HA-2539 AN541 AN556 HA-2539/883 HA1-2539-2 HA1-2539-5 HA3-2539-5 1-888-INTERSIL - Datasheet Archive

 

Data Sheet September 1998 File Number 2896.3 600MHz, Very High Slew Rate Operational Amplifier Features The Intersil HA-2539

 

HA-2539 HA-2539 Data Sheet September 1998 File Number 2896.3 600MHz, Very High Slew Rate Operational Amplifier Features The Intersil HA-2539 HA-2539 represents the ultimate in high slew rate, wideband, monolithic operational amplifiers. It has been designed and constructed with the Intersil High Frequency Bipolar Dielectric Isolation process and features dynamic parameters never before available from a truly differential device. · Open Loop Gain . . . . . . . . . . . . . . . . . . . . . . . . . . 15kV/V · Very High Slew Rate . . . . . . . . . . . . . . . . . . . . . . 600V/µs · Wide Gain-Bandwidth (AV 10) . . . . . . . . . . . . . . 600MHz · Power Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . 9.5MHz · Low Offset Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . 8mV · Input Voltage Noise . . . . . . . . . . . . . . . . . . . . . . 6nV/Hz With a 600V/µs slew rate and a 600MHz gain bandwidth product, the HA-2539 HA-2539 is ideally suited for use in video and RF amplifier designs, in closed loop gains of 10 or greater. Full ±10V swing coupled with outstanding AC parameters and complemented by high open loop gain makes the devices useful in high speed data acquisition systems. For further design assistance please refer to Application Note AN541 AN541 (Using the HA-2539 HA-2539 Very High Slew Rate Wideband Operational Amplifiers) and Application Note AN556 AN556 (Thermal Safe-Operating-Areas For High Current Operational Amplifiers. For military grade product information, the HA-2539/883 HA-2539/883 data sheet is available upon request. · Output Voltage Swing . . . . . . . . . . . . . . . . . . . . . . . . ±10V · Monolithic Bipolar Dielectric Construction Applications · Pulse and Video Amplifiers · Wideband Amplifiers · High Speed Sample-Hold Circuits · RF Oscillators Pinout HA-2539 HA-2539 (PDIP, CERDIP) TOP VIEW Ordering Information TEMP. RANGE (oC) PACKAGE HA1-2539-2 HA1-2539-2 -55 to 125 14 Ld CERDIP F14.3 NC 2 HA1-2539-5 HA1-2539-5 0 to 75 14 Ld CERDIP F14.3 V- 3 12 NC HA3-2539-5 HA3-2539-5 0 to 75 14 Ld PDIP E14.3 NC 4 11 NC NC 5 10 +V NC 6 9 NC NC 7 8 OUTPUT PKG. NO. +IN 1 14 -IN + - PART NUMBER 13 NC NOTE: No-Connection (NC) leads may be tied to a ground plane for better isolation and heat dissipation. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999 HA-2539 HA-2539 Absolute Maximum Ratings Thermal Information Supply Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . 35V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V Peak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . 33mARMS Thermal Resistance (Typical, Note 2) JA (oC/W) JC (oC/W) CERDIP Package. . . . . . . . . . . . . . . . . 75 20 PDIP Package . . . . . . . . . . . . . . . . . . . 107 N/A Maximum Internal Quiescent Power Dissipation (Note 1) Maximum Junction Temperature (Ceramic Package) . . . . . . .175oC Maximum Junction Temperature (Plastic Package) . . . . . . . . .150oC Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC Operating Conditions Temperature Range HA-2539-2 HA-2539-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC HA-2539-5 HA-2539-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Maximum power dissipation with load conditions must be designed to maintain the maximum junction temperature below 175oC for the ceramic package and below 150oC for the plastic package. By using Application Note AN556 AN556 on Safe Operating Area equations, along with the thermal resistances, proper load conditions can be determined. Heat sinking is recommended above 75oC. 2. JA is measured with the component mounted on an evaluation PC board in free air. VSUPPLY = ±15V, RL = 1k, CL < 10pF, Unless Otherwise Specified Electrical Specifications HA-2539-2 HA-2539-2 HA-2539-5 HA-2539-5 TEMP. (oC) MIN TYP MAX MIN TYP MAX UNITS 25 PARAMETER - 8 10 - 8 15 mV INPUT CHARACTERISTICS Offset Voltage Full - 13 15 - 13 20 mV Average Offset Voltage Drift Full - 20 - - 20 - µV/oC Bias Current 25 - 5 20 - 5 20 µA Full - - 25 - - 25 µA 25 - 1 6 - 1 6 µA Full - - 8 - - 8 µA Input Resistance 25 - 10 - - 10 - k Input Capacitance 25 - 1 - - 1 - pF Offset Current Common Mode Range Full ±10.0 - - ±10.0 - - V Input Current Noise (f = 1kHz, RSOURCE = 0) 25 - 6 - - 6 - pA/Hz Input Voltage Noise (f = 1kHz, RSOURCE = 0) 25 - 6 - - 6 - nV/Hz 25 10 15 - 10 15 - kV/V Full 5 - - 5 - - kV/V Common Mode Rejection Ratio (Note 4) Full 60 72 - 60 72 - dB Minimum Stable Gain 25 10 - - 10 - - V/V Gain Bandwidth (Notes 5, 6) 25 - 600 - - 600 - MHz Output Voltage Swing (Notes 3, 10) Full ±10.0 - - ±10.0 - - V Output Current (Note 3) 25 ±10 ±20 - ±10 ±20 - mA Output Resistance 25 - 30 - - 30 - Full Power Bandwidth (Notes 3, 7) 25 8.7 9.5 - 8.7 9.5 - MHz TRANSFER CHARACTERISTICS Large Signal Voltage Gain (Note 3) OUTPUT CHARACTERISTICS 2 HA-2539 HA-2539 VSUPPLY = ±15V, RL = 1k, CL < 10pF, Unless Otherwise Specified (Continued) Electrical Specifications HA-2539-2 HA-2539-2 TEMP. (oC) MIN Rise Time 25 Overshoot 25 Slew Rate Settling Time: 10V Step to 0.1% HA-2539-5 HA-2539-5 TYP MAX MIN - 7 - - 15 - 25 550 600 25 PARAMETER TYP MAX UNITS - 7 - ns - 15 - % - 550 600 - V/µs - 180 - - 180 - ns TRANSIENT RESPONSE (Note 8) POWER REQUIREMENTS Supply Current Full - 20 25 - 20 25 mA Power Supply Rejection Ratio (Note 9) Full 60 70 - 60 70 - dB NOTES: 3. RL = 1k, VO = ±10V. 4. VCM = ±10.0V. 5. VO = 90mV. 6. AV = 10. Slew Rate 7. Full Power Bandwidth guaranteed based on slew rate measurement using: FPBW = - . 2V PEAK 8. Refer to Test Circuits section of data sheet. 9. VSUPPLY = +5V, -15V and +15V, -5V. 10. Guaranteed range for output voltage is ±10V. Functional operation outside of this range is not guaranteed. Test Circuits and Waveforms IN + OUT 900 NOTES: 100 11. VS = ±15V. 12. AV = +10. 13. CL 10pF. FIGURE 1. TEST CIRCUIT A B Vertical Scale: A = 0.5V/Div., B = 5.0V/Div. Horizontal Scale: 50ns/Div. FIGURE 2. LARGE SIGNAL RESPONSE 3 Vertical Scale: Input = 10mV/Div., Output = 50mV/Div. Horizontal Scale: 20ns/Div. FIGURE 3. SMALL SIGNAL RESPONSE HA-2539 HA-2539 Test Circuits and Waveforms (Continued) 0.001µF V+ NOTES: 14. AV = -10. 15. Load Capacitance should be less than 10pF. 200 INPUT OUTPUT 1µF - 16. It is recommended that resistors be carbon composition and that feedback and summing network ratios be matched to 0.1%. + 0.001µF