ATS306T/RX6 ATS306R ATS306T 1N4148 1N5817 AST305T IN5817 DIP16 DIP18 - Datasheet Archive

 

7-Function Remote Controller TX6 ATS306T/RX6 ATS306R Actions Semiconductor Co., Ltd. TX6 ATS306T/RX6 ATS306R Data Sheet Version

 

Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Actions Semiconductor Co., Ltd. TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Data Sheet Version 1.00 Shenzhen Office: Tel :86-755-82211737 Fax:86-755-82211771 Hong Kong Office: Tel :852-23978218 Fax:852-23978187 Version1. 00 -1- May 15, 2003 Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Notice: The 7-function TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R heritages the sophisticated architecture and design methodology from TX6/RX6 of Realtek Semiconductor who is one of the leaders of remote controller technology design of toy product. This pair of TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R is the best Transmitter/ Receiver choice of remote control car and fully covers TX6RX6 features with superior performance. The TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R is with more functions and excellent quality, its stability and affectivity promoted to a higher level applications. Actions keeps on leading the designing technique of remote controller of toy product. Remark: Realtek Semiconductor is the trademark of Taiwan Realtek Semiconductor Version1. 00 -2- May 15, 2003 Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R REMOTE CONTROLLER WITH SEVEN FUNCTIONS General Description The TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R are a pair of CMOS LSIs designed for remote controlled car applications. TX6 ATS306T ATS306T is the encoder and RX6 ATS306R ATS306R is the decoder. They provide seven function keys to control forward, Backward, Rightward, Leftward, Turbo, F1 and F2 motions. Besides, a combination of these five common motions (Forward, Backward, Left, Right and Turbo) can be played. And RX6 ATS306R ATS306R provides the ability of two shift gears for Forward and Backward functions. TX6 ATS306T ATS306T is built with auto Power-OFF function. When input key is pulled low, TX6 ATS306T ATS306T will wake up, SO and SC will continuously send out the outputs used in wireless (Non-Carrier) and infrared (Carrier) applications respectively. When a complete code is sent out and all the keys are open, TX6 ATS306T ATS306T will automatically go into power-off mode. RX6 ATS306R ATS306R provides two high effective amplifiers and enhancive Signal Input (SI) recognition circuit for increasing remote control distance. RX6 ATS306R ATS306R has an internal, selectable DC-DC converter that makes the application stable, reliable under lower supply voltage. RX6 ATS306R ATS306R has Motor Limit-Current Protection Circuit for safe and friendly application of RC toy. Block Diagrams TX6 ATS306T ATS306T(Encoder) OSCI Oscillator Timing Generator Latch Circuit OSCO Encoding Circuit RIGHTB LEFTB TURBOB FORWARDB BACKWARDB F1B F2B Logic PC SO SC RX6 ATS306R ATS306R(Decoder) OSCI SI Timing Generator Oscillator OSCO Decoding Circuit AMP VI1 VO1 VI2 Counter VO2 PLA LRTD VT Control Logic Latch LX Version1. 00 DC-DC VDD1 -3- RIGHT LEFT TURBO BACKWARD FORWARD F1 F2 May 15, 2003 Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Pin outs TX6 ATS306T ATS306T LEFTB RIGHTB 1 16 NC 2 15 F1B GND 3 14 OSCI BACKWARDB 4 13 OSCO FORWARDB 5 12 PC TURBOB 6 11 VDD SC 7 10 SO NC 8 9 F2B RX6 ATS306R ATS306R (With DC/DC) RX6 ATS306R ATS306R (Without DC/DC) VO2 1 18 VI2 VO2 1 20 VI2 GND 2 17 VO1 GND 2 19 VO1 SI 3 16 SI 3 18 VI1 OSCI 4 15 OSCI 4 17 VDD OSCO 5 14 TURBO OSCO 5 16 TURBO F1 6 13 FORWARD F1 6 15 FORWARD RIGHT 7 14 BACKWARD F2 8 13 LRTD LEFT 9 12 VDD1 10 11 LX VI1 VDD RIGHT 7 12 BACKWARD F2 8 11 LRTD LEFT 9 10 VT VT Features Wide and Low operating voltage range: 2.0V to 5.0V(TX6 ATS306T ATS306T and RX6 ATS306R ATS306R without DC/DC) A 3.8V zener is built in RX6 ATS306R ATS306R, so a current limitation resistor is required 1.0V ~ 3.0V (RX6 ATS306R ATS306R with DC/DC) Seven-function remote controller controlling Forward/ Backward/ Turbo/ Right/ Left/F1/F2 Provide two transmissive interface (RF and IR) for different application Two speed-shift is realized for Forward and Backward Few external components needed RX6 ATS306R ATS306R's Oscillator only with an external resistor and an external capacitance. Low standby current and low operating current. Typical oscillator frequency: RF: 128KHz IR: 114KHz(Carrier Frequency: 57KHz) IR: 76KHz(Carrier Frequency: 38KHz) Auto Power-OFF function for TX6 ATS306T ATS306T Internal, Selectable Limit-Current protection function. If selected, few external components needed Provide the function of gearing down if swerving Version1. 00 -4- May 15, 2003 Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Provide two high effective amplifiers and enhancive signal input (SI) recognition circuit for very weak signal for increasing remote control distance. Internal, Selectable DC-DC converter, which need few external components. The input voltage ranges from 1.0V to 3.0V, where VOUT can be set to about 3.1V. Start-up is guaranteed from 1.0V inputs. Hold voltage is 0.8V. RX6 ATS306R ATS306R has very strong driving ability about seven function-output Absolute Maximum Ratings Comments* DC Supply Voltage. -0.3V to 6.0V Input/Output Voltage. GND -0.2V to VDD + 0.2V Operating temperature. -10°C to 60°C Storage Temperature. -25°C to 125°C Never allow a stress to exceed the values listed under "Absolute Maximum Ratings", otherwise the device would suffer from a permanent damage. Nor is a stress at the listed value be allowed to persist over a period, since an extended exposure to the absolute maximum rating condition may also affect the reliability of the device, if not causing a damage thereof. Electrical Characteristics TX6 ATS306T ATS306T Typical operating Conditions : VDD = 3.8V, Fosc =128KHz, TA=25, (unless otherwise noted.) Parameter Input Low Voltage Stand by Current Operating Current Symbol Conditions ViL Function Input Pin No function input Unload SO Driving Current IStandBy IDD IDrSO SC Driving Current IDrSC TX6 ATS306T ATS306T Min Typ Max -0.7 0.2 0.1 1.5 1.0 0.6 Units V uA mA Load=0.7V(1N4148 1N4148) 10 mA Load=0.7V(1N4148 1N4148) 10 mA Load=0.7V(1N4148 1N4148) 10 mA PC Driving Current IDrPC Oscillator Frequency RX6 ATS306R ATS306R -20% +20% % Ftolerance Tolerance Fosc=128KHz Code Speed Fosc=128KHz 500 1000 Hz SCode Note 1: "Function input pin" means Forwardb, Backwardb, Rightwardb, Leftwardb, Turbob, F1B and F2B inputs RX6 ATS306R ATS306R(Without DC/DC) Typical operating Conditions: VCC (Power supply) = 4.5V, a Current Limitation resistor (68 ) is between power supply and VDD pin. Fosc = 128KHz, TA=25, (unless otherwise noted.) RX6 ATS306R ATS306R Parameter Symbol Conditions Units Min Typ Max Function Output voltage Operating Current Output Driving Current Oscillator Frequency Tolerance Version1. 00 VO IDD IDriving Ftolerance Unload Unload Load=0.7V(1N4148 1N4148) TX6 ATS306T ATS306T Fosc=128KHz -5- 3.7 3.8 3.9 8.0 mA mA 8.0 -20% V +20% May 15, 2003 % Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Note 1: "Function Output pin" means forward, Backward, Rightward, Leftward, Turbo, F1 and F2 outputs Note 2. Operating Current value is high because of supply voltage higher than zener voltage. The operating current will only be less than 0.8mA if power supply is less than 3.6V. RX6 ATS306R ATS306R (With DC/DC) Typical operating Conditions : VINPUT=1.5V, Fosc =128KHz,TA=25. Using DC-DC converter, (unless otherwise noted.) Parameter Symbol Conditions RX6 ATS306R ATS306R Min DC-DC Output voltage Function Output voltage DC-DC Hold voltage VoH VHOLD Operating Current IDD Output Driving Current Oscillator Frequency Tolerance Ftolerance Max 3.1 3.3 V Unload 3.0 3.1 3.3 V Unload UnloadUse recommended DC-DC circuit 0.8 V 1.0 Load=0.7V(1N4148 1N4148) 5.0 TX6 ATS306T ATS306T 128KHz -20% mA mA +20% Note 1: "Function Output pin" means forward, Backward, Rightward, Leftward, Turbo, F1 and F2 outputs Note 2: "VINPUT" means the input voltage to the DC-DC converter. Note 3: The start-up voltage depends on the application circuit. 1.0V(Start-up) means that the Schhottky Type Diode(1N5817 1N5817) must be used. Version1. 00 units 3.0 VDD IDriving Typ -6- May 15, 2003 % Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Pin Description TX6 ATS306T ATS306T NAME PIN RIGHTB 1 GND 3 BACKWARDB 4 FORWARDB 5 TURBOB 6 SC 7 F2B 9 SO 10 VDD 11 PC 12 OSCO OSCI 13 14 F1B 15 LEFTB 16 Version1. 00 FUNCTION The rightward function will be selected when this pin is connected to GND. (High when open) Negative power supply The backward function will be selected when this pin is connected to GND. (High when open) The forward function will be selected when this pin is connected to GND. (High when open) The turbo function will be selected when this pin is connected to GND. (High when open) Output pin of the encoding signal with carrier frequency (IR) The F2 function will be selected when this pin is connected to GND. (High when open) Output pin of the encoding signal without carrier frequency (Wireless) Positive power supply Power control output pin. When any function key is pulled low, PC will be high logic. If not, it will be Low logic. Oscillator output pin Oscillator input pin The F1 function will be selected when this pin is connected to GND. (High when open) The leftward function will be selected when this pin is connected to GND. (High when open) -7- May 15, 2003 Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R RX6 ATS306R ATS306R NAME VO2 GND PIN PIN (Without (With DC/DC) DC/DC) 1 (1) 2 (2) SI 3 (3) OSCI OSCO F1 RIGHT F2 LEFT 4 5 6 7 8 9 (4) (5) (6) (7) (8) (9) VT 10 (10) LX1 - (11) VDD1 - (12) LRTD 11 (13) BACKWARD FORWARD TURBO VDD VI1 VO1 VI2 12 13 14 15 16 17 18 (14) (15) (16) (17) (18) (19) (20) Version1. 00 FUNCTION Output pin for the Second amplify Negative power supply Input pin of the encoding signal. A inverter must be between SO and SI if connected directly Oscillator input pin Oscillator output pin F1 function output pin (High when active) Rightward output pin (High when active) F2 function output pin (High when active) Leftward output pin (High when active) Input pin of Limit-Current protection function. If no used, it should be connected to GND DC-DC converter Switch signal output pin. The LX pin should be connected with a switch-transistor through a resistor for Limiting the current DC-DC converter voltage output pin. Supply positive power for VDD The Turbo (High speed) function will be cancelled in the swerve motion if it is connected to Gnd Backward output pin (High when active) Forward output pin (High when active) Turbo output pin (High when active) Positive power supply Input pin for the First amplify Output pin for the first amplify Input pin for the Second amplify -8- May 15, 2003 Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Detailed Description (1) Common Functions RC toy's Common Functions include Forward, Backward, Left, Right and Turbo motions. Input/Output Tables Function inputTX6 ATS306T ATS306T Decode ResultRX6 ATS306R ATS306R No any function Input No output Forward (L) Forward pulse (Z) Forward (L)&Turbo (L) Forward (H)&Turbo(H) Turbo(L) Turbo(H) Forward(L)&Left(L) Turbo(L) &Left(L) Forward pulse(Z) &Left(H) Turbo(H)&Left(H) Turbo(L)&Forward(L)&Left(L) Turbo(H)&Forward(H)&Left(H) Backward (L) Backward pulse(Z) Backward(L)&Turbo(L) Backward(H)&Turbo(H) Backward(L)&Left(L) Backward pulse(Z) &Left(H) Turbo(L)&Backward(L)&Left(L) Turbo(H)&Backward(H)&Left(H) Left(L) Left(H) Right (L) Right(H) Note 1: Tab longitudinal data indicates that corresponding Function input keys are pulled down to Gnd (L=LOW) Note 2: Tab longitudinal data indicates that corresponding outputs are active. H=HIGH, Z= 84Hz 66.7% DUTY Pulse Note 3:The frequency of pulse depends on the local oscillator frequency. If the local oscillator frequency is 128KHz, the frequency of pulse will be 84Hz. Note 4:The duty of pulse will not vary in any case. Note 5:The Forward and Backward outputs cannot be active at the same time in any case though AST305T AST305T has the corresponding inputs. So are left and right outputs. (2) F1 and F2 functions RX6 ATS306R ATS306R has two absolute independent Digital Channel: F1 and F2. They also haven't any relation with common functions and other F3, F4 functions. F1 and F2 functions can be used in audio control, Lamp indication and other motor driving. (3) VT: Limit-Current protection At some time the toy's servomotor will be blocked for some reasons, so the function of protecting the motor is very important for us. And then, RX6 ATS306R ATS306R provides the protection function for avoiding it take place. The function is selectable. If not, VT pin should be pulled down to Gnd. If select, the circuit that needs few external components should transform the servomotor current to the voltage for VT input Version1. 00 -9- May 15, 2003 Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Status OFF Functions On Functions A B V Note 1:The abscissa data is the voltage that is from VT input. And ordinate data is the On-Off status of All the IC outputs. Note 2:There are different voltage overturn point of A and B depended on the power supply .For example, If power supply is 3.8V, A point 1.2V, B point 1.7V. And if power supply is 2.7V, A point is 1V, B point 1.35V. (4) LRTD: Auto Gearing Down function The toys should not be played in high speed when it is turning. Just do so, turnover will happen. RX6 ATS306R ATS306R provides the function that prohibits the motion of high speed (Turbo output) while turning if LRTD is connected to Gnd. LRTD function is selectable. If not, Let it be open. The steering output controlled by The toy playerTX6 ATS306T ATS306T Input of LRTD Turbo&Left Inactive( Open) Turbo&Forward&Left Turbo&Backward&Left Turbo&Left Inactive (Open) Inactive (Open) The final outputRX6 ATS306R ATS306R Turbo(H)&Left(H) Turbo (H)&Forward (H)&Left(H) Turbo (H)&backward (H)&Left(H) Active (Low) Left(H) Turbo&Forward&Left Active (Low) Turbo&Backward&Left Active (Low) Note 1: Z=pulse(84Hz 66.7%Duty) H= High logic. Forward(Z)&Left(H) Backward(Z)&Left(H) (5) Two-speed Shift Function How to realize the two-speed shift of servomotor? Please use Forward and Backward output for driving the servomotor. If Turbo is inactive, the motor works in low speed because of pulse driving .And if Turbo is active, the motor works in high speed for High logic driving Version1. 00 - 10 - May 15, 2003 Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Typical Application Circuit Transmitter (TX6 ATS306T ATS306T Fosc=128 KHz) Note 1: Two-Speed shift is realized about forward output. Note 2: The frequency in the table below is 128KHz. The value of resistor (R1) should be changed, if the other oscillator frequency needed. Oscillator Circuit R1 80K 75K 68K TX6 ATS306T ATS306T OSCI OSCO 14 13 R1 75K Fosc About 120KHz About 128KHz About 143KHz Fosc=128KHz Power on-off ANTENNA Control Handle (L and R) 9V BATTERY R 27.145MHz 1K L + TX6 ATS306T ATS306T 1 B 2 3 4 F T Control Handle (F, T and B) 5 6 7 8 RIGHT TEST LEFT F1 GND OSCI BACK OSCO FORW TURBO SC NC PC VDD SO F2 LED 16 120K 4.7uH 47uF 104 2.7uH 47p 15 crystal 14 13 C945 75K 47p 47p C945 12 11 + 10 9 F2 Version1. 00 180 3.8V 104 100 35K 47p 100 100p 47uF 6.8K - 11 - May 15, 2003 10p Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Receiver (RX6 ATS306R ATS306R Fosc =128 KHz) Note 1: The VT pin is pulled down to Gnd because of no using Limit-Current protection. Note 2: Please use the appropriate Current-Limit resistor when using internal zener. Note 3:F2 output is connected with the circuit that needs control. Note 4: The frequency in the table below is 128KHz. The value of resistor (R1) should be changed, if the other oscillator frequency needed. And changing the value of oscillator capacitance (C1) is not necessary Note 5: Without the DC/DC module Oscillator Circuit RX6 ATS306R ATS306R R1 150K 120K 100K OSCI OSCO 4 5 R1 C1 120K Fosc=128KHz 27p C1 27p 27p 27p Fosc About 103KHz About 128KHz About 154KHz ANTENNA 68p 8p 27.145MHz + C380 10uH 15p + 332 560 1.5K 104 120 1N4148 1N4148 100uF 120K 4.7uF 2.2K 103 150 150 MOTOR 8550 104 1K 2.2M 9013 9013 9013 104 8550 104 9013 1K LED 2.2K 10 LEFT VT RX6 ATS306R ATS306R(Without DC/DC module) 150 9 11 LRTD F2 12 BACK 8 7 RIGHT 13 FORW F1 6 TURBO 5 OSCO 14 15 VDD 16 VI1 SI OSCI 4 3 17 VO1 GND 2 VI2 1 2.2M VO2 18 470p 150 MOTOR 8550 120K 1K Lamp&Voice&Motor 2.2K 302 27p 8550 9013 9013 9013 104 9013 Power on-off 1K 4*AA BATTERY Version1. 00 - 12 - May 15, 2003 Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Receiver (RX6 ATS306R ATS306R Fosc =128 KHz) Note 1: Using the Limit-Current Protection function Note 2: Please use the appropriate Current-Limit resistor when using internal zener. Note 3:F2 output is connected with the circuit that needs control. Note 4:Using the LRTD function Note 5:The frequency in the table below is 128KHz. The value of resistor (R1) should be changed , if the other oscillator frequency needed. And changing the value of oscillator capacitance (C1) is not necessary Note 6: Without the DC/DC module Oscillator Circuit RX6 ATS306R ATS306R R1 150K 120K 100K OSCI OSCO 4 5 R1 C1 120K 27p Fosc=128KHz C1 27p 27p 27p Fosc About 103KHz About 128KHz About 154KHz ANTENNA 68p 8p 27.145MHz 10uH 15p + 332 560 120 + C380 1.5K 104 1N4148 1N4148 100uF 120K 4.7uF 2.2K 103 150 150 MOTOR 104 8550 9013 8550 9013 2.2M 1K 9013 104 9013 1K 11 BACK VT FOR 10 VT 12 BACK 1M 10uF VT FORW F1 LRTD TURBO OSCO BACK 15 14 VDD 16 VI1 17 + 1ohm(1W) LEFT 9013 Lamp&Voice&Motor - 13 - RIGHT 27p 8550 8550 9013 1K 302 150 MOTOR 9013 104 9013 Power on-off 1K LEFT F2 8 9 RIGHT 7 6 OSCI 5 4 SI 3 VO2 GND 2 150 LEFT 120K RIGHT 2.2K Version1. 00 1N4148 1N4148 RX6 ATS306R ATS306R(Without DC/DC) 1 2.2M VO1 VI2 18 470p 13 FOR 104 2.2K May 15, 2003 4*AA BATTERY Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Receiver (RX6 ATS306T ATS306T Fosc =128 KHz) Note 1: With the DC/DC module, because of lower supply voltage, and the Schottky Type Diode must be used Note 2: Using the Limit-Current Protection function .The VT pin must be pulled down to Gnd If no using Limit-Current protection. Note 3: The TURBO pin connect with a LED that shows high speed motive status. Note 4: F2 output is connected with the circuit that needs control. Note 5: The frequency in the table below is 128KHz. The value of resistor (R1) should be changed, if the other oscillator frequency needed. And changing the value of oscillator capacitance (C1) is not necessary Oscillator Circuit RX6 ATS306R ATS306R R1 150K 120K 100K OSCI OSCO 4 5 R1 C1 120K 27p Fosc=128KHz C1 27P 27P 27P Fosc About 103KHz About 128KHz About 154KHz ANTENNA 68p 8p 8550 C380 100 10uH 8550 100 MOTOR 15p 27.145MHz + 560 4.7uF 8050 104 1.5K 2.2K 103 560 + 100uF 104 IN5817 IN5817 100uH 11 13 14 Back 16 18 19 20 470p 15 Forw LED 2.2K 17 VDD1 104 Back 2.2M 560 Forw 104 12 VDD1 332 8050 120K 8050 560 LX VDD1 LRTD BACK FORW TURBO VDD VI1 VO1 VI2 103 Focs=128KHz VT LEFT F2 RIGHT F1 OSCO OSCI SI GND VO2 RX6 ATS306R ATS306R(With DC/DC) 2.2M Electromagnetic Power(L&R) 9 8 7 10 100uF Left 2.2K Right 120K 6 5 4 3 2 1 + Lamp&Voice&Motor 8050 302 27p 560 - 14 - 8050 560 Left Right Version1. 00 BATTERY 1.2V May 15, 2003 Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Infrared Application Circuit TransmitterTX6 ATS306T ATS306T Fosc =76 KHz 1~4.7 Fosc=76KHz 16 15 14 LEFTB F1B OSCI 13 OSCO 11 VDD 12 PC 10 SO 9 F2B TX6 ATS306T ATS306T DC:5V 100uF Photo Diode RIGHTB NC GND BACKWAREB FORWARDB TURBOB SC 1 2 3 4 5 6 7 NC 8 8050 ReceiverRX6 ATS306R ATS306R Fosc=76KHz 68 VDD 38KHz OUT IR Receiver GND 18 17 16 15 VI2 VO1 VI1 VDD 14 TURBO 12 11 10 13 FORWARD BACKWARD LRTD VT RX6 ATS306R ATS306R(Without DC/DC) VO2 GND SI 1 2 3 OSCI 4 OSCO 5 F1 6 RIGHT 7 F2 8 100uF DC:5V LEFT 9 Fosc=76KHz 27p Version1. 00 - 15 - May 15, 2003 Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Testing Circuit TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R without DC/DC (128KHz) VCC 5K 75K 16 15 14 LEFTB F1B OSCI 13 OSCO 12 PC 11 10 SO VDD 9 F2B 18 17 16 15 VI2 VO1 VI1 VDD VT VT 68 14 13 12 11 10 TURBO FORWARD BACKWARD LRTD VT VCC TX6 ATS306T ATS306T 4.5V 100uF RX6 ATS306R ATS306R(Without DC/DC) RIGHTB NC GND BACKWAREB FORWARDB TURBOB SC 1 2 3 4 5 6 7 NC 8 VO2 GND SI 1 2 3 OSCI 4 OSCO 5 F1 6 F2 LEFT 8 9 RIGHT 7 120K 27p TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R with DC/DC (128KHz) + 75K 16 15 14 LEFTB F1B OSCI 104 100uF 13 OSCO 12 PC 11 10 SO VDD 9 F2B 20 19 18 17 VI2 VO1 VI1 VDD 16 14 13 12 11 15 TURBO FORWARD BACKWARD LRTD VDD1 LX VCC 5K TX6 ATS306T ATS306T RX6 ATS306R ATS306R(With DC/DC) IN5817 IN5817 VT 4.5V 100uF 560 NC 8 VO2 GND SI 1 2 3 OSCI 4 OSCO 5 120K F1 6 RIGHT 7 F2 LEFT VT 8 9 10 VT RIGHTB NC GND BACKWAREB FORWARDB TURBOB SC 1 2 3 4 5 6 7 8050 100uH 103 27p 1.5V Note 1:There must be an inverter between SO (TX6 ATS306T ATS306T) output and SI (RX6 ATS306R ATS306R) input when connected directly. Version1. 00 - 16 - May 15, 2003 Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Package Information TX6 ATS306T ATS306T DIP16 DIP16 Pin Outline Drawing RX6 ATS306R ATS306R DIP18 DIP18 Pin Outline Drawing Version1. 00 - 17 - Unit in mm Unit in mm May 15, 2003 Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R COB Bonding Figure TX6 ATS306T ATS306T Designation Y X OSCO 568 157 668 157 788 157 118 682 GND OSCI F1B 157 SO VDD LEFTB GND 263 682 682 682 638 682 OSCI 773 682 OSCO PC 398 518 F1B VDD SO F2B NC RIGHTB LEFTB SC TURBOB 157 468 BACKWORDB BACKWARDB 368 PC FORWARDB 157 F2B TX6 ATS306T ATS306T 157 248 SC about 0.98mm 118 TURBOB RIGHTB FORWARDB 917 682 Unit in um X:1120 Y:980 Pad Window: 80×80 about 1.12mm Note: Substrate is connected to GND RX6 ATS306R ATS306R Designation X Y NC FORWARD NC TURBO VDD VI1 VO1 610 90 262 107 90 OSCI 292 90 OSCO 511 90 F1 NC 90 SI LRTD VO2 GND BACKWARDB 690 90 RIGHT 90 1481 90 VT RX6 ATS306R ATS306R VO2 90 1154 LEFT VDD1 about 1.30mm 966 F2 VI2 1641 180 LRTD 1097 1211 LEFT F2 SI 1211 VDD 428 1211 VI1 VT 631 261 1211 VO1 90 1075 VI2 RIGHT F1 OSCO 1211 TURBO NC OSCI GND 1065 1564 FORWARD NC 1641 BACKWARD LX 90 863 Unit in um X:1730 Y:1300 Pad Window: 90×90 about 1.73mm Note: Substrate is connected to VD D Version1. 00 - 18 - May 15, 2003 Actions Semiconductor Co., Ltd. 7-Function Remote Controller TX6 ATS306T/RX6 ATS306T/RX6 ATS306R ATS306R Version List Version 1.00 Release date 2004/5/15 Comment First Version Notice: ACTIONS's products are sold by description only, ACTIONS reserves the rights to make changes in circuit design and/or specification at any time without notice. Accordingly, the reader is cautioned to make sure the latest versions of data sheets are available before placing orders. Version1. 00 - 19 - May 15, 2003