VMIACC-0576 VMICPCI-7696 DB-25 P1101 VMICPCI-7697 VMICPCI-7710 RJ-45 - Datasheet Archive

 

CompactPCI Rear Transition Utility Board for VMIC's CompactPCI SBC Boards · Transitions parallel port, two serial ports,

 

VMIACC-0576 VMIACC-0576 CompactPCI Rear Transition Utility Board for VMIC's CompactPCI SBC Boards · Transitions parallel port, two serial ports, USB port, PMC I/O, IDE, and floppy · · · · · · · · · signals from CompactPCI® (CPCI) J3 and J5 connectors to standard I/O connectors for the VMICPCI-7696 VMICPCI-7696, -7697, and -7710 Provides one micro DB-25 DB-25 parallel port connector Provides two RJ45 serial port connectors Provides enhanced IDE 40-pin connector Provides 34-pin floppy disk drive connector Provides one standard USB connector Provides two standard 34-pin connectors for PMC I/O IEEE P1101 P1101.11 compliant CPCI Rev. 2.1 compliant 6U height, 80 mm minimum depth PHOTO NOT AVAILABLE INTRODUCTION - The VMIACC-0576 VMIACC-0576 is designed to be used in conjunction with the VMICPCI-7696 VMICPCI-7696, -7697, and -7710, VMIC's CPCI single-board computer (SBC) products. The VMIACC-0576 VMIACC-0576 mounts in the rear transition area of the backplane and provides access to the serial, USB, parallel, enhanced IDE, and floppy disk connectors by way of the J3 connector, and provides PMC I/O signals by way of the J5 connector. Power Requirements: Power for the VMIACC-0576 VMIACC-0576 is +5 V, supplied through the J3 connector on the CPCI backplane. The CPCI J3 and J5 connectors carry all associated signals from the 6U front mount SBCs through the backplane to the VMIACC-0576 VMIACC-0576 J3 and J5 connectors (see Figure 1). Temperature Range: 0 to 70 C° operating, forced air cooling required HEADERS AND CONNECTORS - The two serial ports use RJ45 connectors. RJ45-to-DB9 adapter cables are provided to connect standard D9 serial peripherals. The USB port is a standard USB connector. The serial port has jumper-selectable data carrier detect (DCD), or ring indicator (RI) signals defined by jumpers E1 (COM1) and E2 (COM2). The IDE and floppy are standard 40- and 34-pin header connectors, respectively. The parallel port is a micro DB-25 DB-25 connector with an adapter cable supplied to a standard 25-pin D connector. IDE and floppy cabling should be limited to a maximum of 19 inches. Relative Humidity Range: 10 to 90 percent, noncondensing TRADEMARKS The VMIC logo is a registered trademark of VMIC. CompactPCI and PICMG are registered trademarks of PCI Industrial Computer Manufacturers' Group. Other registered Ordering Options Sept. 14, 2000 800-800576-000 B VMIACC-0576 VMIACC-0576 ­ A B C ­ 0 0 0 ­ D E F ABC = 000 (Options reserved for future use) The PMC I/O signals are supported on two 34-pin mass termination connectors (AMP 103310-7). Available on the rear panel. For Ordering Information, Call: 1-800-322-3616 or 1-256-880-0444 · FAX (256) 882-0859 E-mail: info@vmic.com Web Address: www.vmic.com Copyright © April 1999 by VMIC Specifications subject to change without notice. PHYSICAL/ENVIRONMENTAL Physical Dimensions: 6U single Eurocard format, single slot Height: 9.2 in. (233.4 mm) Depth: 3.15 in. (80 mm) Thickness: 0.8 in. (20.3 mm) VMIC · 12090 South Memorial Parkway · Huntsville, Alabama 35803-3308 1 VMIACC-0576 VMIACC-0576 VMICPCI-7696 VMICPCI-7696 VMICPCI-7697 VMICPCI-7697 VMICPCI-7710 VMICPCI-7710 Backplane Rear I/O P5 VMIACC-0576 VMIACC-0576 P5 J5 J5 P4 Two 34-pin PMC I/O Connectors P4 J4 J3 P3 P3 J3 J2 Standard USB Connector P2 P1 Floppy Header IDE Header Micro DB-25 DB-25 Parallel Port J1 Two RJ-45 RJ-45 Serial Port Connectors VMIACC-0576 VMIACC-0576 Figure 1. VMIACC-0576 VMIACC-0576 and Rear I/O with VMICPCI-7696 VMICPCI-7696, -7697, or -7710 2 For Ordering Information, Call: 1-800-322-3616 or 1-256-880-0444 · FAX (256) 882-0859