AA5060ZGS/E DSAL0985 OCT/06/2010

Part Number: AA5060ZGS/E Green ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features

5.0X6.0mm SURFACE MOUNT LED LAMP Part Number: AA5060ZGS/E AA5060ZGS/E Green ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Description Single color. The Green source color devices are made with InGaN Light Suitable for all SMT assembly and solder process. Emitting Diode. Available on tape and reel. Static electricity and surge damage the LEDS. Ideal for backlighting. It is recommended to use a wrist band or anti-electrostatic Package : 500pcs / reel. glove when handling the LEDs. Moisture sensitivity level : level 3. All devices, equipment and machinery must be electrically RoHS compliant. grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL0985 DSAL0985 REV NO: V.1 APPROVED: WYNEC CHECKED: Allen Liu DATE: OCT/06/2010 OCT/06/2010 DRAWN: C.H.Han PAGE: 1 OF 6 ERP: 1201007047 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or damage the internal circuitry. 4. The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner diameter of the nozzle should be as large as possible. 5. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup. 6. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup and avoid damage during production. SPEC NO: DSAL0985 DSAL0985 REV NO: V.1 APPROVED: WYNEC CHECKED: Allen Liu DATE: OCT/06/2010 OCT/06/2010 DRAWN: C.H.Han PAGE: 2 OF 6 ERP: 1201007047 Selection Guide Part No. Dice Lens Type Viewing Angle [1] Iv (mcd) [2] @ 30mA Min. AA5060ZGS/E AA5060ZGS/E Green (InGaN) 21/2 900 Water Clear Typ. 1300 100° Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity/ luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. peak Peak Wavelength Green D [1] Dominant Wavelength 1/2 Max. Units Test Conditions 520 nm IF=20mA Green 525 nm IF=20mA Spectral Line Half-width Green 35 nm IF=20mA C Capacitance Green 100 pF VF=0V;f=1MHz VF [2] Forward Voltage Green 3.2 4 V IF=20mA IR Reverse Current Green 50 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Green Units Power dissipation 120 mW DC Forward Current 30 mA Peak Forward Current [1] 100 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAL0985 DSAL0985 REV NO: V.1 APPROVED: WYNEC CHECKED: Allen Liu DATE: OCT/06/2010 OCT/06/2010 DRAWN: C.H.Han PAGE: 3 OF 6 ERP: 1201007047 Green AA5060ZGS/E AA5060ZGS/E SPEC NO: DSAL0985 DSAL0985 REV NO: V.1 APPROVED: WYNEC CHECKED: Allen Liu DATE: OCT/06/2010 OCT/06/2010 DRAWN: C.H.Han PAGE: 4 OF 6 ERP: 1201007047 AA5060ZGS/E AA5060ZGS/E Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAL0985 DSAL0985 REV NO: V.1 APPROVED: WYNEC CHECKED: Allen Liu DATE: OCT/06/2010 OCT/06/2010 DRAWN: C.H.Han PAGE: 5 OF 6 ERP: 1201007047 PACKING & LABEL SPECIFICATIONS SPEC NO: DSAL0985 DSAL0985 REV NO: V.1 APPROVED: WYNEC CHECKED: Allen Liu AA5060ZGS/E AA5060ZGS/E DATE: OCT/06/2010 OCT/06/2010 DRAWN: C.H.Han PAGE: 6 OF 6 ERP: 1201007047