DMO-860-051 IRM-8607S-1 PD438B 8607S - Datasheet Archive

 

MODEL NO: ELECTRONICS CO ., LTD. Device Number: DMO-860-051 REV: IRM-8607S-1 ECN: Page: 1.0 1/10 PACKAGE DIMENSIONS DESIGNER

 

EVERLIGHT MODEL NO: ELECTRONICS CO ., LTD. Device Number: DMO-860-051 DMO-860-051 REV: IRM-8607S-1 IRM-8607S-1 ECN: Page: 1.0 1/10 PACKAGE DIMENSIONS DESIGNER CHECKER APPROVED Office: NO 25,Lane 76,Chung Yang Rd,Sec.3 Tucheng,Taipei 236,Taiwan,R.O.C. TEL: 886-2-2267-2000,2267-9936(22Lines) FAX: 886-2-2268-8295 EVERLIGHT MODEL NO: ELECTRONICS CO ., LTD. Device Number: DMO-860-051 DMO-860-051 REV: IRM-8607S-1 IRM-8607S-1 ECN: Page: 1.0 2/10 NOTES 1. This drawing measure is a standard value. All dimensions are in millimeter. 2. In case of designation is tolerance ± 0.3mm. 3. Lead spacing is measured where the lead emerge from the package. 4. Protruded resin under flange 1.0mm Max. 5. Lens color: Black. 6. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 7. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don't reproduce or cause anyone to reproduce them without EVERLIGHT consent. 8. When using this produce, please observe the absolute maximum ratings and the instructions for use outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. EVERLIGHT MODEL NO: ELECTRONICS CO ., LTD. Device Number: DMO-860-051 DMO-860-051 REV: IRM-8607S-1 IRM-8607S-1 ECN: Page: 1.0 3/10 Description The module is a small type infrared remote control system receiver which has been developed and designed by utilizing the most updated IC technology. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated output signal can directly be decoded by a microprocessor. Feature 1. 2. 3. 4. 5. 6. 7. 8. 9. High protection ability to EMI and metal case can be customized. Mold type and metal case type to meet the design of front panel. Elliptic lens to improve the characteristic against Line-up for various center carrier frequencies. Low voltage and low power consumption. High immunity against ambient light. Photodiode with integrated circuit. TTL and CMOS compatibility. Long reception distance. 10. High sensitivity. Application 1. Optical switch 2. Light detecting portion of remote control · AV instruments such as Audio, TV, VCR, CD, MD, etc. · Home appliances such as Air-conditioner, Fan , etc. · The other equipments with wireless remote control. · CATV set top boxes · Multi-media Equipment EVERLIGHT MODEL NO: ELECTRONICS Device Number: DMO-860-051 DMO-860-051 REV: IRM-8607S-1 IRM-8607S-1 ECN: Page: Absolute maximum ratings Parameter Symbol Ratings Supply Voltage Vcc 0~6 -30+85 Operating Temperature Topr -40+85 Storage Temperature Tstg Soldering Temperature Tsol Transmission Distance Half Angle (Horizontal) Half Angle (Vertical) High Level Pulse Width Low Level Pulse Width High Level Output Voltage Low Level Output Voltage 1.0 4/10 (Ta=25) Notice Unit V 4mm from mold body less than 5 seconds 260 Electro Optical Characteristics Parameter TYP Symbol MIN Vcc 4.5 5 Supply Voltage Icc Supply Current B.P.F Center Frequency Peak Wavelength CO ., LTD. MAX 5.5 3 Unit V mA fo - 32.75 - 8 4 940 - - - 45 - deg v - 35 - deg TH 400 - 800 µs TL 400 - 800 µs VH 4.5 - - V VL - 0.2 0.5 No signal input nm h DC voltage KHz p L0 L45 (Ta=25) Condition V m At the ray axis *1 At the ray axis *2 *1:The ray receiving surface at a vertex and relation to the ray axis in the range of = 0° and =45°. *2:A range from 30cm to the arrival distance. Average value of 50 pulses. EVERLIGHT MODEL NO: ELECTRONICS CO ., LTD. Device Number: DMO-860-051 DMO-860-051 REV: IRM-8607S-1 IRM-8607S-1 ECN: Page: 1.0 5/10 TEST METHOD The specified electro-optical characteristics is satisfied under the following Conditions at the controllable distance. !Measurement place A place that is nothing of extreme light reflected in the room. "External light Project the light of ordinary white fluorescent lamps which are not high Frequency lamps and must be less then 10 Lux at the module surface. (Ee10Lux) #Standard transmitter A transmitter whose output is so adjusted as to Vo=400mVp-p and the output Wave form shown in Fig.-1.According to the measurement method shown in Fig.-2 the standard transmitter is specified. However , the infrared photodiode to be used for the transmitter should be p=940nm,=50nm. Also , photodiode is used of PD438B PD438B with VR=5V. (Standard light / Light source temperature 2856°K). $Measuring system According to the measuring system shown in Fig.-3 EVERLIGHT MODEL NO: ELECTRONICS Device Number: DMO-860-051 DMO-860-051 IRM-8607S-1 IRM-8607S-1 ECN: CO ., LTD. REV: Page: 1.0 6/10 Block Diagram Application Circuit RC Filter should be connected closely between Vcc pin and GND pin. EVERLIGHT CO ., LTD. Device Number: DMO-860-051 DMO-860-051 REV: IRM-8607S-1 IRM-8607S-1 ECN: Page: MODEL NO: Fig.-1 ELECTRONICS Transmitter Wave Form 1.0 7/10 D.U.T output Pulse Carrier frequency is adjusted to center frequency of each product. OUTPUT PULSE OF DEVICE IR TANSMITTER OUTPUT WAVE FORM Duty=0.5 Fig.-2 Measuring Method Fig.-3 Measuring System 20cm 10k +5.0± 0.1V L: Transmission Distance Vcc 10uF OUT Standard Transmitter 100k Vout Standard Transmitter D.U.T Vout GND Oscilloscope : Angle Of Horizontal & Vertical Direction EVERLIGHT MODEL NO: ELECTRONICS CO ., LTD. Device Number: DMO-860-051 DMO-860-051 REV: IRM-8607S-1 IRM-8607S-1 ECN: Page: 1.0 8/10 TYPICAL ELECTRICAL/OPTICAL/CHARACTERISTICS CURVES Fig.-4 Relative Spectral Sensitivity vs. Wavelength Fig.-5 Relative Transmission Distance vs. Direction Fig.-6 Output Pulse Length vs. Arrival Distance Fig.-7 Arrival Distance vs. Supply Voltage Fig.-8 Relative Transmission Distance vs. Center Carrier Frequency Fig.-9 Arrival Distance vs. Ambient Temperature EVERLIGHT MODEL NO: ELECTRONICS CO ., LTD. Device Number: DMO-860-051 DMO-860-051 REV: IRM-8607S-1 IRM-8607S-1 ECN: Page: 1.0 9/10 Reliability test item and condition The reliability of products shall be satisfied with items listed below. Confidence level: 90% LTPD: 10% Test Items Test Conditions Vcc=5V,Ta:25 1000hrs 1 cycle -40 +25 +85 Temperature (30min)(5min)(30min) cycle 50 cycle test -10 to +100 Thermal shock (5min) (10sec) (5min) 50 cycle test High temperature Temp: +85 storage 1000hrs Low temperature Temp: -40 storage 1000hrs High temperature Ta: 85,RH:85% High humidity 1000hrs Failure Judgement Criteria Operation life Solder heat Solderability Temp: 260± 5 5sec 4mm Form the bottom of the package. Samples(n) Defective(c) n=22,c=0 L0 L× 0.8 L45 L× 0.8 n=22,c=0 n=22,c=0 n=22,c=0 L: Lower specification limit n=22,c=0 n=22,c=0 n=22,c=0 More than 90% of Lead to be covered n=22,c=0 4mm Form the bottom of the package. by soldering Temp: 230± 5 5sec EVERLIGHT ELECTRONICS CO ., LTD. Device Number: DMO-860-051 DMO-860-051 REV: IRM-8607S-1 IRM-8607S-1 ECN: Page: MODEL NO: 1.0 10/10 Packing Specifications 4.5 3.5 Label 4.0 5.5 19± 0.5 1.Bag 15± 0.5 2.Box 15 22 9 EVERLIGHT Opto-electronic,Compoments IRM - 8607S 8607S - 1 Label 3.Carton E V E R L I G H T 24 33 CPN : Customer's Production Number P/N : Production Number QTY : Packing Quantity CAT : Ranks HUE : Peak Wavelength Label 48 REF : Reference Label Packing Quantity Specification 1. 250 Pcs/1Bag6 Bags/1Box 2. 10 Boxes/1Carton UNITcm LOT NO : Lot Number MADE IN TAIWAN : Production place