus specified for Module Definition "4" GBICs. For details, see Finisar Application Note AN-2025 AN-2025, "Using the Finisar GBIC I2C Test/Diagnostics Port"4. © Finisar Corporation November 16, 2007 Rev.G1 Page 1 FTR-1419 FTR-1419 40km Extended GBIC Product Specification November 2007 I. Pin Out Pin Name Pin # Sequence RX_LOS 1 2 GND 2 2 GND 3 2 MOD_DEF(0) 4 2 MOD_DEF(1) 5 2 MOD_DEF(2) 6 2 TX_DISABLE 7 2 GND 8 2 GND 9 2 TX_FAULT 10 2 GND 11 1 -RX_DAT 12 1 +RX_DAT 13 1 GND 14 1 VCC 15 2 VCC 16 2 GND 17 1 +TX_DAT 18 1 -TX_DAT 19 1 GND 20 1 Table 1. GBIC to host connector pin assignment "Sequence" indicates the order in which pins make contact when the device is hot plugged. See "Table 3: Signal Definitions" in the GBIC Specification Revision 5.41 for a description of the functions of each pin listed above. II. Electrical Power Interface Finisar FTR-1419 FTR-1419 GBICs have an extended power supply voltage range of 3.15V to 5.5V as described in Table 2. They are compatible with both 5V and 3.3V systems. The GBIC specification calls for a range of only 4.75V to 5.25 volts. The 6V maximum voltage is not allowed for continuous operation, however, TX_FAULT and TX_DISABLE circuitry in Finisar GBICs will function at 6V. © Finisar Corporation November 16, 2007 Rev.G1 Page 2 FTR-1419 FTR-1419 40km Extended GBIC Product Specification November 2007 Electrical Power Interface Parameter Supply Current Maximum Voltage Symbol Is Vmax Surge Current 3.15 3.3 / 5 Max 240 6 Units mA V +30 Vcc Typ 180 Isurge Input Voltage Min mA 5.5 V Notes/Conditions Hot plug, above steady state current Referenced to GND Table 2. Electrical power interface III. Low Speed Signals RX_LOS, TX_DISABLE, and TX_FAULT are TTL signals as described in Table 3. MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA) are open drain CMOS signals (see section VI, "Serial Communication Protocol"). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc. If host_Vcc is 3.3V, then they must be pulled to 3.3V. If host_Vcc is 3.3V, do not pull the MOD_DEF pins to 5V. For more detailed information, see sections 5.3.1 5.3.8 in the GBIC Specification Rev. 5.41. Low Speed Signals, Electronic Characteristics Parameter GBIC Output LOW GBIC Output HIGH GBIC Input LOW GBIC Input HIGH Symbol VOL Min 0 Units Notes/Conditions V 4.7k to 10k pull-up to host_Vcc, measured at host side of connector VOH host_Vcc - host_Vcc + V 4.7k to 10k pull-up to host_Vcc, 0.5 0.3 measured at host side of connector VIL 0 0.8 V 4.7k to 10k pull-up to Vcc, measured at GBIC side of connector VIH 2 Vcc + 0.3 V 4.7k to 10k pull-up to Vcc, measured at GBIC side of connector Table 3. Low speed signals electronic characteristics © Finisar Corporation November 16, 2007 Rev.G1 Max 0.5 Page 3 FTR-1419 FTR-1419 40km Extended GBIC Product Specification November 2007 Low Speed Signal Parameters Parameter RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysteresis RX_LOS Assert Delay Symbol Min -31 -0.5 t_loss_on RX_LOS Negate Delay Typ Max -20 44 100 t_loss_off 44 100 TX_DISABLE Assert Time t_off 5 10 TX_DISABLE Negate Time t_on 63 1000 TX_DISABLE Reset Time t_reset 10 TX_FAULT Initialize Time t_init 300 TX_FAULT Assert Time t_fault 100 Units Notes/Conditions dBm dBm dB sec From detection of loss of signal to assertion of RX_LOS sec From detection of presence of signal to negation of RX_LOS sec Rising edge of TX_DISABLE to fall of output signal below 10% of nominal sec Falling edge of TX_DISABLE to rise of output signal above 90% of nominal sec TX_DISABLE HIGH before TX_DISABLE set LOW msec From power on after VCC > 4.5 V sec From occurrence of fault. Table 4. Low speed signal parameters IV. High Speed Electrical Interface All high-speed PECL signals are AC coupled internally. High Speed Electrical Interface Parameter Data Input Voltage Data Output Voltage Duty Cycle PECL rise/fall Bit Error Rate Symbol Vin Vout -Tr,Tf BER Tx Input Impedance Rx Output Impedance Zin Zout Min 650 370 Typ 50 125 75 75 Max 2000 2000 260 10-12 Units mV mV % psec Notes/Conditions PECL differential peak - peak PECL differential peak - peak 20%-80% Differential PRBS 27 - 1 test data pattern Ohm Ohm Table 5. High-speed electrical interface © Finisar Corporation November 16, 2007 Rev.G1 Page 4 FTR-1419 FTR-1419 40km Extended GBIC Product Specification November 2007 V. Optical Parameters Optical Parameters Parameter Transmitter Center Wavelength Side Mode Suppression Ratio (SMSR) Transmitter Optical Output Power Symbol c SMSR Min 1300 30 Pout -2 Transmitter Extinction Ratio Transmitter Eye Opening OMI - 7 60 Optical Rise / Fall Time tr / tf Optical Input Wavelength Total Transmitter Jitter in Optical Input Power Pin Typ Max 1340 +3 200 1270 -23 Total Receiver Jitter 1570 160 -1 160 Units Notes/Conditions nm dB dBm Average power coupled into single mode fiber dB % Conforms to IEEE 802.3 and Fibre Channel Eye Masks ps Unfiltered, 80% - 20% nm ps Peak to peak, filtered dBm BER < 10-12 w/ PRBS 27 - 1 test data pattern @ 1.25Gb/s/ 1.0625Gb/s ps Peak to peak, filtered in loopback Table 6. Optical parameters VI. General Specifications General Parameter Data Rate Symbol Min Typ Max BR 1.25, 1.0625 Units Notes/Conditions Gb/sec Fibre Channel, IEEE 802.3 compatible Fiber Length* L 0 40 km 9um core single mode fiber Total System Budget -23 dB *An attenuation of